Why are the axle seals leaking on my Honda Civic?
Most axle seals leak because they were not properly seated during installation. Fortunately, the repair is relatively simple. This article applies to the Honda Civic (1990-2000).
What does it mean when your axle seals are leaking?
Leaking oil from the passenger’s or driver’s side of the car indicates a problem. It could be a leaking axle seal. Most axle seals leak because they were not properly seated during installation. Fortunately, the repair is relatively simple.
Why is oil leaking from the front of my Honda?
It is possible that is did slide completely out of the hole. You will have to add a retainer that holds this seal in place. It will be with a timing belt package which is available at your nearest automotive store. You have that seal as well as three others, that could be leaking beneath the timing our timing belt cover.
How do you remove axle from Honda Civic?
Tie rod end disassembled. With all of the accessory hub items removed, remove the axle from the transmission. To do this, unbolt the hub from the axle by removing the cotter pin, and using an axle nut tool to remove the axle nut. This will free the axle from the hub side. From here, you have access to the inside of the axle.
Most axle seals leak because they were not properly seated during installation. Fortunately, the repair is relatively simple. This article applies to the Honda Civic (1990-2000).
Leaking oil from the passenger’s or driver’s side of the car indicates a problem. It could be a leaking axle seal. Most axle seals leak because they were not properly seated during installation. Fortunately, the repair is relatively simple.
Tie rod end disassembled. With all of the accessory hub items removed, remove the axle from the transmission. To do this, unbolt the hub from the axle by removing the cotter pin, and using an axle nut tool to remove the axle nut. This will free the axle from the hub side. From here, you have access to the inside of the axle.
How do you remove seal from Honda Civic?
Pull the axle away from the transmission housing to access the worn seal. With the seal puller, gently pry the seal up and away from the transmission housing, removing it completely from the housing. Avoid scratching or gouging the transmission housing with the tool. Figure 5. Seal puller. Figure 6. Using the seal puller to remove the old seal.
What’s the best way to install a seal?
Using the large socket in place of the seal installer to press in seal. Figure 8. Seal seated properly. Figure 9. Another view of the seal seated properly. If you don’t have a seal installer, you can use a large socket with an extension to push the seal gently into the housing.
Where is the transmission seal on a Honda Civic?
Also known as the output shaft seal, this component is the most common source of the leak. The axle shaft seal is located between the axle and transmission. Here are the steps to diagnose: Raise the vehicle, and set it down on jack stands. Shine a flashlight through the chassis to where the axle shaft meets the transmission.
What to do if your Honda Civic transmission is leaking?
Shine a flashlight on the font axles. Focus on each boot, and look for any tears or leaks. Wipe a rag over the boot, and squeeze to check if any grease leaks out. If a leak is found, the axle assembly will need to be replaced. The best option (if you see a leak) is to replace the entire axle.
Can a CV boot be replaced on a Honda Civic?
If the axle is not clicking or showing signs of excessive wear, a new CV boot can be repacked with grease and installed on the shaft. However, with replacing the boots alone, you risk damaging the axle or letting unchecked damage go.
Also known as the output shaft seal, this component is the most common source of the leak. The axle shaft seal is located between the axle and transmission. Here are the steps to diagnose: Raise the vehicle, and set it down on jack stands. Shine a flashlight through the chassis to where the axle shaft meets the transmission.
Shine a flashlight on the font axles. Focus on each boot, and look for any tears or leaks. Wipe a rag over the boot, and squeeze to check if any grease leaks out. If a leak is found, the axle assembly will need to be replaced. The best option (if you see a leak) is to replace the entire axle.
What to do if your Honda Civic boot is leaking?
When the boot tears, the grease will leak out and eventually cause the joints to fail. To diagnose: Shine a flashlight on the font axles. Focus on each boot, and look for any tears or leaks. Wipe a rag over the boot, and squeeze to check if any grease leaks out.