Can you remove the slave cylinder from a Saturn clutch?

Remove the clutch slave cylinder. Do NOT disconnect the hydraulic lines. The Saturn clutch hydraulics are a closed system and are not meant to be serviced. If you accidentally pull one of these lines you will need to buy new hydraulics from Saturn. Do NOT step on the clutch with the slave cylinder removed.

How do you replace a clutch master cylinder?

Step 1: Install entire system. Very carefully, install the entire system (clutch master cylinder, hydraulic line, and slave cylinder) down through the engine compartment. Warning: Do not bend the hydraulic line as it will break. Step 2: Install the slave cylinder.

Where is the clutch slave cylinder located on a clutch fork?

A clutch slave cylinder is a member of the clutch system that provides leverage assistance to the clutch fork. The clutch slave cylinder operates just like a hydraulic cylinder on a boom lift. The cylinder is connected to the clutch master cylinder located on the firewall next to the brake master cylinder through a hose.

Where is the clutch slave cylinder on a boom lift?

The clutch slave cylinder operates just like a hydraulic cylinder on a boom lift. The cylinder is connected to the clutch master cylinder located on the firewall next to the brake master cylinder through a hose.

Where is the clutch on a Saturn s?

On the top of the transmission is the upper locator bracket/mount. It connects the transmission to one of the two ‘dogbone’ style motor mounts. Remove the two bolts that secure the bracket to the transmissions and lift it up out of the way.

Do you need a Haynes Manual to replace a Saturn clutch?

These instructions are a conglomeration of several other how-to documents, Saturn FSMs, shop manuals, online postings and other sources of information. These instructions should not be considered a stand alone document and should be used in conjuction with an FSM, Haynes, or Chiltons manual.

How do you Bleed the clutch on a Saturn Vue?

Bleed the clutch of the Saturn VUE if filling the reservoir doesn’t improve your clutch’s performance. You may have air bubbles in the lines. Attach one and of a rubber hose to the bleeder valve of the slave cylinder (near the clutch housing), and put the other into a clear container that holds clutch fluid.

Where is the nut on a hydraulic clutch?

First, locate the clutch master cylinder body. Follow the metal tubing coming from the rear of the clutch master cylinder body. It will turn into flexible hosing as it connects to the slave cylinder. Inside this piece is a seal, piston, rubber boot, push rod, locking nut, and adjustable nut.

Where are the shifter cables on a Saturn s?

Disconnect the shifter cables from the shifter tower and remove them from the transmission bell housing. The cables are attached to the shifter tower by small clips that should just slide off.

How big should the clutch be on a Saturn s?

Much easier if you have a hoist to run the car up and down. Assuming that you don’t so try and get the car as high into the air as you can, SAFELY OF COURSE. 15-18 inches between the rear subframe and the floor is probably a good compromise.

Why does my Saturn 104k not start up?

My ’97 Saturn (104K) starts well in the morning. I drive home everyday about noon. When I try to start it, it cranks, and will eventually start, but it takes a good 8 to 10 seconds to get it going. The weather is hot when I have these problems, not sure if this has anything to do with it. Any thoughts?

Why does my 1996 Saturn SL2 not start?

The battery in my 1996 SL2 discharged because the car was sitting for several months unused (I know, I know — I should have disconnected the battery!). So I recharged it (pretty sure, anyway). Now the lights come on, etc. but when I turn the ignition the car cranks for about 1 second then stops cranking and there is a loud rapid clicking noise.

How tall is the clutch socket on a Saturn?

– 30mm Tall Socket – Some sort of engine support – Saturn shop manual with torque specifications Much easier if you have a hoist to run the car up and down.

Where are the clutch cables on a Saturn FSM?

The cables are attached to the shifter tower by small clips that should just slide off. To disconnect them from the bell housing just pull back slightly and then lift through the slot. (There is an excellent diagram in the Saturn FSM if you have one.)

What are the symptoms of a failed clutch slave cylinder?

If your car has this issue you can expect to see the following symptoms: One of the commonest symptoms of a failed clutch slave cylinder is also one of the easiest to spot – you’ll notice that the clutch pedal feels ‘soft’ as you drive.

Where is the PCM on a Saturn’s series?

On newer S Series you will need to disconnect the PCM (square silver box behind the battery). If you have never removed the battery tray there is one bolt that is accessed from the drivers side wheel well. Don’t do what I did and just rip it out.

Can a clutch be replaced in a car?

This is not the easiest method for replacing a clutch but it does allow you to do it with the engine in the car and without a needing an alignment afterwards. Previous to this the most complicated things I had done were brake pads and rotors, valve cover gasket, and a radiator.

What are the symptoms of a bad clutch master cylinder?

Symptoms of a Bad or Failing Clutch Master Cylinder 1 Low or dirty clutch fluid. 2 Hard to shift. 3 Abnormal clutch pedal behavior.

What causes a clutch on a car to not release?

If this is the case the clutch will often stick. The cable will need to be replaced. Clutch Will Not Release: There are many things that can cause a clutch to not release. Everything from the damaged input shaft splines to a worn bearing retainer to a bent clutch disk.

Why does the clutch pedal make a squealing noise?

Now, with the engine running, depress the clutch pedal just enough to remove the free play, to the point where you feel you need to apply force to the pedal to push it down further. You may need to push the pedal a little more. If you hear a squealing noise, you may have a worn out release bearing.

Where can I buy Saturn parts for my car?

RockAuto ships auto parts and body parts from over 300 manufacturers to customers’ doors worldwide, all at warehouse prices. Easy to use parts catalog. SATURN Parts | RockAuto

Why does my car make a grinding noise when I release the clutch?

If you hear a squealing noise, you may have a worn out release bearing. Fully depress the clutch pedal to release the clutch. If you hear a whirring sound then, you probably are dealing with a bad pilot bearing. A bad synchronizer can cause a grinding noise.

What do I need to replace clutch master cylinder?

Replacing the clutch master cylinder requires common tools and basic automotive repair knowledge. Disconnect the negative battery cable from the vehicle battery. Pry off the clutch pedal push rod, retaining pin and bushing, using a flat-head screwdriver.

Where are the retaining nuts on a new clutch?

Insert the two retaining nut studs on the new clutch master cylinder through the firewall, in the engine compartment. Place the master cylinder bracket onto the master cylinder studs inside the vehicle. Install the two retaining nuts onto the master cylinder studs. Tighten the nuts, using a socket wrench and socket.

How do you put a slave cylinder in a clutch?

Install the slave cylinder in the clutch housing with the hydraulic lines facing down and rotate the cylinder a quarter-turn clockwise as you push it into the clutch housing. Apply silicone grease to the clutch pedal retaining pin and connect the push rod to the pedal.

How to replace clutch master cylinder on Toyota Corolla?

How to Replace a Clutch Master Cylinder on a Toyota Corolla Use a wrench to disconnect the Corolla’s battery at the negative cable and terminal. Use a screwdriver to unscrew and remove the knee bolster below the steering column. Disconnect the pushrod on the clutch pedal, removing the clip on the clevis pin and then removing the pin itself.

Navigation