How do you remove an axle from a Honda Civic?
Attach a 17mm socket and ratchet on one end, and a 17mm wrench on the other. Hold wrench in place while the ratchet undoes the bolt. Once bolt is loose, use the hammer to get it off. Figure 7. As you can see, the axle goes right through the strut. Hence the need to remove it. With everything out of the way, the axle is ready to be pulled out.
What’s the name of the new Honda Civic?
The third-gen Honda Civic saw the release of a radically-new exterior design that more closely resembled the Civic we know today. It was also in this generation that Honda decided to mix things up a bit. With the addition of a fastback coupe ( labeled the CRX ), as well as a larger 5-door shuttle-wagon.
What kind of transmission does a Honda Civic have?
Transmissions included a standard 5-speed manual, as well as a 4-speed automatic on the DX hatchback, and all sedan models. The sixth generation of the Civic was still a step forward, though, not as big a step compared to previous years. Sedans were still available in DX, LX, and EX trims, but Honda reduced the hatchback to only two, the CX and DX.
When did the Honda Civic 4 generation come out?
1988 saw the release of the fourth generation of the Civic. With it came new, more powerful engines, as well as a suite of new model packages. Two of the most notable changes, though, were the addition of a double-wishbone suspension for the front and rear, and 4-wheel disc brakes.
Where do you change the alternator on a Honda Civic?
Replacing your alternator does not require any specialty tools. It can be a lengthy job, and also requires a lot of work inside the engine bay. So if you don’t feel comfortable being underneath the car, then it is recommended having this done at a repair shop. Locate the appropriate spot underneath the car to jack up your Civic.
How do you jack up a Honda Civic?
Locate the appropriate spot underneath the car to jack up your Civic. Set the car on jack stands, and proceed to disconnect the car battery. Disconnect the negative (black) terminal first, and then the positive (red). Figure 1. Always disconnect the battery before performing any mechanical work.
Where is the B Terminal on a Honda Civic?
Remove the B terminal by removing the bolt located to the right of the 4P connector. Loosen the adjusting bolt located above the belt. Loosen the upper bracket support. Remove splash shield underneath the car to access alternator from below if necessary. Figure 2. Unclip the green 4P connector. Figure 3. Remove the alternator adjusting bolt.
What happens if you replace window molding in Honda Civic?
If significant wear and tear occurs, the window could loosen, causing further damage. Also, rain could seep into your Honda Civic and cause damage to your car’s interior panels or carpeting. Using just a few simple tools, you can safely and easily replace the old, worn, cracked window molding in your car.
How do you replace a CV axle in a car?
You can remove the band from the inner boot to help the old axle pass through. Insert the new CV axle into the transmission housing. Just as you removed the old CV axle, insert the new one into the same spot in the transmission housing. The peg will slide all the way in until the axle is flush against the housing.
What’s the best way to change an axle?
By this time, you can put the wheel back on the vehicle (again, the same as you would when changing a tire). After the wheel is on, you can lower the car off the jack and jack stands. Tighten the axle nut. Finally, you can retighten the axle nut once the vehicle is back on the ground.
Where is the outer tie rod on a CV axle?
Unbolt the outer tie rod from steering knuckle. The outer tie rod is literally a rod bolted to the steering knuckle, which is just behind the rotor. This piece will likely be bolted with another 17mm bolt. Like the axle nut, this bolt may be held in place with a cotter pin. Penetrating lubricant may help you more easily remove the pin and bolt.
Do you need to replace the front axle on a Honda Civic?
Axles need to be replaced as necessary, and failure to do so could lead to big problems. This job is straightforward, but it requires spending some time under the car, so you may want to visit a shop if you aren’t comfortable doing this. Loosen front lug nuts.
Do you need to replace the front wheel axle?
The axle is the part that makes your front wheels turn. Axles need to be replaced as necessary, and failure to do so could lead to big problems. This job is straightforward, but it requires spending some time under the car, so you may want to visit a shop if you aren’t comfortable doing this.
Which is the right side of the axle to replace?
And it’s usually the right side that goes first because here in the lefthand-drive US of A, we turn sharper around righthand corners than lefthand ones. Sometimes the rubber boots covering the joints fail from age or are torn by road debris, letting the grease out and dirt and water in.
What should I do if my front drive axle fails?
A failed boot requires immediate disassembly and cleaning, fresh lube and a new boot. This joint shows minor wear. Balls and grooves will show wear before the joint fails completely. Replacing a front-wheel-drive axle is straightforward, although physically demanding.
How do you remove a wheel from a CV axle?
Tape the steering knuckle joint with a hammer (hitting the knuckle where the rod goes through and not the threaded portion of the tie rod) to help remove it. Unbolt the hub from the strut tower. Two more 17mm bolts will connect the wheel hub to the strut tower.
How to replace CV axle shaft and output shaft?
Bolt on the suspension strut to the steering knuckle along with the brake hose bracket bolt. Install the wheel and remove your jack and jack stands. Torque the axle shaft nut to around 150 lbs. Applying your body weight to the breaker bar should put you close to that torque. Fill your transmission with ATF.
How do you replace an axle on a Honda Civic?
Finish removing the lug nuts once the car is up. The axle nut is a 32mm nut that has been “notched” in for safety. Break the notch with a small chisel or screwdriver, and then remove the axle nut using your ratchet and 32mm socket. These nuts are fastened in excess of 120 ft/lb, so don’t be afraid to put some muscle on it.
What kind of axle do you need for a Honda Fit?
Here we replace the front right axle, or driveshaft, in a 2008 Honda Fit. We use a Cardone axle driveshaft from Rock Auto. Due to factors beyond the control of LV Equipment LLC, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.
What’s the best way to remove an axle nut?
Break the notch with a small chisel or screwdriver, and then remove the axle nut using your ratchet and 32mm socket. These nuts are fastened in excess of 120 ft/lb, so don’t be afraid to put some muscle on it.
The axle is the part that makes your front wheels turn. Axles need to be replaced as necessary, and failure to do so could lead to big problems. This job is straightforward, but it requires spending some time under the car, so you may want to visit a shop if you aren’t comfortable doing this.
Break the notch with a small chisel or screwdriver, and then remove the axle nut using your ratchet and 32mm socket. These nuts are fastened in excess of 120 ft/lb, so don’t be afraid to put some muscle on it.