How do you remove a door panel on a Hyundai Accent?
On most models, there is a plastic cover over the hole. Remove the covers and the screws. Remove the screw that holds the plastic cover just in front of the door handle and remove the cover. There is a triangular cover on the top front of the door panel that covers the mounting surface for the outside mirror.
How do you replace scuff trim on a Hyundai Accent?
1. Using a screwdriver or remover, remove the front door scuff trim (A). [Front] 2. Remove the rear seat cushion. (Refer to the BD group – “Rear Seat”) 3. After loosening the mounting screws, then remove the rear door scuff trim (A). [Rear] 4. Installation is the reverse of removal. Replace any damage clips. Door Scuff Trim Replacement
How do you remove a trim fastener from a door?
Insert the common screwdriver between the door panel and the door at the upper most level of the rear of the door panel and slide it down until it contacts the first trim fastener. Carefully pry the fastener from its hole in the door. It is good to note that these door panels are nothing more than cardboard covered in material.
What should I remove from my door panel?
Look behind the door panel and disconnect the electrical connectors from the window switch, door lock switch and the mirror as well. Remove the electrical connector that leads to the lower left marker light. Don Bowman has been writing for various websites and several online magazines since 2008.
How do you remove trim from a door panel?
Let’s Get Started. 1. Remove Small Trim Pieces. Most door panels will have small trim pieces located at the top of the panel at either the right or left side. Use a small screw driver or trim removal tool and detach (pop off) any trim pieces above the door panel. Here is an upper trim piece to the left of the panel.
How to remove interior trim from Hyundai Accent?
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface Take care not to bend or scratch the trim and panels. 1. Remove the front door scuff trim. 2. Using a screwdriver or remover, remove the cowl side trim (A). 3. Installation is the reverse of removal. Replace any damaged clips.
Where is the seal on a Hyundai Accent door panel?
The door panel is hooked onto the top ledge where the window felt or seal is located. The curved edge at the top hooks to the horizontal ledge so while the bottom of the panel is tipped outward lift up to unhook and move the panel away from the door a few inches.
How do you remove fascia from a door?
Use a small screw driver or trim removal tool and detach (pop off) any trim pieces above the door panel. Here is an upper trim piece to the left of the panel. These pieces must be removed before removing the panel. 2. Remove Plastic Fascia Pieces
On most models, there is a plastic cover over the hole. Remove the covers and the screws. Remove the screw that holds the plastic cover just in front of the door handle and remove the cover. There is a triangular cover on the top front of the door panel that covers the mounting surface for the outside mirror.
How is the door panel on a Hyundai held on?
Hyundai door panels are held on primarily with trim fasteners which resemble large plastic stove bolts. They have a large, round, flat head and serrated shaft that hold through use of friction from the serrations. A common screwdriver and a Phillips screwdriver will be needed.
Look behind the door panel and disconnect the electrical connectors from the window switch, door lock switch and the mirror as well. Remove the electrical connector that leads to the lower left marker light. Don Bowman has been writing for various websites and several online magazines since 2008.
Hyundai door panels are held on primarily with trim fasteners which resemble large plastic stove bolts. They have a large, round, flat head and serrated shaft that hold through use of friction from the serrations. A common screwdriver and a Phillips screwdriver will be needed.
How to disassemble and replace exterior door handle?
Push the panel forward gently to release the rear of the panel. Wires are still attached to the panel, so set it vertically along the seat between the door frame to get it out of the way. Step 15: Bend over and look up into the door at the rear end to find the plug for the exterior door handle’s keyless entry button.
How do you remove a door panel from a car?
Insert a screwdriver into the edge of the armrest cover and pry it off. The armrest cover may be concealing a fastening screw. Take a flathead screwdriver and wedge it into the crack at the edge of the panel. Apply gentle pressure to pop it out and remove it.
Insert the common screwdriver between the door panel and the door at the upper most level of the rear of the door panel and slide it down until it contacts the first trim fastener. Carefully pry the fastener from its hole in the door. It is good to note that these door panels are nothing more than cardboard covered in material.