Do you have to torque your rod bolts?
Torqueing your rod bolts without pre-determining the required torque to achieve the correct rod bolt stretch is not recommended. However if this is the only tightening method available to you, DO NOT EXCEED THE TORQUE AMOUNT INDICATED FOR YOUR BOLTS. NOTE: Your Crowerods are totally rebuildable.
How to determine the torque of a connecting rod?
STEP 1: Your Crower connecting rods came with a connecting rod specification tag. Check the tag to find the rod bolt part number used to fasten your connecting rods. Rod bolt length listed here is the measurement from under the head to the end. STEP 2: Use the chart below to determine the recommended lubricant, rod bolt stretch and torque amounts.
Where do I find the rod bolt part number?
Check the tag to find the rod bolt part number used to fasten your connecting rods. Rod bolt length listed here is the measurement from under the head to the end. STEP 2: Use the chart below to determine the recommended lubricant, rod bolt stretch and torque amounts.
Torqueing your rod bolts without pre-determining the required torque to achieve the correct rod bolt stretch is not recommended. However if this is the only tightening method available to you, DO NOT EXCEED THE TORQUE AMOUNT INDICATED FOR YOUR BOLTS. NOTE: Your Crowerods are totally rebuildable.
STEP 1: Your Crower connecting rods came with a connecting rod specification tag. Check the tag to find the rod bolt part number used to fasten your connecting rods. Rod bolt length listed here is the measurement from under the head to the end. STEP 2: Use the chart below to determine the recommended lubricant, rod bolt stretch and torque amounts.
Check the tag to find the rod bolt part number used to fasten your connecting rods. Rod bolt length listed here is the measurement from under the head to the end. STEP 2: Use the chart below to determine the recommended lubricant, rod bolt stretch and torque amounts.
How to change the front wheel hub on a Nissan Altima?
1. Cotter pin 2. Disc rotor 3. Wheel hub and bearing assembly 4. Splash guard 5. Steering knuckle 1. Remove wheel and tire from vehicle. Refer to WT-66, “Adjustment”. 2. Remove brake caliper using power tool, leaving brake caliper hydraulic lines connected.
How to adjust GM 3400 3.4L pushrod rocker arms?
Intake valves are closer to the valley of the engine. No compression on 3.4 V6 Aztec, replaced one cylinder head only but did remove push rods etc from both to replace gaskets, also turned the engine over without push rods good compression, left overnight still no compression any one have any ideas I am stumped. Lifters?
What are the torque specs on a Pontiac?
Torque Timing Cover to Intake Bolt first, THEN torque remaining Intake Manifold Bolts
What should the torque be on MGP connecting rods?
Once clean and dry and installed in the engine, lubricate the threads of each rod bolt with 50W motor oil (brand does not matter as long as it is 50W) and tighten until the head of each fastener just contacts the hat washer in the cap. Slowly and steadily torque each fastener once to the specified torque value listed below.
Do you need torque for K1 rod assembly?
K1 Technologies does not recommend the use of or provide torque values for tightening bolts. The stretch method or the torque and angle method are both much more accurate ways to properly tighten rod bolts.
How do you Torque a roller lifter rod?
Using the above table, torque the rod bolts to achieve the required amount of stretch for your application. Record this torque spec as this is the exact torque spec that you will be using to install your rods in the motor.
What are the specifications for Crower connecting rods?
Please read this entire page before starting to install your rods. STEP 1: Your Crower connecting rods came with a connecting rod specification tag. Check the tag to find the rod bolt part number used to fasten your connecting rods. Rod bolt length listed here is the measurement from under the head to the end.