Can you put a 007 valve in a Honda Civic?
The .007 should slide in with a slight drag on the intake side. But the .008 should not be able to fit. If it does, insert the .007, loosen the lock nut with the jam nut tool and turn the screw gently using two fingers.
What should Valve clearance be on Honda Civic SOHC?
All the valves for a particular cylinder will be at rest when that cylinder is at tdc on the compression stroke. Check the valve clearance on cylinder 1 (closest to crank pulley). Use your .007 feeler gauge on the intake side and the .009 on the exhaust side. The .007 should slide in with a slight drag on the intake side.
Do you need a timing light for a Honda Civic?
This article applies to the Honda Civic (1990-2000). In order to keep your Honda running great, the ignition timing has to be set properly. Symptoms of poorly-set timing include engine pinging, running rich, or running lean. To successfully get this job done you will need a timing light. You can purchase or borrow one.
Is there a problem with my Honda Civic?
I have a 97 Honda Civic with 233K miles on it. I recently had my state inspection done and the mechanic noted my fuel and brake lines were starting to rot, but not leak. Is this a problem that needs immediate addressing, or can I wait until “symptoms” start to appear.
This article applies to the Honda Civic (1990-2000). In order to keep your Honda running great, the ignition timing has to be set properly. Symptoms of poorly-set timing include engine pinging, running rich, or running lean. To successfully get this job done you will need a timing light. You can purchase or borrow one.
What does BTDC stand for in Honda Civic?
BTDC stands for “before top dead center.” If you deem it necessary, you will have to adjust the distributor cap in order to advance or retard the timing. You need to turn the distributor housing towards the firewall to advance the timing and turn towards the front end to retard the timing.
Where is the ignition button on a Honda Civic?
It is underneath the glove box by the kick panel. It’s the same connector used to read check engine lights. You need to disconnect it and put a small wire connecting both sides of the connector in order to short it. You want to do this so the computer doesn’t try adjusting after you do your own adjustments.
Where is the service connector on a Honda Civic?
The service connector is located on the passenger side. It is underneath the glove box by the kick panel. It’s the same connector used to read check engine lights. You need to disconnect it and put a small wire connecting both sides of the connector in order to short it.
How often do you change the valve lash on a Honda Civic?
According to the manual, you should adjust the valves every 12 months or 15,000 miles. You will also need to perform a valve adjustment if you loosen the head bolts for any reason (ie mini-me or headgasket change), change the cam, or disassemble the valvetrain. Feeler Gauges .007, .008, .009, .010
What’s the firing order for Honda Civic SOHC?
The firing order is 1, 3, 4, 2. Turn the crank pulley until the cam pulley turns 90 degrees counterclockwise. The “UP” etch mark will face the front of the vehicle. Check/adjust the valves. Cylinder #4 Valve Clearance Next is #4. The “UP” etch mark will face downward. Check/adjust the valves. Cylinder #2 Valve Clearance
The .007 should slide in with a slight drag on the intake side. But the .008 should not be able to fit. If it does, insert the .007, loosen the lock nut with the jam nut tool and turn the screw gently using two fingers.
All the valves for a particular cylinder will be at rest when that cylinder is at tdc on the compression stroke. Check the valve clearance on cylinder 1 (closest to crank pulley). Use your .007 feeler gauge on the intake side and the .009 on the exhaust side. The .007 should slide in with a slight drag on the intake side.
The firing order is 1, 3, 4, 2. Turn the crank pulley until the cam pulley turns 90 degrees counterclockwise. The “UP” etch mark will face the front of the vehicle. Check/adjust the valves. Cylinder #4 Valve Clearance Next is #4. The “UP” etch mark will face downward. Check/adjust the valves. Cylinder #2 Valve Clearance
According to the manual, you should adjust the valves every 12 months or 15,000 miles. You will also need to perform a valve adjustment if you loosen the head bolts for any reason (ie mini-me or headgasket change), change the cam, or disassemble the valvetrain. Feeler Gauges .007, .008, .009, .010
What’s the firing order for a cam pulley?
The firing order is 1, 3, 4, 2. Turn the crank pulley until the cam pulley turns 90 degrees counterclockwise. The “UP” etch mark will face the front of the vehicle. Check/adjust the valves.
Can a crankshaft pulley be removed from a Honda Civic?
The crankshaft pulley bolt is one of the most stubborn bolts on this era of Honda. Unfortunately, they also need to come off in order to remove the crankshaft pulley and the crankshaft seal behind it. Typically this is done in order to change the timing belt, but the crankshaft pulley itself will fail on its own as well.
How do you jack up a Honda Civic?
Use a two-post lift if that’s an option. If it’s not and you’re doing this in the driveway, just set the car up on jack stands. Remove the passenger’s side wheel. The crankshaft pulley is the single, large pulley at the bottom of the engine. Figure 1. Diagram of the jacking points. (Related Article: How to Jack Up Your Civic – Honda-Tech.com)
How can you tell if a Honda Civic is dying?
Most of the time you can tell it’s dying by a constant squeal from the front of the motor that rises and drops with engine’s rpm. Also, the front crankshaft seal can be prone to leaking if it’s old or if it has been reused at any point. As much as a hassle this might be, the truth is it can be done at home as long as the right tools are used.
Can a crankshaft seal be replaced on a Honda Civic?
Also, the front crankshaft seal can be prone to leaking if it’s old or if it has been reused at any point. As much as a hassle this might be, the truth is it can be done at home as long as the right tools are used.