How do you adjust headlights on a Subaru Outback?
Open your hood, locate the screws for horizontal and vertical modification of the headlights of your Subaru Outback (they are usually marked, and those on top must adjust the verticality and the one on the side handles the horizontality of the adjustment).
How do you adjust high beams on a Subaru?
To begin with, you’ll need to prepare your car to adjust your high beams in good conditions, here are the preparations to executed: Place your car on a surface in front of a white wall for example, about 4 or 5 meters from the wall. Check your tire pressure cautiously. . Try doing that with half a full tank.
What’s the best distance to back up a Subaru?
Then back your car up to a distance of between 7 and 10 metres. For the rest of the procedure here are the steps to stick to:
Open your hood, locate the screws for horizontal and vertical modification of the headlights of your Subaru Outback (they are usually marked, and those on top must adjust the verticality and the one on the side handles the horizontality of the adjustment).
Where is the low beam adjustment on a Subaru Outback?
The low beam adjustment is next to the low beam bulb in the rear. The driver side adj can be seen if look from the rear of the battery towards the front. The passenger side requires you to remove air intake piece which is quite easy. I would tread lightly making adjustments if you are not experienced.
Where is the adjustment nut on a Subaru Outback?
Take the battery completely out of the car. The adjustment screw/nut is silver in color and you can see teeth as part of the adjustment mechanism. The nut is horizontal, so you will need to approach the nut in this manner. The nut turns very easily and you will need to turn it more than you think to get any noticeable change in light aim.
What kind of wrench do I need for headlight adjustment?
The headlight adjustment bolt requires an 8mm wrench. For the driver’s side, I loosened the outer rod of the battery tie-down (10mm) and shifted the battery a few inches out of the way. This gives comfortable access to the 8mm adjustment screw with a ratchet (I used a 3″ extension, but a deep socket would work also).
How to adjust the low beams on a Subaru Outback?
First, these instructions are just for adjusting the low-beams on a 2011 outback 2.5 (I suspect it would be the same for a 2010). 1) park your car within 3 feet facing a garage door, make sure it is level. Turn on the lights (I would do this adjustment during the day to see everything better).
Where is the up / down adjustment on a Subaru Outback?
It has the small arrow marks with U and D on the black plastic bracket that goes back from the headlight housing, but it’s just a plastic retainer pin. The actual up/down adjustment for my 07 is on the back of the headlight housing. It’s a hex bolt with a wider metal ring (like a large, thick washer).
How to adjust your car’s headlights-AutoZone?
How to Adjust Your Car’s Headlights 1. Before adjusting your headlights, make sure the car is level. This means checking the tire pressure and removing any… 2. Now that the car is level, turn on the headlights. Just use the low beams, not the high beams or fog lights, as those… 3. Use a tape …
How to adjust the headlight on a Outback?
1) park your car within 3 feet facing a garage door, make sure it is level. Turn on the lights (I would do this adjustment during the day to see everything better). Mark the top of the beam with blue painters tape affixed to the garage door.
What kind of bulbs are in 2011 Subaru Outback?
Find direct-fit 2011 Subaru Outback headlight bulb replacements on this page and browse our selection to find high-beam or low-beam lights that will get you the visibility you need to drive confidently. We have halogen and HID bulbs, as well as ZXE bulbs that are made to shine as brightly as LED headlights.
First, these instructions are just for adjusting the low-beams on a 2011 outback 2.5 (I suspect it would be the same for a 2010). 1) park your car within 3 feet facing a garage door, make sure it is level. Turn on the lights (I would do this adjustment during the day to see everything better).
Where are the light adjusters on a 2011 Subaru Outback?
The 2011 has the black plastic tabs with “u” and “d” but they function only to fasten the light housings. Instead there are adjusters on the rear of the assemblies with 8mm heads on the ends and star wheels on the sides.
It has the small arrow marks with U and D on the black plastic bracket that goes back from the headlight housing, but it’s just a plastic retainer pin. The actual up/down adjustment for my 07 is on the back of the headlight housing. It’s a hex bolt with a wider metal ring (like a large, thick washer).
What happens if your headlight is on level ground?
If your lights cutoff line is higher than the bulb itself when measured from the ground you are hitting people in the face with your lights when on level ground which is bad. If you use an extension on your socket you do not have to remove the battery.