Where is the oil drain plug on a Harley Davidson?
The oil drain plug (or bolt, rather) is located under you bike in the center, in line with these rear foot pegs. Use a 5/8″ deep well socket to remove the oil drain plug. Make sure that you have your drain pan in place before you remove the plug. This part is where the bike should be level to get as much of the old oil out as possible. Figure 3.
How to change transmission fluid in a Harley Davidson Softail?
Use a 7/32″ Allen key or socket to start threading the plug, then switch to the 5/8″ socket. Final torque is 20 ft.-lbs. Figure 6. A small amount of metal shavings on the drain plug magnet is normal. Inspect the fill plug o-ring for damage and replace if necessary.
Why does the oil drain out of my Softail?
Many softail owners have over filled because the checked with the dipstick and the oil level didn’t register because it had drained into the sump. So, they add to “full” level, fire up the bike and have oil puking out the breathers and air filter housing.
How much oil should I put in my drain plug?
Torque the drain plug to 14 to 20 pounds, according to the manufacturer’s guidelines. The age-old question is what kind of oil you should use. Harley recommends their specific oil of course, but any motorcycle-rated oil will work just fine and you can choose between synthetic or regular Dino.
What kind of drain plug does a Harley Davidson use?
Adapters are available for some models. (The EZ-102 will fit drain plug size 5/8″-18 UNF) (On some models 2014 & on, use A-102 adapter due to recessed oil pan) EZ Oil Drain Valve : Replaces the standard oil drain plug, making oil changes easier, saving valuable time and expenses.
Where to drain oil on a Harley Davidson Twin Cam?
Drain the transmission oil. The transmission drain plug it centered directly above the shock absorbers. Because both the engine and transmission drain plugs are so close to each other, they can easily be drained simultaneously into the same drain pan.
How to do an oil change on a Harley Davidson Softail?
Follow along as Bob teaches you how to drain the fluids on your Harley Softail, including the primary, engine oil and the transmission drain plugs. You’ll also learn how to expertly reinstall the oil filter, and which parts must be replaced each time you perform a Harley Davidson oil change and service your motorcycle.
How does an EZ oil drain valve work?
EZ Oil Drain Valve : Replaces the standard oil drain plug, making oil changes easier, saving valuable time and expenses. Lift the lever of this nickel plated brass ball valve and give it a quarter turn to open it “with your finger”. Return the lever to its original position and it locks closed.
On page 102, there is a photograph of the oil pan. It shows the oil drain plug as being on the bottom of the pan and transmission drain plug as being on the side. Which one is the oil drain plug?? I called a Harley Davidson factory warranty representative at HD headquarters. He looked it up on the computer and talked to a factory tech.
Where is the oil drain plug on a mower?
It shows the transmission drain plug as being on the bottom of the pan (facing the ground) and the oil drain plug as being on the side of the pan (facing 9 o’clock when viewing the bike from the rear). The problem is, the owner’s manual shows exactly the opposite. On page 102, there is a photograph of the oil pan.
Where is the drain plug on a V-twin?
The correct drain plug is easy to find. Get down under your bike on the drive belt side. Look up underneath the primary cover. You’ll see a 5/8ths hex head bolt that’s mounted sideways into the oil pan. If you look a little further under and forward, you’ll see the transmission drain bolt that faces the ground.
Do you need drain plug to change oil?
If you’re going to change your own oil, you’ll need a short 5/8th socket to pull your drain plug. You will also need a strap type oil filter wrench, a 1/2 in and 3/16 in open wrenchs to remove the shift linkage (at the shifter) so you can get the old oil filter out.
Where is the oil drain plug on a V-twin?
Get down under your bike on the drive belt side. Look up underneath the primary cover. You’ll see a 5/8ths hex head bolt that’s mounted sideways into the oil pan. If you look a little further under and forward, you’ll see the transmission drain bolt that faces the ground.
How do you drain oil from HD 103?
You will start by loosening your fill plug and letting it rest in the case opening. This allows for venting while blocking the opening from any potential debris that may fall into the case. Remove your drain plug and let the oil drain completely. While the HD 103 oil is draining, move on to your oil filter.
It shows the transmission drain plug as being on the bottom of the pan (facing the ground) and the oil drain plug as being on the side of the pan (facing 9 o’clock when viewing the bike from the rear). The problem is, the owner’s manual shows exactly the opposite. On page 102, there is a photograph of the oil pan.
If you’re going to change your own oil, you’ll need a short 5/8th socket to pull your drain plug. You will also need a strap type oil filter wrench, a 1/2 in and 3/16 in open wrenchs to remove the shift linkage (at the shifter) so you can get the old oil filter out.
Where is the oil filter on a Harley Davidson Softail?
Theoretically, the filter should be removable by hand only, but that is a rarity at best. The filter is located in front of the front V-Twin cylinder at the bottom. Turn the filter counterclockwise until it comes straight out.
Where is the oil drain plug on a softail motorcycle?
Unscrew the engine oil drain plug with a 5/8-inch socket and a socket wrench. On Softail models the engine oil drain plug is under the right side of the motorcycle’s frame, near the rear wheel. Dyna and Touring models have their oil drain plugs under the transmission housing. Drain the engine oil into an oil pan.
Where is the drain plug on a Harley Davidson Dyna?
Dyna and Touring models have their oil drain plugs under the transmission housing. Drain the engine oil into an oil pan. Replace the drain plug’s O-ring, then screw it into place after the oil has drained. Tighten the drain plug to 18 foot-pounds with a torque wrench.
How much does a Harley Davidson oil drain plug cost?
Fits both oil and tranny and primary chain plugs on my 2016 tri glide. The motorcycle shops sell these for 99 cents , each. At 3 per fluid change I’ll be in ” the home” before I use them all. Was skeptical at first but the quality is there.
When to replace oil drain plug # 11105?
Replace the #11105 o-rings each oil change to prevent leaks and keep your equipment running and in top shape. Molded from OEM spec material to match the performance you expect. Captain O-Ring’s orange o-rings are molded through with orange rubber material, not just a surface coating. Your engine configuration may vary from the photo above.
What do I need to change oil on a Harley Davidson Softail?
Materials Needed Replacement oil (either Dino or synthetic will do) Catch pan Replacement oil filter Shop rags Oil filter wrench (optional) Torque wrench Motorcycle lift or 2×4 block of wood (optional)
How do you drain oil out of a Harley Davidson?
1. Remove oil filler cap again and visually check for oil in the tank. 2. “If oil is not visible in the tank”, install the filler cap. If the oil pressure lamp stays lit after starting engine, immediately shut the engine off. 5. Start and idle the engine for 30 seconds. Stop the engine.
Materials Needed Replacement oil (either Dino or synthetic will do) Catch pan Replacement oil filter Shop rags Oil filter wrench (optional) Torque wrench Motorcycle lift or 2×4 block of wood (optional)
Look directly below the seat– and slightly behind it – underneath the frame to find the oil drain plug. Use a ratchet and 5/8-inch socket to remove the drain plug. Once loose, finish removing the plug by hand to avoid dropping it into the oil pan.
What size is Harley drain plug?
M18x1. 5×12 Magnetic Drain Plug for Harley Davidson Harley Davidson’s Porsche-designed V Rod engines require only one drain plug – for the engine oil, transmission oil, and for the primary chain case. This drain plug works for all three and is equipped with a 1/2″ diameter high-temperature magnet.
Where do you drain oil on a Harley Davidson?
Drain the transmission oil. The transmission drain plug it centered directly above the shock absorbers. Because both the engine and transmission drain plugs are so close to each other, they can easily be drained simultaneously into the same drain pan. Stand your Harley upright.
When to remove oil plugs on Harley Davidson?
It is of utmost importance to remove the engine oil and transmission oil fill plugs along with the primary derby cover; either before draining the oils or before the drain plugs are reinstalled. This will help to avoid confusion as to whether or not the oil has been replenished before attempting to start the motorcycle.
What causes an oil pan to be damaged on a Harley?
The most common way oil cases become damaged is from Harley drain plug over tightening. If the engine oil or transmission oil drain plug allocation becomes stripped on a touring model, the entire oil pan may need to be replaced.