Where is the OBD plug on a Jeep Wrangler JK?
OBD connector location for Jeep Wrangler JK (2007 – 2018) You will find below several pictures which will help you find your OBD connector in your car. The OBD II port is located above the pedals on the left. Go to the OBD2. scanner for JEEP. The OBD 2 plug is visible on the left of the pedals.
Where is my OBD2 port in my car?
The norm states that the port must be located inside the vehicle passenger compartment. Depending on the make and model, it may or may not be easy to locate. To diagnose your vehicle yourself, download our EOBD-Facile car diagnostic software. Use our search engine below to locate your OBD2 port!
How many pins does an OBD connector need?
In order to save you time, we have made available (for free) the information uploaded by our community of tens of thousands of users. Since the implementation of the OBD standard, each vehicle has a standard 16-pin connector, as described on our OBD presentation page.
Where is the OBD connector on a Jeep Wrangler?
OBD connector location for Jeep Wrangler TJ (1995 – 2006) RHD You will find below several pictures which will help you find your OBD connector in your car. The OBD II port is located above the pedals on the right Go to the OBD2
The norm states that the port must be located inside the vehicle passenger compartment. Depending on the make and model, it may or may not be easy to locate. To diagnose your vehicle yourself, download our EOBD-Facile car diagnostic software. Use our search engine below to locate your OBD2 port!
In order to save you time, we have made available (for free) the information uploaded by our community of tens of thousands of users. Since the implementation of the OBD standard, each vehicle has a standard 16-pin connector, as described on our OBD presentation page.
When to change spark plugs on 2013 Jeep Wrangler?
I changed the plugs this past summer on my 2013 JKU at 80,000 miles. I was about to take a road trip from Louisiana to Colorado and back so I was hoping to get the best engine performance that I could with such a long drive.
What’s the maintenance interval on a Jeep Wrangler?
The 3.6 pentastar is a lot different from my LA318 from ’69. The computer will tell you if the coil packs or spark plugs are not functioning within specs. So 100k is the maintenance interval. I never thought about changing the plugs in my 09 but when I did at 102K, I also had the cables replaced as well (3.8, no coil packs over the plugs).
How to test IAT sensor on Jeep Wrangler YJs?
To test you need a multi-meter and a hot hair dryer. Make sure that the engine is cool to ensure accurate testing. Unplug the sensor from the engine harness. Remove it from the engine. Test the sensor leads with your ohm meter while the sensor is still cool, note the current temperature.
Where is the IAT sensor located on a Jeep Cherokee?
IAT Sensor. IAT sensor (Intake Air Temperature) basically monitors the temperature of the air coming into the engine. The PCM uses this temp information to adjust the air/fuel based on the air temperature/density. Where are TPS Sensors located? On Jeeps the sensor is located in the intake manifold toward the back behind the throttle body.
How to find a Jeep Wrangler engine control module?
Enter your VIN for the most accurate results. Enter your VIN for the most accurate results. We offer a full selection of genuine Jeep Wrangler Engine Control Modules, engineered specifically to restore factory performance.
Where are the TPS sensors located on a Jeep Wrangler?
IAT sensor (Intake Air Temperature) basically monitors the temperature of the air coming into the engine. The PCM uses this temp information to adjust the air/fuel based on the air temperature/density. Where are TPS Sensors located? On Jeeps the sensor is located in the intake manifold toward the back behind the throttle body.