Why does my Honda SRS light keep blinking?
The SRS light will blink twice indicating the SRS system and the light are reset. If this procedure is followed correctly and the light remains on, then there may be an actual issue with the SRS system. In this case, it is advised to bring the vehicle to the dealership, where the trouble code can be identified and the issue repaired.
How can I tell if my SRS light is on?
The scanner flashes slowly to indicate the first part of the numerical error code and then uses a second quick flash for the second number of the code. I recommend that you check the code and go from there. I’m guessing that it will show a “non-functional” code; this is a common problem.
Where is the reset button on a Honda SRS light?
To do so, you will be “shorting” the system in order to reset the light. Locate the MES (Memory Erase Signal) connector. It is below the dashboard on the driver’s side of the car plugged into a panel (there is no electrical connection). Figure 1. MES location under the dash.
What does SRS stand for in Honda Civic?
Learn how to do so here. This article applies to the Honda Accord (1990-2002) and Honda Civic/Del Sol (1992-2000). The secondary restraint system, or SRS, is a safety system in your Honda that controls the airbags, among other things.
How do you reset the SRS light on a Honda Civic?
Disconnect the paper clip as soon as the light goes off. When light comes back on reconnect the paperclip. Wait for the light to go off once more then disconnect the paperclip. The SRS light will blink twice to indicate that its memory has been erased. Turn off the ignition and wait ten seconds to restart the car.
Why is my SRS light not working on my Honda Accord?
Tried the battery thing, the MES plug light reset and basically nothing works, Most cheap scanners including the Snapon Solus-Pro won’t read air bag .or abs codes.
What does long Blink on SRS light mean?
Any code with 5, 6, 7, 8, or 10 long blinks means that the problem is with the SRS module. If the code is a 1 or 2 then the problem is with the driver’s or passenger’s air bags respectively. If the code is a 9 then the problem is with the power supply. Figure 3. Service check connector under the glovebox.
What happens when you reset the SRS light?
The SRS light will blink twice to indicate that its memory has been erased. Turn off the ignition and wait ten seconds to restart the car. The light should come on for a moment then go out. Figure 2. SRS light (highlighted above) will blink twice when it’s been reset.
How do you turn off the SRS light on a Honda CRV?
Strip the ends of both wires using a knife. Keep the ends of the wire touching while you do this. Repeat Step 3 and the SRS light will blink twice and turn off. Unshort the two wires. This will cause the SRS light to blink twice.
What should I do if my SRS light keeps coming on?
If you don’t have wires, you can use paperclips instead. Hold the ends of both wires together, and turn on the ignition. The SRS light will come on, and after a few seconds it will turn off. Once the light turns off, pull the wires apart. The light should turn back on. Hold the stripped ends of both wires together again.
What does the SRS light mean on a Honda Accord?
The SRS light is a warning light for your supplemental restraint system (airbags). An SRS light means that there is a problem in the system. The first thing I would check is the fuse for the SRS unit. The only way to check this is with a scan tool of some sort. I used a Solus Pro.
The SRS light will blink twice indicating the SRS system and the light are reset. If this procedure is followed correctly and the light remains on, then there may be an actual issue with the SRS system. In this case, it is advised to bring the vehicle to the dealership, where the trouble code can be identified and the issue repaired.
To do so, you will be “shorting” the system in order to reset the light. Locate the MES (Memory Erase Signal) connector. It is below the dashboard on the driver’s side of the car plugged into a panel (there is no electrical connection). Figure 1. MES location under the dash.
If you don’t have wires, you can use paperclips instead. Hold the ends of both wires together, and turn on the ignition. The SRS light will come on, and after a few seconds it will turn off. Once the light turns off, pull the wires apart. The light should turn back on. Hold the stripped ends of both wires together again.
How can I tell if my SRS is working?
Unless checked and repaired, the SRS will not function reliably. A malfunction is shown by: The indicator light flashing or flickering. The SRS indicator light failing to illuminate when the ignition switch is first turned to the II position. The SRS indicator light continuously illuminated. The SRS indicator light illuminated while driving.