Menu

Navigation

How do you read OBD1 engine codes?

Posted on by Arif Clayton

How do you read OBD1 engine codes?

To get the check engine codes to flash in your dash panel, use a jumper wire or a paper clip and connect terminals A and B of the diagnostic connector. Turn your ignition key on with engine off and the codes should start to blink. All codes should start with code 12 which is one long flash followed by 2 short flashes.

Where does the trouble code go on a Honda Civic?

When the ecu sets a trouble code,the check engine light will come on and the ecu stores the code in the memory. The trouble code will remain in the memory until voltage to the ecu is disconnected. Removing the hazard fuse in the main fuse panel for 10 seconds will reset all trouble codes.

Where is the Diagnostic Code on a Honda?

There are many resources you can use to check and diagnose these DTCs (diagnostic trouble codes). For 1992-1995 (OBD1) vehicles you can check these yourself by using the method shown in the picture below. In OBD1 Hondas and Acuras there is a diagnostic port and a two-pin connector located under the passenger-side dashboard.

How to get Honda OBD1 code 0 and 11?

To restart the code gathering sequence turn the ignition key “OFF” and then “ON” again. To clear codes after the repair has been made, disconnect the negative battery terminal for thirty seconds and reconnect. Code 0 and 11 Electronic Control Module (ECM) Computer

What is the code for the Check Engine light?

Your check engine light will then start to flash. Every long flash is a digit in the “tens” place in the code, and a short flash is a digit in the “ones” place. So, if you see two long flashes and five short flashes, you have a Code 25. There will be a long pause between codes. Read all the codes until they start to repeat themselves.

When the ecu sets a trouble code,the check engine light will come on and the ecu stores the code in the memory. The trouble code will remain in the memory until voltage to the ecu is disconnected. Removing the hazard fuse in the main fuse panel for 10 seconds will reset all trouble codes.

Where do I find the DTC codes on my Honda?

To view any DTC’s stored in the PCM memory (without a code reader), fit a bridging wire into service check connector then turn the ignition switch to the ON position. If any codes are present, they will blink a sequence in the MIL to indicate a system or component failure.

What kind of engine does a Honda Civic have?

D16Y4. Found in: 1998–2000 Civic 1.6 iES (Turkey) 1996–2000 Civic CXi,GL,GLi (New Zealand,Australia) Bore and Stroke: 75.0 × 90.0 mm (2.95 x 3.54 in) Displacement: 1,590 cc (97 cu in) Compression: 9.4:1; Power: 120 hp (88.0 kW) at 6,400 rpm; Torque: 144 nm at 5,000 rpm; Redline: 6,800 rpm; Rev-limiter: 7,200 rpm; Fuel Control: OBD-2 MPFI

Where can I find a Honda check engine light code?

A fault code reader is required to retrieve or clear codes via this connector. To view any DTC’s stored in the PCM memory (without a code reader), fit a bridging wire into service check connector then turn the ignition switch to the ON position.

How do you read obd1 engine codes?

Posted on by Arif Clayton

How do you read obd1 engine codes?

To get the check engine codes to flash in your dash panel, use a jumper wire or a paper clip and connect terminals A and B of the diagnostic connector. Turn your ignition key on with engine off and the codes should start to blink. All codes should start with code 12 which is one long flash followed by 2 short flashes.

Where is the trouble code located on a Honda Accord?

Insert the jumper wire in the 2 PIN service connector between pins 1 and 2. You should also see a 3 PIN connector. This is used for a trouble code scanner. Trouble codes will be stored in the ECU even if the check engine light is not on.

Where is the OBD plug on a Honda Accord?

Since your Honda Accord is pre-OBD-II it does not have an OBD-II Data Link Connector which would normally used on a 1996 and newer Honda Accord; to pull trouble codes with a scan tool. On older model Accords, you can retrieve trouble codes by inserting a jumper wire at the diagnostic connector located in the passenger side kick panel.

What are the codes on the Honda OBD1?

The Most Common Honda and Acura OBD1 Codes Code Meaning Code 4 Crank position sensor Code 6 Engine coolant temperature Code 7 Throttle position sensor Code 8 Top dead center sensor

How to read codes from your check engine light?

That’s two clicks for Honda users. Wait a second and keep your eye on the check engine light. You should see it start to light up in a series of flashes. The light is blinking in a simple code of long and short. Long blinks mean “10” and short blinks mean “1”.

Where is the Diagnostic Code on a Honda?

There are many resources you can use to check and diagnose these DTCs (diagnostic trouble codes). For 1992-1995 (OBD1) vehicles you can check these yourself by using the method shown in the picture below. In OBD1 Hondas and Acuras there is a diagnostic port and a two-pin connector located under the passenger-side dashboard.

Where to find OBD I code on Honda Civic?

Honda Motor Corporation OBD I diagnostic trouble codes are retrieveable without any special tools by simply following the instructions here. The codes are listed for Accord or Civic models seperately when required. The codes are defined as to what system is affected. When possible we give the more commonly known OBD II component name.

Where is the plug on a Honda Accord?

Just stick your head up under the dashboard on the passenger side and look around for a plug that isn’t connected to anything. If you don’t have a Honda Accord then do a search online for where your plug is located and you will probably find some good leads.

That’s two clicks for Honda users. Wait a second and keep your eye on the check engine light. You should see it start to light up in a series of flashes. The light is blinking in a simple code of long and short. Long blinks mean “10” and short blinks mean “1”.