Why does the starter turn when hooking up battery?
Verified ignition in the locked position and left keys out of ignition. Again, when I touched the negative battery cable to the negative terminal on the battery, the starter engaged and tried to start the motor. Could the battery be bad?
Why does my Ford starter keep turning over?
Sometimes a Ford solenoid will “weld it’s contacts together” . In this case the starter will keep turning the engine over even after you have released the ignition switch from the “start” position. Sometimes the only way to stop it is to remove one of the battery terminals!
What causes a starter to turn off without a key?
At starter the smaller exciter wire is either getting voltage or the solenoid is stuck engaged?? Smaller gauge wire should have no power without key in “start” position but if it can get power from anywhere it will trigger the starter. Look again to see if something is touching or too close there.
When to know if your car starter is bad?
> If you get a single loud click and all power goes off in the car (lights, radio, everything: like you took the battery out of the car) then you just have a loose or dirty battery terminal or connection. If you get multiple rapid clicks when you turn the ignition key to “START” you probably don’t have a bad starter.
Why does my car starter keep running when I Turn Off the key?
If that switch doesn’t disengage when you let off the key and go to run or off position, your starter motor will run til the cows come home, or at least till the batt goes dead or the starter burns up as these motors are made for strictly intermittent use. This is because if the switch is stuck the starter drive stays engaged also.
Why is my key stuck in the ignition?
If the key is stuck in the start position, this is a ignition lock cylinder issue and the reason the starter continues to turn the motor over. If the starter is turning but the motor is not, then the starter is likely the problem.
Verified ignition in the locked position and left keys out of ignition. Again, when I touched the negative battery cable to the negative terminal on the battery, the starter engaged and tried to start the motor. Could the battery be bad?
What should I do if my car starter is still cranking?
When you release the key to the run position the voltage should go to zero. If it still has the problem something is powering the starter without the solenoids help. 22 people found this helpful. Try reversing the ignition wire.
Why does my car not start after a new battery is installed?
Another reason as to why your car might not start after having a new battery installed is due to faulty fuses and ignition switches.
How does a starter motor hook up to a negative terminal?
Re-installed the starter motor. When hooking up the new battery, I hooked up the positive side. When I touched the negative cable to the negative terminal, there were sparks, and the starter motor engaged and tried to start the engine. The keys were not in the ignition and the ignition was in the locked position.
Why is my starter not in the ignition?
When I touched the negative cable to the negative terminal, there were sparks, and the starter motor engaged and tried to start the engine. The keys were not in the ignition and the ignition was in the locked position. Verified ignition in the locked position and left keys out of ignition.
What happens when you hook up a new starter motor?
Bench tested starter motor at local auto parts shop and they said it’s fine. Battery was shot so I bought new one. Re-installed the starter motor. When hooking up the new battery, I hooked up the positive side. When I touched the negative cable to the negative terminal, there were sparks, and the starter motor engaged and tried to start the engine.
Where does the battery connect to the starter?
A small bolt goes through the strap, into the threaded hole. The other large post is where the battery cable connects. The two smaller posts. One is marked with an S and the other an I. When mounted on the starter, the one closest to the engine is where the ‘exciter’ wire connects.
How to fix stalling after replacing car battery?
Step 3: Disconnect the old vehicle battery and remove it. Step 4: Insert the new vehicle battery, use a battery brush to clean the cable ends and battery posts, connect and tighten the cables, and make sure the battery is secured in place. Step 5: Disconnect the memory saver immediately, before starting the car.
Do you need to initialize an ECU after reconnecting the battery?
In some cases, this may also occur if the battery voltage becomes low or if the battery is recharged. After the battery is reconnected, these systems must be initialized before they can work properly. An ECU also typically requires initialization after the ECU or a component it controls has been removed or replaced. Customized Settings
What are the signs of a bad starter relay?
Broken or corroded wiring – Damaged or dirty wires to the battery or to the starter solenoid (or wires that are loose) can prevent sufficient power from reaching the starter. Alternator – The alternator is designed to power all of your car’s electrical systems when the vehicle is running. It also recharges the battery.
Can a small gauge wire trigger a starter?
Smaller gauge wire should have no power without key in “start” position but if it can get power from anywhere it will trigger the starter. Look again to see if something is touching or too close there. Lag bolts aren’t used for starters normally – sometimes to fake it with exhaust parts but not likely from that area??
Re-installed the starter motor. When hooking up the new battery, I hooked up the positive side. When I touched the negative cable to the negative terminal, there were sparks, and the starter motor engaged and tried to start the engine. The keys were not in the ignition and the ignition was in the locked position.
Smaller gauge wire should have no power without key in “start” position but if it can get power from anywhere it will trigger the starter. Look again to see if something is touching or too close there. Lag bolts aren’t used for starters normally – sometimes to fake it with exhaust parts but not likely from that area??
Where is the exciter wire on a starter?
When mounted on the starter, the one closest to the engine is where the ‘exciter’ wire connects. That wire should have power to it only in the ignition start position. Nothing will be connected to the other post.
Why does my car battery click when I turn it on?
That and my original battery attached is an aftermarket Gel battery that shows a full 12.6V charge. The “click” you get, does it sound like the starter engaging but just doesn’t turn over or is it the “click click click” when you actually have a dead battery without enough juice to engage the starter?
How can I tell if my spark plugs are still working?
Of course, your engine needs to have spark to ignite the air/fuel mixture to start. The first place that you should check is the spark plugs. To test to see if they are still working, you can remove them and then plug them back into the plug caps. Next, ground the plug on a head bolt and turn the motor over.
Why are my spark plugs not working on my snowmobile?
A weak plug may be able to spark in the open, but will not under the compression of the cylinder. Fortunately, most spark plugs are inexpensive. If you still do not have spark after installing new spark plugs, then you have an issue with your electrical system.