How can I tell if my blend door actuator is bad?

To test the blend door operation and too double check that you are changing the correct actuator motor turn the blower motor on and work the door in each way. You will be able to feel the air change temperature or vent level. Compare the bad actuator to the new unit.

What causes a blend door to get stuck?

What happens over time is that the blend door fails. it can either get stuck but most likely the blend door actuator has failed. In Aubery’s Case the Blend door in his F150 had failed in the hot position. With summer on the way we had to get the stuck blend door repaired. Loading…

What to do if your Honda Accord air vent is stuck?

Running a self-diagnosis can help identify the problem. To diagnose the problem, press the MODE (VENT/FLOOR) button several times. The LED should flash on and off as you press the button. Turn the ignition and the fan switch to the “OFF” position. Set the temperature control dial on Max Cool. Push the mode control button and select Vent.

What to do if your heat blend door stops working?

Heat blend door stopped working. Bought a new actuator at the dealership. Installed myself by splitting the panel on the driver’s side bottom and removing a zillion screws, then popping the panel loose. R&R’ed the actuator and put it all back together. The normal method is to remove the entire dashboard and metal framing.

Why is my Blend door actuator stuck on 1 mode?

Also when finished cleaning them ensure that there is enough contact “pressure” by bending the contacts slightly upwards so that they will be exerting pressure on their mating contact when the cover is replaced, thereby ensuring a good connection Here’s an image to show where I mean.

How much does a blend door actuator cost?

The dealership wanted about $300 for the part. Ebay has them used for about $90. I checked my local pull-a-part and saw that 2 2000 Honda Accord’s had been brought in in the past couple weeks. After checking about 6 cars in the yard, I found a car that clearly didn’t have the original control module installed.

What kind of control motor does Honda Accord have?

I checked my local pull-a-part and saw that 2 2000 Honda Accord’s had been brought in in the past couple weeks. After checking about 6 cars in the yard, I found a car that clearly didn’t have the original control module installed. The plastic was a bleach white compared to my original which was a discolored yellow. And it felt more sturdy.

What makes up a blend door actuator motor?

A blend door actuator is made up of an electric motor that turns a plastic gear set in one direction or another which is connected to an air control door pivot at the final drive of the unit.

What to do if your blend door blower is stuck?

If the door is stuck the heater plenum with need to be removed and the problem resolved before installing the new unit. To test the blend door operation and too double check that you are changing the correct actuator motor turn the blower motor on and work the door in each way.

Why does my Blend door not turn on?

Since this is just a small electronic part, this won’t be unheard of. If that happens, the blend door won’t work, and it’s likely your temperature will just be stuck on one setting with no ability to adjust the intensity up and down, or alternate between things like the lower vents or the defroster.

Why does my Blend door open when the AC is on?

If the AC is turned on, the temperature of the cold air can be altered with the temperature control. That control commands the blend door actuator to open or close partially or fully to allow air from the heater core to mix with the cold air from the AC evaporator.

What kind of motor does a blend door use?

The blend door is controlled by a blend door actuator, which can be a cable or an electric motor. The blend door is also referred to by some car makers as an air mix door. Both terms mean the same thing. Here’s a diagram of a typical heating system in a vehicle.

Why is the actuator called a blend door?

The blend door, which the actuator controls, is what diverts and controls the flow of air. There should be controlled by some plastic gears that are responsible for moving the blend door where the actuator sends the correct signals. The blend door is called a door because it really is just a flat panel of plastic.

Is there a problem with my Blender actuator?

Knocking: This is an unusual symptom, but if you’re experiencing this, it’s almost definitely a problem with your blender actuator. When you start the car, or just the AC system, and notice a knocking sound like someone tapping on your door, that is indicative of a problem with the blend door actuator.

Can a heater be removed from a blend door?

A blend door actuator is made up of an electric motor that turns a plastic gear set in one direction or another which is connected to an air control door pivot at the final drive of the unit.

How does an air blend door actuator work?

An air blend door actuator is constructed from a plastic housing, a small electric motor and a plastic gear set. A door position sensor is also incorporate into the unit to send feed back information to the climate control computer.

How does the blend door actuator work in a car?

The blend door actuator is a small electric motor that features sensors connected to your car’s climate control system. As you adjust the temperature up and down, or the intensity of the air flow, the signals go through the actuator.

Is there a recalibration procedure for auto HVAC?

If you have auto HVAC controls you would need to use the radio fuse instead of the ecas fuse to initiate the recalibration process. If you have manual controls there is no recalibration procedure available according to GM service information. If you need more information, it is much easier to carry on a discussion in the Ask a Question section.

Navigation