How do you remove a front drive drive bearing?
Step 1: Remove the front driveshaft. The front driveshaft is attached to the transmission output shaft and connected by four bolts. On some rear wheel drive vehicles, the bearing block bolts thread into nuts that are solidly mounted or welded onto the frame.
How to improve seal on wheel end bearing?
For improved seal performance: • Work with clean tools. • Pre-lube the seal with the same lubricant being retained. • Double-check the seal part number before installation. • Inspect the shaft and bore for burrs, nicks or other damage before installing a new seal. • Never reuse old seals. • Never hammer directly on a seal.
How are driveshafts attached to center support bearings?
The two driveshaft’s that attach in the center support bearings are attached on opposite sides of the vehicle as well. The front drive shaft is attached to the output shaft coming out of the transmission, while the rear driveshaft’s propeller shaft is attached to the yoke that comes out of the rear axle differential.
What happens when a drive support bearing fails?
A failed bearing is unable to support the driveshaft, and as a result the driveshaft will flex, causing a vibration and shuttering sensation that can be felt throughout the vehicle when it’s broken.
How to install transmission output shaft seal on rear wheel drive truck?
How to Install a Transmission Output Shaft Seal on a Rear Wheel Drive Truck. – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.
How do you remove a front slip yoke drive shaft?
If you have a front slip yoke drive shaft, remove the bolts to the drive shaft on the rear axle. Use a large flat screwdriver and slightly pry out the drive shaft and universal joint from the yoke on the axle.
What causes the output shaft seal to bend?
This puts a lot of stress on the output shaft seal and makes the seal bend. When the seal is hard, bending the seal will allow fluid to escape the transfer case and allow dirt, debris, and water to enter into the transfer case. The most common sign of output shaft seal failure is the drip of gear oil leaking from the seal.
How do you replace an output shaft seal?
Step 1: Prepare the new output shaft seal. Get a tube of oil resistant silicon and place a fine film of silicon on the shell (outside area) of the new output shaft seal. Step 2: Get a seal installer tool that is made for an output shaft seal. Use a hammer and smack the seal installer to draw in the seal into the output shaft housing.
What happens when a driveshaft is removed from a car?
Something you should know that may not be thought of is when a driveshaft is removed the car will no longer be in park. The car will roll because the link between the drive wheels and transmission is removed. You will need to raise the car or truck up using a floor jack and jackstays. Wear protective eyewear and gloves before you begin. 1.
What should I do if my drive shaft is leaking?
Using both hands gently slide the driveshaft from the transmission or transfer case. A small amount of fluid might leak out so have a fluid catch basin ready. This would be a good time to replace leaking transmission tail housing seal, universal joints or if removing the transmission or differential repairs are needed. 5. Check U joints
Can a 12 point head be removed from a driveshaft?
These bolts will be very tight so use good quality tools to avoid stripping. Some bolts can head 12 point heads as in this example which used a 13mm 12 point socket to remove. These bolts also use lock tight to avoid coming loose while in operation and can be reapplied when reinstalling. 3. Remove Driveshaft Flange
Something you should know that may not be thought of is when a driveshaft is removed the car will no longer be in park. The car will roll because the link between the drive wheels and transmission is removed. You will need to raise the car or truck up using a floor jack and jackstays. Wear protective eyewear and gloves before you begin. 1.
Where can I buy Mercury outboard motor parts?
Mercury Outboard Parts and Mercury Marine Motors are among the most popular outboard motors for sale today. When you are looking for specific Mercury Marine Part Numbers, why pay the normal high prices for OEM Mercury Marine Parts & Accessories when you can shop PPT online for huge discounts and free shipping.
Using both hands gently slide the driveshaft from the transmission or transfer case. A small amount of fluid might leak out so have a fluid catch basin ready. This would be a good time to replace leaking transmission tail housing seal, universal joints or if removing the transmission or differential repairs are needed. 5. Check U joints
Where to look for specific Mercury Marine part numbers?
When you are looking for specific Mercury Marine Part Numbers, why pay the normal high prices for OEM Mercury Marine Parts & Accessories when you can shop PPT online for huge discounts and free shipping. Using our simple outboard catalog parts lookup you can quickly locate the correct OEM Parts from Mercury Marine near you.