How do I log into my m2 bullet?

How do I log into my m2 bullet?

Login to the Bullet Router Open an Internet browser and enter the address: https://192.168.1.20. You will be taken to the airOS/Bullet Router login screen. Enter ubnt in the User Name field. Enter ubnt in the Password field.

What is m2 bullet?

Once connected this radio has the ability to provide a variety of network connectivity options including access point, client, or bridge configurations. Users also benefit from enhanced connectivity over long distances with data transfer rates of up to 100 Mbps or more.

How do I reset my ubiquiti m2 bullet?

To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. This 10/100 Ethernet port is used to connect the power and should be connected to the LAN and DHCP server.

How do I reset my ubiquiti M2 bullet?

How does Ubiquiti Bullet work?

The Ubiquiti Bullet series is a high powered 2.4GHz or 5.8GHz outdoor radio (denoted M2 or M5 respectively). With a cylindrical “bullet” shaped form factor, it’s designed to sit inline between an Ethernet cable input and a WiFi antenna output.

How do I reset my Ubiquiti Airmax?

Press the reset button on the device. While holding the reset button down, power the unit on. Wait 8 seconds then release the button (if you want to reset the unit to factory defaults, wait about 15 seconds or until the signal LEDs light up to indicate that the device is ready for recovery).

How do you set up an M2 bullet?

Verify connectivity in the airOS® Configuration Interface.

1. Make sure that your host machine is connected via Ethernet to the device.
2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168. x subnet.
3. Enter ubnt in the Username and Password fields. Select your Country and Language.

How do you pair a M2 bullet?

Configuring Android Devices

1. Settings -> Connections -> Wi-Fi.
2. Touch the Bullet’s WiFi network.
3. Check “Show advanced options”
4. IP settings -> Static.
5. IP address -> IP in the same range as the Bullet (e.g., 192.168. 10.207)
6. Gateway -> Same as specified in the “Network” tab (e.g., 192.168. 10.1)
7. DNS 1 -> 8.8. 8.8.

How do I find my Ubiquiti IP address?

How to find the IP address for your Ubiquiti access point?

1. Step 1: Download Ubiquiti locator. You can download the ubiquiti locator program here.
2. Step 2: Run the program. Once you have unzipped the file contents, click on the program file as outline in the picture below.
3. Step 3: Locate the IP address.

How do you reset a Ubiquiti Rocket m2?

Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the Rocket is already powered on. Power The Power LED will light green when the device is connected to a power source.

What is the IP address of the Ubiquiti bullet m2hp router?

Factory Default Settings for the Ubiquiti Bullet M2HP wireless router Top Ubiquiti IP Addresses 192.168.1.20 100%

How to configure your Ubiquiti bullet page 4 of 9?

Steps to Configure Your Ubiquiti Bullet Page 4 of 9 4. On the Network screen: Click on the Network Mode . Select outerR from the pull-down menu. In the LAN NETWORK SETTINGS section: Enter the IP Address you want for the Bullet. In this case 192.168.15.254 is entered. nnn.nnn.15.nnn was chosen to be outide most Park Wi-Fi schemes.

How to connect Ubiquiti to your host machine?

1. Make sure that your host machine is connected to the LAN that is connected to the Ubiquiti device (as shown on the previous page). 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet (e.g. 192.168.1.100). 3. Launch your web browser.

What’s the IP address for a Ubiquiti radio?

Default IP Address 192.168.1.20 Note: Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. TERMS OF USE: Ubiquiti radio devices must be professionally installed.