Why does my Mazda 3 not start when I turn it off?

If the battery is relatively new, it can be recharged. One way to do this is to start your car and let the engine run for a while to recharge the battery. One thing to know: if the battery is over 4-5 years old, it may be completely dead, so it will not recharge and the car will not restart after you turn it off.

Where is the ignition switch on a Mazda 3?

An ignition switch is an electrical switch installed on the rear of the ignition lock mechanism. If shaking the key in the ignition switch helps to start the car, you should check the ignition switch first. The starter solenoid control wire may have a bad connection.

Why does my car not start if the battery is OK?

If the battery is OK, but the starter still won’t start, there could be a number of possible reasons. Here are a few: The ignition switch could be faulty – this is a common problem.

What should I do to my Mazda 2?

Handling modifications are a good place to start for the Mazda 2. Fully adjustable suspension allows you to fine tune the handling of you Mazda 2 radically improving your drive. Drop the car by as much as 24mm – 40 mm. and fit motorsport grade stiffer dampers, bigger drops will need other modifications in most instances.

What kind of car is the Mazda 2?

The Mazda 2 is a awesome car modification project to fill your spare time. The Mazda Demio was branded the Mazda2 in many markets and previously as a 121. The third generation is indistinguishable from the first generations, thanks to giant advances in design and styling.

Is the Mazda 2 a good sleeper car?

Mazda 2 make good sleepers if you debadge them and fit the most powerful engine upgrades and handling upgrades you can source! Sadly with smaller engine sizes you are wasting your time spending money on modifications, so if this applies to you get yourself an engine swap then apply the following mods.

What are the problems with the Mazda MZ6?

The system on the Mz6 had two problems initally. 1)If the owner was filling the vehicle with fuel and the test was running…PO455 large leak. 2) If the owner used the remote to lock the doors while the test was running, the door lock motors caused a drain on the battery and the time for the test never made the specified time.

Where is the change over valve on a Mazda 3?

A Small (6″x6″) module is mounted near the fuel tank of the vehicle. Each module contains a small pump and a COV (Change over valve). The COV is a three way valve. Position 1) is vented to atmosphere.

Is there a problem with the Mazda ECUs?

Fortunately, a recall announced by Mazda is a better example of the less-grave errors computers can cause. The problem isn’t small for Mazda, however, even if it’s relatively easy to fix. It all centers around the software Mazda’s ECUs use to regulate cylinder deactivation.

Are there any problems with the Mazda CX 5?

Thankfully, the fix involves nothing more than a software update to the PCM. Vehicles affected with the faulty software are the 2018 and 2019 model-year Mazda6 and CX-5 as well as the 2019 Mazda3. Track-Weapon Warfare: GMA T.50s Niki Lauda Vs.

What does a Mazda 3 engine sound like?

He (AAA guy) said the engine sounds like a sawing machine and the timing chain is gone. So I took off the oil filler cap and looked inside with a flash light so that I can see the cam closest to the firewall/driver.

What to do if your Mazda doesn’t start?

Mazda MAZDA6 Questions – Car doesn’t start. Turning key in ignition doesn’t do anything. – CarGurus Car doesn’t start. Turning key in ignition doesn’t do anything. were working. I even checked the headlights, and they worked as well. As anymore. A red light on the dashboard is the only visible light (Besides door

Why does my Mazda 6 2.5 start in neutral?

6 people found this helpful. 2013 Mazda 6 2.5, the car is starting in Neutral for me as you said @RK , should we go to fix this with the dealership and tell them about the parking cable and Transmission Neutral Switch? 1 people found this helpful.

Why is the Immobilizer flashing on my Mazda6?

Turns out it was a simple fix, they said that the Transmission Neutral Switch and parking cable needed to be reseated/adjusted. The tech explained, the reason I was having the starting issue with immobilizer flashing is because this switch was out of place and was not able to communicate to the on-board computer the proper gear the car was in.

What to do if your Mazda Tribute won’t start?

2006 mazda tribute 2.3l wounld’n crank and stall sometimes: I replaced ignition switch ( electrical part that is connected to the interlock) without doing anything else and the problem has gone for good, guys. It cost about $30.00 plus . Good luck!

When does the istop stop working on a Mazda 3?

It will stop working if you do many short trips when the battery is discharged. When you do a long trip or charge the battery so the battery is at full charge then iStop still doesn’t work for a while until it detects the battery is above a given charge level for a certain length of time.

What should battery state be for Mazda istop?

When you take it in for its first service tell them to check the battery state of charge as you’ve been told that it has to be a minimum of 75% for the istop to work. Just don’t tell them where you heard that 😉

What happens when you replace the battery in a Mazda 3?

After you replace your battery, even you replace the battery with start-stop compatible one, your i-stop most probably will not work. You need to activate/reset it again. There is a procedure to do it like pressing to i-stop button some seconds etc. And btw you have the original mazda battery.

Why are there spark plugs in my Mazda 3?

Took out the spark plugs, then rotated the crankshaft pulley and I could see the camshaft rotate, so that meant to me the timing chain is still in one piece and at least partially functional. Next put a screwdriver into spark plug hole #1 and set the crankshaft pulley to its timing mark.

What to do if your Mazda3 won’t start?

One way to do this is to start your car and let the engine run for a while to recharge the battery. One thing to know: if the battery is over 4-5 years old, it may be completely dead, so it will not recharge and the car will not restart after you turn it off. In this case, you may need a new battery.

What should the battery voltage be on a Mazda 2?

Connect voltmeter to the battery ,first you should read battery voltage ,a good fully charged battery should have 12.6 volts . now check the voltage when trying to start the battery should not drop below 10 volts if it does recharge the battery or replace .

What’s the problem with my 2010 Mazda3?

No idea if it’s the alarm/immobilizer, battery, or something else. It’s a 2010 Mazda3. I’m hoping to avoid towing it to the Mazda dealership, although at this rate, it looks like I might have to. -Car wouldn’t start; it cranked, but wouldn’t catch.

Why are the blinking lights on my Mazda3 not working?

It has enough charge to keep those blinking light and radio on but not enough for everything. The blinking lights will still work, the radio and such will still work. As you noticed once you turned on the headlight with the radio on, it turned off. Sure sign of battery issue.

What causes a car to start but not keep running?

The engine requires the right amount of air and fuel to mix together for ignition. If there is a fuel leak somewhere, then the correct amount of fuel may not make it to the combustion chamber. This might be enough to allow the engine to start, but not keep running.

What causes a car to start and then die?

But if there is a fuel leak somewhere, then the proper amount of fuel won’t be able to make it to the combustion chamber. This might cause the engine to still start, but it won’t be able to keep it running. That is why it will die almost immediately after it starts.

Is the Mazda i stop system a good idea?

Mazda’s i-Stop system is the ‘Coca-Cola’ of auto engine shutdown systems – and while they try hard to sex up the benefits, the cars would be better without it One of the most glaring examples of this carmaker agenda self-serving design is the auto engine shutdown and restart system.

Can you turn off automatic engine shutdown and restart?

Some automatic engine shutdown and restart systems can be properly turned off if you prefer – but for many, the default state on every startup is ‘active’ – unfortunately. BUT CAN YOU TURN IT OFF?

How does an auto stop start system work?

The engine automatically shuts down. The light goes green, you start lifting off the brake, and the engine kicks back into life, as if by magic. We’re talking about that. Systems like Mazda’s i-Stop – and seemingly 100 other proprietary names for similar bullshit technology.

Why is my Mazda 3 engine not starting?

There are a lot of issues that can cause your 3 to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code. It is definitely worth it to use an OBDII scanner to check and see if the engine has thrown any trouble codes.

What kind of spark does a Mazda 3 have?

I check the spark by taking out all the spark plugs, then holding one after the other against the metal block and checking for spark while someone turned the ignition. All 4 plugs showed spark, and they looked strong with a bluish spark color.

How can I tell if my Mazda 2 battery is full?

Now to check this is very easy. all you need is a voltmeter that has min 20 volts . Connect voltmeter to the battery ,first you should read battery voltage ,a good fully charged battery should have 12.6 volts . now check the voltage when trying to start the battery should not drop below 10 volts if it does recharge the battery or replace .

Why does my car not start when I start it?

When you first go to start your car and all you hear is the engine attempting to turn over, it is most likely your battery at fault. Granted, it could also be a starter, an alternator, or something else entirely, but over 90% of the time when a vehicle doesn’t start and has been overall well-maintained, the battery is at fault.

Why is my Mazda door FOB not working?

The key fob for your Mazda has a built-in chip that’s programmed so your security system will both recognize and accept it – allowing you to open your doors. You obviously use your keyless remote to open your Mazda door because it is convenient. When it stops working, the first thing you want to do is fix it.

What kind of engine does a Mazda 3i have?

I have a 2005 Mazda 3i 2.0L 5 speed manual. I bought it back in April with 92,000 miles and it now has 110,000 miles. It has a catback straight pipe exhaust and the previous owner said the engine was swapped, due to a timing chain failure on the previous one.

Why is there no check engine light on my Mazda 5?

No check engine light or other indictors of a problem. It’s as if the PCM is seeing (or not seeing) something it doesn’t like and shutting down the process. Here’s what I (and various mechanics) have done.

What does it mean when your Mazda 3 won’t start?

This just means that the engine doesn’t move when you turn the key. The second way that your 3 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own. When the engine isn’t turning over at all, that’s a bit easier to diagnose than when it is cranking but not firing.

What are the specs of a 2006 Mazda3?

A moonroof, a custom-tuned Bose audio system and Sirius Satellite Radio are optional. Comparatively upright in profile, the Mazda3 is built with a wide track and a relatively long (103.9-inch) wheelbase for its size. A Sport Package that includes sport bumpers, side skirts, 17-inch wheels and fog lamps is available on s sedans.

What kind of engine does a Mazda3 I have?

The 2.0-liter four-cylinder in the Mazda3 i develops 150 hp (145 hp in PZEV form). The Mazda3 s uses a 2.3-liter four-cylinder that pumps out 160 hp. A five-speed-manual gearbox is standard, and a four-speed-automatic transmission with a manual-shift provision is optional for the Mazda3 i.

When did the Mazda 3 go on sale?

Mazda’s larger, more powerful replacements for the departed Proteg� sedan and Proteg�5 hatchback went on sale in the 2004 model year. Built on the same platform as the Volvo S40, the compact, front-wheel-drive Mazda3 displayed entirely different styling.

Are there any problems with the Mazda3 air conditioner?

Mazda MAZDA3 owners have reported 7 problems related to air conditioner (under the equipment category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Mazda MAZDA3 based on all problems reported for the MAZDA3.

What kind of car is a Mazda 3?

A 2005 Mazda 3 Hatchback 97,000 miles. The first time, it felt like the gear had slipped out when I drove out of car lot. I parked car and turned it off and AT light disappeared when I restarted.

Why does my Mazda 3 crap out after 40K miles?

The TCMs on Mazdas 3s are pron to overheating due to their proximity to the engine and crap out after 40k miles or so. 25 people found this helpful. I must have been really lucky because mine didn’t crap out until 166k miles. But I have heard, in other forums, this happening when the car is still new (<30k miles).

What should I know about my Mazda 3?

If you can, please report the status of your Mazda3. 1. Year 2. Mileage 3. Auto/Manual Transmission 4. Transmission repaired? If yes, at what mileage? New or rebuilt? Thanks. 3. Auto 4. No. NB: When cold start, the shifting 1st to 2nd gear jerks. Is this the sign of transmission going bad? 3. Manual Transmission 5.

Why does my Mazda 3 not start in Park?

This is common problem off all mazda 3 5 and 6 they dont start in park position, only start in neutral and solution is the bracket that holds the transmission shifter cable. You just need to hammered it down towards the ground. Loading…

How many miles can a Mazda 3 get before it dies?

Hi, everyone, I am doing a survey to see how many miles can Mazda 3 get before it dies. If you can, please report the status of your Mazda3. 1. Year 2. Mileage

What to do if your car won’t start?

4. If NOTHING changed after 1.-3. and car battery still loses charge, then recharge car battery again to 100% and then open car fuse box and look which car circuit LEAKS electricity or is SHORT. Read car manual for fuse box circuit descriptions.

What kind of battery does a Mazda 6 have?

2006 MAZDA 6 Replaced key fob battery and the car battery. Nothing! 3 people found this helpful. 2012 Mazda 6 2.5, earlier I posted couple messages on this thread, one for trying to disconnect the battery – that worked for about a week but the issue re-appeared.

What’s the problem with my 2004 Mazda 3?

My 2004 Mazda 3 has been great for 40K miles. About 6 weeks ago and 2 visits to Mazda service/repair the problem has yet to be resoloved. When stopping for a red light (car in drive and brake on) a vibration with a rattle starts and stops as soon as foot lifted off brake.

What kind of engine does a Mazda 2.0 have?

I think that the 2.3 may have made more sense for the 2004-2005 models since it was the only engine with variable valve timing, which gives you more power at lower engine speeds. Mazda added VVT to the 2.0 for 2006, so that’s not an issue anymore. I just wish that the hatchback was available with the 2.0L engine.

Are there any problems with the Mazda MZR 2.3L?

To help the longevity of that L3-VE / MZR 2.3L is to replace the oil filter housing with a spin-on unit housing. Otherwise, you’ll run it empty. Use a quality filter and check your oil regularly. The L3-VE has the oil burning issue. Most cars with the oil burning problem are 2004-2005 production cars.

Why is my Mazda 3 battery not working?

If no light comes on in the dashboard and no other electrical consumer is working, the battery could be completely dead or there is no connection between the battery and the vehicle’s electrical system. Check if the battery terminals are tight.

Why does my Mazda not start when I Turn on the ignition?

If when you turn on the ignition, the “Security” light stays on or flashes, it means that your car’s security system does not recognize the key or that there is a problem with some parts of the security system itself. Sometimes the key just needs to be reprogrammed.

Why does my car not start in deep water?

If the water was deep enough to go into the breather system and get into the engine you could be looking at a hydrolock condition .

What kind of car won’t start in flood water?

Car driven in flood water, won’t start. We were idiots. Tonight driving in Melbourne, we drove through a flooded street in a 2010 Mazda 3. The engine cut out; and water was coming through the door seals. I got out and pushed the car onto high ground.

If the water was deep enough to go into the breather system and get into the engine you could be looking at a hydrolock condition .

Why does my Mazda indicator light stay on?

The PCM will trigger the indicator light to illuminate to inform you there may be an issue with your Mazda. Occasionally, the information remains stored with your PCM, even after the issue has been fixed, and your indicator light may remain on until the PCM has been reset.

When to use flexible setting on a Mazda?

Flexible setting is factory preset for some countries in Europe. Consult an Authorised Mazda Repairer for details. Flexible setting can be set if the vehicle is operated mainly where none of the following conditions apply. Purpose of vehicle use is police car, taxi or driving school car.

What happens when you reset the PCM on a Mazda?

Why does my Mazda 3 shake during acceleration?

So, my ’05 3i 200k/mi started shaking really bad (I mean really bad- so bad that I thought the car was going to literally come undone) during acceleration, right after I had the two front axles replaced. (Shady-tree mechanic work) When I brought it back, he replaced the ‘carrier’ bearing- I’ll admit I’m not exactly sure what that is.

What does the Check Engine light on a Mazda 3 mean?

When the check engine light comes on, a fault code is stored in the ECU. Diagnostic equipment is required to read the fault codes. Description: The Mazda 3 i-stop is an engine start/stop system that turns off the engine when the vehicle becomes stationary to save fuel.

Why does my Mazda keep beeping when I Turn on the light?

Turning the knob to the left will dim the light, while turning it to the right makes the light brighter. Whenever the knob has been turned to the maximum dim position, it will beep to alert you. This is what some owners have reported as being a cause for the mysterious beeping coming from their Mazda.

How to fix a Mazda that stalls at stop?

Remove the air hose from the throttle body. Disconnect the throttle body connector. Remove the throttle body from the intake manifold, with the water hose connected. Clean the throttle body on the air hose side using a soft, clean shop cloth, sprayed with engine cleaner (Mazda recommends their P/N 000-77-A86).

What kind of engine does a Mazda 3 have?

We just got my daughter a used 2004 Mazda 3 4-door sedan. It has a 2.0 liter engine. The car has about 33,000 miles on it. I decided to change the plugs and took out it’s old plugs (which were ITR6F13 – not sure which brand) and replaced them with Bosch 4211 Platinum Plugs with a gap = 0.052.

Why is my Radio not working on my Mazda 2?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: U0_PUK95xpNDZbCM)

Where are the operating instructions on a Mazda 3?

At the beginning of these repair manuals, its compilers placed the Mazda 3 operating instructions.

Why does my car make a clicking noise when I try to start it?

If you hear a clicking noise (but nothing else) when trying to start your car, that means the starter solenoid or relay contacts are operating, but the starter isn’t cranking the engine. My Car Clicks But Won’t Start—What Does it Mean?

What should I do if my car won’t start?

Begin your inspection by making sure the battery terminals are clean and tight, and that the battery cables are in good condition. Next, check the battery’s state of charge using a digital multimeter (DMM). If your battery has less than about 12 volts, you’ll want to charge it, then test it with a load tester.

Why does my car make a clicking sound when I start it?

Always Check this first! Clicking sound and the inability to start can usually be caused by low power being supplied to your car’s starter motor. Open up the car hood and check the car battery.

Why does my Mazda3’s touring have a blank screen?

Just wanted share my experience with you in case there are people having the same problem and are stuck on figuring out what to do. I purchased my Mazda3 s Touring over a month ago and ever since the infotainment system would occasionally not turn on after I started the car i.e. having a blank screen.

Why does my Mazda infotainment system not start?

Whenever we start the engine, the electricity is not at a normal voltage level because most of the power were drawn to the electric motor, I bet if Mazda can delay the start of the infotainment system for like 3 secs after we push start the engine it will fix the problem permanently.:smartass: Is Watching.

How big is the navigation screen on a Mazda?

With an 8.8-inch wide display, see destination routes clearly and easily. * Functions available depending on the region differ. For details, please contact your nearest dealer.

Why is my Mazda 3 NAV not working?

If turning the volume knob up while it’s supposed to be speaking directions, and bluetooth isn’t connected (to rule it out), it’s probably best to bring it to the dealer to have it reset. Mazda 3 2015 nav auto. UK Sat nav is working but no sounds at all.

Is the Mazda 3 Sat Nav working in the UK?

Mazda 3 2015 nav auto. UK Sat nav is working but no sounds at all. When an instruction is due the driver’s side speaker goes quiet (when radio is working) but no guidance instructions are issued. Under the settings menu, guidance volume is set high and other warning tones are enabled.

How to disable the factory alarm on a Mazda3?

If you want to steal them, just search for some posts. Others have already outlined the stock alarms weaknesses (YAY), but if you’re legitametly interested in bypassing it; The immobilizer works through your key, that’s what you want. Just disarm your stock alarm, leave it off, and install your new one and use the stock key for immobilizer duties.

What to do if your car alarm won’t turn off?

The alarm system won’t turn off (disarm itself) with the keys alone! You NEED THE REMOTE TO DO SO! Imagine… So, I change the battery in the remote (2 x CR2016) and LOCK the car, then, UNLOCK the car and hold the UNLOCK BUTTON FOR 3 SEC. The system disarmed itself and the problem was solve!!! Now, read this carefully;

What should I do if my Mazda security system is not working?

The security indicator light illuminates for about 3 seconds and then turns off. If the engine does not start with the correct key, and the security indicator light remains illuminated or flashing, try the following: Make sure the key is within the operational range for signal transmission. Switch the ignition off, and then restart the engine.

When do you push the start button on a car?

March 19, 2017. The Push Button Start is a next step from an old way of inserting the key into the ignition and turning it to stat. You get into the car, press the brake, push the button and it starts.

Why is my Push Button Start button not working?

Often, when a key fob battery becomes weak, the key fob fails to communicate with the car. The solution is to place a key fob close to the start button, like in the photo or if there is a special slot for the key fob, insert it into that slot .

What does push button start on Mazda 3 mean?

Refer to Engine Start Function When Key Battery is Dead on . CAUTION If the KEY warning light (red) illuminates, or the push button start indicator light (amber) fl ashes, this could indicate a problem with the engine starting system and the inability to start the engine or switch the ignition to ACC or ON.

How do you start a Mazda 3 without starting the engine?

To switch the ignition position without starting the engine, perform the following operations after the push button start indicator light (green) turns on. Release the clutch pedal (manual transaxle) or brake pedal (automatic transaxle). Press the push button start to switch the ignition position.

Why does my Mazda 3 not start when I shift into neutral?

If you must restart the engine while the vehicle is moving, shift into neutral (N). NOTE (Manual transaxle) The starter will not operate if the clutch pedal is not depressed sufficiently. (Automatic transaxle) The starter will not operate if the selector lever is not in P or N and the brake pedal is not depressed sufficiently.

Can a car start with a push button start?

An automatic car with a push button start can only be started when the transmission is in Park or Neutral. Sometimes a gear selector switch fails and even when you shift the transmission lever into Park, it still indicates that it’s not in Park.

What to do when your Mazda remote stops working?

When it stops working, the first thing you want to do is fix it. Before you head off to buy a new remote, there are a few other things that you can do to try and get it to work again. Simultaneously hold the open and the lock button down for 60 seconds. This should reset the system. If it worked, the interior car lights will go on and off.

Why does my Mazda 3 not start when parked?

The starter itself or a starter solenoid may be faulty. A problem with a neutral safety switch. If a car does not start with the transmission parked, but starts in neutral, it may be due to a problem with a neutral safety switch or the shift lever cable.

Can you turn on lights with a dead battery?

1. Battery appears to be ok – all lights and accessories come on, remote entry works, etc. There’s a big difference between having enough power to turn on some lights and having enough power to crank the engine. Your symptoms sound exactly like a dead battery.

What to do if your Mazda 3 battery dies?

Click to expand… You can buy one of those but most garages will do that test for free in the hopes of selling you a battery. If you have a garage buy a battery tender and hook it up right away when you bring your car home, then periodically or any time you store the car.

If the battery is OK, but the starter still won’t start, there could be a number of possible reasons. Here are a few: The ignition switch could be faulty – this is a common problem.

What to do if your car battery is dead?

Charged the car battery 3.) Only way to start the car is to hold the key fob close to the start button, put your foot on the brake pedal, then keep holding the start push button 4.) Car will then start and the start push button turns the color green. 5.)

Why does my Mazda make a beeping noise?

Although the list above could be causing beeping sounds to be heard, chances are if you’ve come this far in your search, there is another cause. And chances are, that cause is the dashboard illumination dimmer. The illumination dimmer knob can adjust the illumination level of the dashboard and instrument panel lights.

Why does my Mazda 3 make a whining noise?

If your Mazda 3 is experiencing a whining noise, its is often going to be caused by something in the engine compartment. The likely cause of whining noise will be determined by when you hear the noise, and under what conditions With that in mind, this page is divided by when you hear the whining noise, and common causes under those conditions.

What should I replace in my Mazda 3?

So far I’ve replaced the front control arms, outer tie rod ends, all 4 struts/shocks, front wheel hub/bearing assemblies, new tires (cheapo tirerack but they’re quiet), and had the transmission flushed at the Mazda dealer. A few other parts I’ve replaced before this are the 3 engine mounts- they are OEM Mazda and have about 20k on them.

How does the front end of a Mazda feel?

A few other parts I’ve replaced before this are the 3 engine mounts- they are OEM Mazda and have about 20k on them. The front end feels a bit tighter, but it still feels sluggy and shakes like crazy when accelerating.. any thoughts?

How much does a used 2010 Mazda3 cost?

How Much Does the Used 2010 MAZDA MAZDA3 Cost? The Manufacturer’s Suggested Retail Price (MSRP) schedule on the multi-tiered 2010 MAZDA3 lineup starts at just over $15,700 for an “i” SV sedan, which makes it a relative bargain among its primary competitors.

Which is the best review of a Mazda 3?

Edmunds’ expert review of the Used 2010 Mazda 3 provides the latest look at trim-level features and specs, performance, safety, and comfort. At Edmunds we drive every car we review, performing road tests and competitor comparisons to help you find your perfect car. Read the full in-depth review of the Used 2010 3 at Edmunds. Popular searches

How big is the DOHC in a Mazda 3?

Mazda had a well build 2.3 liter 4 cylinder 16 valve dohc that was being used in thier Mazda 3 successfuly for years . in 2010 Mazda had already began work and massive investment into thier skyactive systems which eventually were launched in 2013 .

How many engines does a Mazda3 have?

Two engines and three transmissions are part of the revitalized MAZDA3 lineup for 2010.

Navigation