Why is my air conditioner clutch not working?

If your Air Conditioning compressor isn’t working (the clutch won’t engage) then watch this video. The A/C switch on the dash switches the compressor on, with one exception. If the PCM (powertrain control module) senses low pressure in the low pressure fluid line, it will stop the compressor clutch from engaging to prevent any damage.

What causes an AC compressor to not engage?

If the clutch doesn’t engage, the problem could be a blown fuse, an open in the wire to the clutch coil, a bad clutch coil, a poor ground, or a low pressure lockout. AC compressor clutches receive power in a number of ways. They can activate through a relay that’s energized directly by a proper condition of the low and high pressure switches.

Why is the clutch not engaged on my gas compressor?

But if the system is low on refrigerant, the clutch will never engage. Some DIYers then hotwire the low pressure switch to force the compressor clutch to engage while they recharge. BAD MOVE. At that point you’re running the compressor with little to no oil.

When do I Turn Off the a / C, the clutch stays engaged?

A/C compressor doesn’t cycle off. Clutch stays engaged when turned on. I noticed my A/C compressor stays engaged when I turn the A/C on. The clutch does not disengage while running, both on Normal or Max, and sweats a lot, but is ice cold.

Why does my AC clutch not engage?

Why AC clutch won’t engage. If the clutch doesn’t engage, the problem could be a blown fuse, an open in the wire to the clutch coil, a bad clutch coil, a poor ground, or a low pressure lockout. AC compressor clutches receive power in a number of ways.

How can I tell if my AC clutch is engaging?

Listen for any internal buzzing or clicking from the clutch. If the clutch fails to engage and spin, but you hear electrical buzzing or clicks inside, it indicates an internal clutch short. Listen for excessive bearing noise coming from the clutch or compressor.

Why won’t my a/C compressor clutch engage?

A compressor clutch that won’t engage can be caused by a lot of different issues, from a low refrigerant level to a blown fuse.

How do you replace AC compressor clutch?

How to replace an AC Compressor Clutch. To remove the clutch, screw in the removal tool and hold the clutch disc with the holding tool. Remove retaining nut on the compressor shaft while holding the clutch disc with the holding tool. Then install the clutch disc puller.

Why is the a / C not engaging on my Honda Civic?

This lack of any noticeable additional load and the fact that the A/C operated beautifully for the first 230km of the trip makes me suspect the compressor clutch isn’t engaging for some reason. Does this seem like a reasonable guess, how can I verify this, and what are my repair options?

How can I tell if my Honda Civic clutch is engaged?

It will be labeled Mag Clutch or have a picture of a snowflake. Then swap it with one of the same part number in the same box. Then test to see if the compressor engages. Your “I feel the load” test is fine but you can see the clutch come on by watching the clutch end plate on the end of the compressor.

Why is the clutch not working on my Honda Accord?

In a few cases, the clutch does not engage due to a clogged refrigerant circuit. Set all air conditioning controls to the MAX before kicking off the engine. Check the front side of the clutch to examine its condition. Also, find out whether the clutch and the pulley are spinning.

Why is the clutch not engaging on my Honda Civic?

I followed the “clutch not engaging” flowchart in the Civic WSM which is basically: Thanks for contributing an answer to Motor Vehicle Maintenance & Repair Stack Exchange! Please be sure to answer the question. Provide details and share your research! But avoid …

What to do if your air conditioner clutch does not engage?

If the clutch doesn’t engage, the air conditioning compressor can’t pump refrigerant. So start your diagnosis by determining if the compressor clutch works. Turn the air conditioning controls to MAX AC and start the engine. Then look at the front of the compressor clutch.

Is the a / C on my Honda Civic working?

I have a 2000 Honda Civic 1.6L iSR MTX that I bought recently and replaced the engine in. Haven’t driven it much, but got the impression the A/C was not working so well. However, I took it on a long trip recently, and on the first 230 kilometers the A/C worked beautifully.

Why is my air conditioning not working on my Jeep Liberty?

Dana Dowling/Demand Media The air conditioning system in your Jeep Liberty compresses a refrigerant and blows the resulting cold air into the passenger cabin. When this system is not working properly, it can be because the pressure in the AC lines is too low, or because the compressor has failed.

What to do when Clutch won’t engage?

So you need to use a paper clip to bypass the relay switch and force the clutch to engage. You can then recharge the freon and re install the relay switch and it will sense more pressure and the clutch will engage by itself. Loading…

Why does the clutch not engage in a low pressure car?

If the PCM (powertrain control module) senses low pressure in the low pressure fluid line, it will stop the compressor clutch from engaging to prevent any damage. This is because low pressure = low fluid, and r 134a is also oil/lubricant for the compressor and if you don’t have fluid then you will damage the compressor.

Are there any Jeep Liberty clutch left in stock?

Only 9 left in stock – order soon. . . Only 1 left in stock – order soon. . Only 15 left in stock – order soon. . Only 12 left in stock – order soon.

Where is the air conditioning line on a Jeep Liberty?

The air conditioning lines will be steel lines running on the left side of the engine bay. The low pressure line on your Liberty is marked with a blue valve cap on the line. Unscrew the blue valve cap and screw on the air conditioning pressure gauge. Turn the knob on the pressure gauge counterclockwise to allow pressure into the gauge.

How is the clutch connected to the AC unit?

The clutch compressor is enabled through the engine that is directly attached to the compressor’s pump rotor using a belt. However, most car AC systems now use an electromagnetic clutch piece that engages the compressor to spin the air conditioning unit.

Why does my AC compressor clutch not engage?

Why AC clutch won’t engage If the clutch doesn’t engage, the problem could be a blown fuse, an open in the wire to the clutch coil, a bad clutch coil, a poor ground, or a low pressure lockout. AC compressor clutches receive power in a number of ways.

What should you do if your AC clutch is not engaging?

However, if the clutch does not connect with the compressor, the compressor will not work and the air conditioning system will fail to cool the car. Try checking if the clutch is in good condition by applying these steps: Turn the AC controls to maximum air conditioning.

Why is the AC clutch not engaged when the Freon is low?

No, the AC clutch will not engage when the Freon is empty or low. The low-pressure switch will prevent the AC clutch from being engaged, and the compressor will not spin. This prevents the compressor from engaging. The major reason the Freon is low would be due to leakage.

What happens if you dont use the clutch switch?

Without the cycling switch to activate the compressor’s clutch, the AC system will not be pressurized correctly, and the system will be unable to produce any cold air as a result. If you begin to notice that the AC system is no longer functioning as it used to, and you suspect that the clutch cycling switch may have a problem,…

When to close the AC clutch cycling switch?

When it is detected that the pressure has dropped below a certain threshold, the switch will activate allowing pressure from the high pressure side of the AC system to enter the low side and equalize the pressure. When the pressure returns to normal, the cycling switch will close.

Where is the clutch on an AC system?

It is mounted in the low pressure side of the AC system and its purpose is to detect the flow of refrigerant in the system by measuring the pressure.

What happens if the clutch on the AC fails?

No cooling at all In more severe cases, where the switch has completely failed, your AC system will completely cease to blow cold air. Without the cycling switch to activate the compressor’s clutch, the AC system will not be pressurized correctly, and the system will be unable to produce any cold air as a result.

How does an AC compressor clutch receive power?

AC compressor clutches receive power in a number of ways. They can activate through a relay that’s energized directly by a proper condition of the low and high pressure switches. Or, the relay can be operated by the PCM which has interpreted the condition of the low and high pressure sensors.

Why is my Mercedes-Benz E320 AC not working?

Learn if it’s a simple fix or time to seek out a trusted technician. Not your vehicle? Why Isn’t My A/C Working? What are common reasons my Mercedes-Benz E320 has air conditioning problems?

How to troubleshoot a / C compressor clutch problems on your Mercedes?

This video is helpful if you are trying to troubleshoot air conditioner problems, the A/C compressor clutch in particular. This opens in a new window. Start by turning the engine on. Set the AC to maximum cold setting. Open the hood and look at the serpentine belt to locate the AC compressor.

Why is the clutch not engaged on my Mercedes?

Remember that the A/C clutch is controlled by the A/C Control Unit. If that unit detects an error it will not engage the A/C compressor to avoid it getting damaged. One other reason why the A/C compressor does not engage is the fact that the system may be low on R134 refrigerant.

Why is the clutch not working on my air conditioner?

Now look at the pulley of the air conditioner compressor. The center part (the clutch) should be engaged and should be spining along with the pulley. The center part on the pulley of the A/C compressor will not spin when you have the air conditioner off or if there is a problem.

Learn if it’s a simple fix or time to seek out a trusted technician. Not your vehicle? Why Isn’t My A/C Working? What are common reasons my Mercedes-Benz E320 has air conditioning problems?

I just bypassed the ac clutch relay with a paper clip and got the ac clutch to spin, but it’s still blowing hot air. Has anyone else had similar problems or have any advice? It’s getting hot out in New York! Is the car not under warranty anymore? There’s most likely a body controller code not allowing your clutch to engage for some reason.

Why is my AC unit not turning on?

The reason breakers trip could be due to using too many appliances at once, or maybe an appliance is too old and consumes too much electricity. Regardless of the reason, if the breaker that provides power to your AC unit trips, the air conditioner won’t turn on. Check to see if you need to reset a breaker.

How to test for AC compressor clutch function?

Test for AC Compressor Clutch Function. Knowing when your AC compressor is running or not is critical to diagnosing the AC system, but also for charging the system. Reading the low side pressure must be done when the compressor is running. In this video, you’ll learn to do both. Drop me a postcard or send me a license plate from where you are!

Why is there no power to the a / C compressor?

Potential Causes: A/C Compressor, A/C Pressure Sensor F129, A/C Switch, Ambient Temperature Switch F38, Battery Auxiliary Fuse Box, Fan Control Module J293 (and Wiring), Fuse or Lost Throttle Basic Settings Test the Fan Control (FCM) module inputs as follows: 1.

Is the a / C clutch in the ECU?

If the ECU is seeing the signal from the A/C switch and commanding the fans on it should also be comanding the compressor on. Thats the Red/Blue wire. since that all checks good the open has to be in the ECU. Ok, what about this A/C diode?

Why does my a / C CLUTCH not engage?

A/C clutch will not engage. I narrowed it down to the red/blue wire on the compressor relay. The relay is good. My There is a way to pinpoint it.

Why is my AC not working in my GMC?

Please try again later. If you have a car made by GM such as Chevrolet, Cadillac, Buick, GMC, and Pontiac and your AC does not blow cold air and the A/C Compressor is not engaging it does not mean for sure that you have bad ac compressor or bad ac clutch coil, or low on freon, it also could be a bad ac pressure switch.

What to do if your AC unit won’t turn on?

If your AC unit won’t turn on, here are the 6 most common reasons why and what to do. If your AC unit won’t turn on, the first thing you should check is if there was a blown fuse or a tripped breaker. There’s a good chance that the problem is a tripped breaker if the circuit was overloaded.

What should I do if my AC compressor is not working?

There are 3 things that you should check, in a specific order, to narrow down the problem. You should check your refrigerant levels first, then you should check the electrical components that are connected to the compressor clutch, and finally you should check the actual mechanical components of the compressor clutch.

What was the problem with my Nissan Altima A / C?

Had a/c problems about a year ago. A/c would intermittently work. Pretty bad during daytime operation. Anyways took it to local mechanic. He said the compressor was on its way out. 30 seconds later his helper comes out and says he got it working.

What kind of compressor does Nissan Altima have?

Your altima has a variable displacement compressor, the 4th gen is an on/off clutch. It is a common for the solenoid that controls displacement to fail stop working.

Is the AC on my 2015 Altima working?

I bought an altima 2015 SV 2.5 last week and I am noticing that the AC sometimes does work and sometimes it doesn’t I took it to Jiffy Lube and they checked the pressure, oz of Freon, etc. Additionally they vacuumed the system and recharged…

Why is the AC compressor clutch not engaging?

I have done some preliminary diagnosis on it and could use some advice. The compressor clutch is not engaging no matter how long I watch it on a 70 degree day with AC set to max. I have verified the controls are moving the actuators on the blend door and the blower is changing speed ect…

Is there an issue with my Nissan Altima clutch?

(Playback ID: TyRd9Qs-MDlW_flE) An error occurred while retrieving sharing information. Please try again later.

What to do if your a / C compressor won’t engage?

HOWEVER, if you cannot turn the compressor on, you cannot recharge your AC levels (grrrr). So you need to use a paper clip to bypass the relay switch and force the clutch to engage. You can then recharge the freon and re install the relay switch and it will sense more pressure and the clutch will engage by itself. Loading…

Why is the AC compressor on my Nissan club not working?

OP — “compressor not working.” “i check the hi side and the low side pressure. the low side was about 70 it’s too hi and the hi side was 130 i connect a wire from my vehicle battery direct to the ac compressor s wire to jump it but nothing happened not engaged !”

Why is my a / C not working on my Nissan Altima?

The switch simply cuts the power circuit to clutch off. There was no need to refill either, I’m betting the one wire if right there at compressor was the clutch power lead and simply cut or broken would stop clutch from coming on. Fixing that wire alone would have the a/c back to working instantly.

What’s the air pressure in my Nissan Altima?

My car is 2014 Nissan Altima S 2.5L. I measured pressure with ac harbor freight ac manifold gauge and AC Low side is closing extremely high closing the meter gauge at over 350 psi (low side) and Hi side is 125 psi which is low as it should be around 225-250psi and that is with outside temp at 85F.

How to manually engage AC compressor clutch, the easiest?

There is no need to switch on the air conditioning system for this method to work. Tips – You should route the jumper wire to avoid it getting tangled or interfering with other moving components. It is an ominous sign when the clutch engages but the compressor does not spin. Changing the compressor clutch could be the only solution in this case.

How to tell if your a / C compressor clutch is working / engaging?

If there are error codes on the A/C Control Unit the compressor will not engage and you will need to reset the fault codes using a diagnostic scanner such as the Launch Creader or iCarsoft MB II. How to tell if your air conditioner AC compressor clutch is working / engaging?

How is the compressor clutch relay turned on and off?

In some vehicles the compressor clutch relay is turned on and off by the low pressure switch and the evaporator temperature sensor. In a computer controlled system, the compressor clutch relay is grounded by the computer. If the fuse is good, disconnect the electrical connector from the compressor clutch coil.

How can I tell if my compressor clutch is working?

So start your diagnosis by determining if the compressor clutch works. Turn the air conditioning controls to MAX AC and start the engine. Then look at the front of the compressor clutch. Both the pulley and the clutch should be spinning. That means the clutch has properly engaged with the pulley.

(Playback ID: TyRd9Qs-MDlW_flE) An error occurred while retrieving sharing information. Please try again later.

What happens when the AC clutch does not work?

An automobile can have numerous serious problems and a dysfunctional AC compressor clutch is one of them. When this component does not work properly, the engine does not get the cold air flow – leading to some major complications. Knowing how to manually engage AC compressor clutch will help you skip a visit to the mechanic.

What does it mean when your AC compressor does not spin?

It is an ominous sign when the clutch engages but the compressor does not spin. Changing the compressor clutch could be the only solution in this case. A bad AC compressor clutch needs immediate fixing. A delay can cause serious damage to the air conditioning system and the engine.

How can I Check my AC compressor clutch?

Use a digital voltmeter to measure the ground and voltage of the battery at the detached connector cable. Go on to check the fuse if you cannot read the voltage readings. Move on to the clutch relay if the fuse turns out fine.

Are there any problems with the Volkswagen Beetle?

There are a few problems when it comes to stopping there is a weird noise which I believe comes from the spoiler that comes out when needed and the lowers back into the car when not needed. They tend to go through coolant quickly but its a super easy 2 minute fix. Also…

Navigation