How do you remove a heater control valve?
Another way to release the hose with a hose pick tool. This tool has a pointed end that you can slip under the hose to create a gap between the hose and valve. Slide the pick tool under the rubber hose and move the tool along the area of the hose to pry the rubber hose from the control valve.
How can I Fix my Jeep Grand Cherokee heater treater?
Heater Treater’s Dual Zone Blend Door fix is for Grand Cherokee Limited’s with dual zone temperature controls. You can read the fail codes on the system by following this procedure: Turn the ignition switch on and turn on the AC system. You should see a temp display for the two sides.
Why is my Jeep Cherokee heater not working?
What are common reasons my Jeep Cherokee has heater problems? While there are a variety of reasons your Jeep Cherokee heater is not working, the most common 3 are a broken heater blower motor, a problem with the thermostat, or a failed heater blower motor resistor.
How to turn on heat in Jeep Grand Cherokee?
Check for a broken limit pin on the axle and check that you can turn it ~50 degrees of movement between the two stop points. Start the GC and turn on the AC. You should be able to manually switch between heat and AC by turning the axle with your fingers.
How to fix a Jeep Cherokee heat and AC?
The pictures show the hardware provided for the fix. All work is done from the foot area of the passenger side of the Jeep, with a Dremel cut in the bottom of the heater box…no removal of the dash panel or evacuating the AC system and draining the radiator.
Where do you change the radiator on a jeep?
All work is done from the foot area of the passenger side of the Jeep, with a Dremel cut in the bottom of the heater box…no removal of the dash panel or evacuating the AC system and draining the radiator. Once completed, the alterations are under the dash panel in the foot area and are not visible.
What should I do about my Jeep Cherokee blend door?
This is a kit to do a complete repair on the blend door malfunction that is common to the 97- 01 Jeep Cherokee. Every Cherokee in this range either has, or will have, this common failure.
What happens when a heater control valve is leaking?
If the valve is leaking, you may see dried residue close to the color of the system coolant. These are the remnants of some of the dyes and chemicals used in the engine coolant. The heater control valve is part of the vehicle’s cooling system as coolant does flow through this valve.
Where is the heater control valve on a Chevy Astro?
The heater control valve exists in a part of the system after the engine, but before the radiator so the coolant in this part of the system has been heated when it arrives to the valve. Once the valve is activated, the heated coolant can flow into the passenger compartment and fill the heater core.
How does the heater control valve work in a car?
The heater control valve is part of the vehicle’s cooling system as coolant does flow through this valve. Engine operation generates a lot of heat and this heat gets transferred from the engine assembly to the liquid coolant in the cooling system to be cooled by air flowing across the radiator.
Can a faulty heater control valve be repaired?
To repair a faulty switch, you sometimes have to replace the heater control. Depending on the amount of vacuum, the vacuum motor will close off the flow of engine coolant fully or partially. However, even if the heater control supplies vacuum the mechanical portion of the valve can fail, preventing the heater control valve from closing.
How does a heater control valve work in a car?
In some cars, the heat is regulated by a heater control valve that controls the flow of hot engine coolant from the engine to the car’s heater core. On older vehicles, the valve is operated by a cable, while newer vehicles used a vacuum actuator controlled valve. A heater control valve can fail in several ways.
What to do if your heater is not blowing hot air?
Pinch off the hose on the outlet side of the heater control valve (the hose closest to the firewall) and drive the vehicle at highway speeds. If the blower stops blowing hot air, you’ve found the problem.
How does an air conditioner control valve work?
During times when the air conditioner is in use, the heater control valve closes, preventing engine coolant from entering the heater core. The result is less heat in the passenger compartment, allowing the air conditioner to work more efficiently.