How do you change the spark plugs in a Toyota Sienna?
If you have trouble getting a bolt to unlock, use pliers on the Allen wrench. First, remove the bolt on the side, unclip the wiring, then gently pull the long tube out of the hole. There is a 5/8th-inch socket specifically designed for spark plugs. This socket has a rubber lining which allows gripping and gentle installation.
Where do I go to change my spark plugs?
All Repco Authorised Service centres make sure to test all vital components like spark plugs in their safety checks. Contact your nearest Repco Authorised Service centre today to have your car back on the road and working efficiently. Do you know any other signs of when to change spark plugs?
How to change spark plugs on a Toyota Corolla?
How to change Spark Plugs on a 2003-2008 Toyota Corolla with the 1.8L engine. This is for the Corolla CE, Corolla LE and Corolla S. This is not for a Corolla XRS though. You can purchase your replacement spark plugs with the Amazon affiliate links below. Loading…
When to change spark plugs on Toyota Avalon?
Some can be a real bear to get at. As long as the Check Engine light doesn’t come on indicating a cylinder misfire, I’d service the spark plugs at the interval Toyota recommends. My 2003 Avalon (V6) I had them changed at 100k and regretted it afterward. The old ones looked like new.
When to change the spark plugs on a Toyota?
And read many posts that the Toyota service people said change the plugs at 30K miles. I found a Toyota spark plug pdf for 2011 that shows late 1990s and newer models of cars, trucks and suvs and about what spark plugs are used. It mentions iridium spark plugs last to 120K miles.
What do I need to replace a spark plug on a Toyota Corolla?
The tools needed to complete this procedure include a 10mm socket with a 1/4″ drive ratchet, a 5/8″ spark plug socket with an extension bar, a 3/8″ drive ratchet, anti-seize lubricant (optional), dielectric grease, and a spark plug gap gauge.
How do you remove an old spark plug?
Carefully insert the 5/8″ spark plug socket with an extension bar down into the top of the engine and over the old spark plug. Turn the ratcheting wrench counter clockwise to loosen and remove the old spark plug.
How much should I tighten my spark plugs?
If you have a torque wrench, the spark plugs should be tightened to 11 ft lbs if you applied anti-seize to the threads or 18 ft lbs if you did not apply anti-seize. Be careful to not over tighten the spark plugs, especially if you have applied anti-seize lubricant.
If you have trouble getting a bolt to unlock, use pliers on the Allen wrench. First, remove the bolt on the side, unclip the wiring, then gently pull the long tube out of the hole. There is a 5/8th-inch socket specifically designed for spark plugs. This socket has a rubber lining which allows gripping and gentle installation.
How do you change the battery in a Toyota Sienna?
While wearing gloves, use the 10-millimeter wrench to loosen the bolts on the battery. Carefully remove both sides and separate them from the battery, being extra careful not to touch both connections at the same time (otherwise you could get shocked). There should be a slight sizzling sound, which is okay.
Can you remove EGR bolts from turbo inlet pipe?
These EGR bolts are notorious for falling into the turbo inlet pipe. These are a total bitch to remove, but play around with different combinations of extensions, swivel joints/flex joints, stubby wrenches, etc, and find what works for you. Moving over to the passenger side…
How do you remove a rear spark plug?
This keeps the extension from accidentally pulling out of the spark plug socket. For the left rear plug, it was easier to get access by removing the bracket that holds a large bundle of wires and pushing them out of the way. There was also a ground wire that removes with a nut.
Where are the spark plugs on my car?
For the left rear plug, it was easier to get access by removing the bracket that holds a large bundle of wires and pushing them out of the way. There was also a ground wire that removes with a nut. This let me get my hand and arm in the left side enough to reach both the left and rear center plugs.
What kind of wrench do you use to change spark plugs?
4- and 8-millimeter Allen wrenches 10-, 12- and 14-millimeter sockets (the 10-mm will be used most often) Rubber spark plug socket (5/8 inches) 12- and 14-millimeter ratchet wrenches (makes things easier…) Small ratchet with extensions Standard and needle-nose pliers Hat (your hair will be brushing against the vehicle a lot)