Where does the ground go in a Honda blower motor?
The blower motor control module (Honda calls it Power Transistor) supplies the ground. The power transistor has 4 wires: two come from the climate control system control unit, one is the ground, one goes to the negative terminal of the blower motor.
How does the blower motor work on a Honda Accord?
Typically it can be activated by pressing and holding different buttons. Testing Honda power transistor (blower motor control module). For example, in the 2009 Honda Accord, the service manual describes the procedure as follows: Turn the ignition to ON.
How is the speed of the blower motor controlled?
The electronic module that controls the speed of the blower motor is called a blower motor control module. In some cars, the blower motor has only 4 or 5 fixed speeds. In this case, the speed of the blower motor is controlled by a blower motor resistor.
Where is the blower control switch on the dashboard?
The blower control switch on the dashboard controls the circuit flow of the blower motor to adjust the voltage from low, to medium, to medium-high, to high. When on high, the circuit bypasses the blower resistor.
The blower motor control module (Honda calls it Power Transistor) supplies the ground. The power transistor has 4 wires: two come from the climate control system control unit, one is the ground, one goes to the negative terminal of the blower motor.
Typically it can be activated by pressing and holding different buttons. Testing Honda power transistor (blower motor control module). For example, in the 2009 Honda Accord, the service manual describes the procedure as follows: Turn the ignition to ON.
How does the HVAC control head work on a blower?
In those applications, the HVAC control head is a digitally controlled unit and uses various sensor inputs to determine when to supply heat. Based on the driver’s input to the blower speed switch, the HVAC control head sends a digital signal to the blower motor speed control module.
What causes a blower motor to stop working?
In a situation where the motor doesn’t work on any speed, the most likely causes are: a blown power supply fuse, a bad motor ground connection, bad motor speed control module or a failed motor. On all systems, a failed blower motor is least likely. Blower motors generally don’t fail out of the clear blue.
Why is my Honda Odyssey not blowing cold air?
Air is blowing through the front vents. I still sense that the air does not get cold like it use to. When the car is idle the air is not as cold as it use to be. It only gets very cold when we are on the road. I also sense that putting on the rear ac seems to help the front get colder.
What does it mean when AC blows hot air on one side?
AC Blows Hot or Cold Air on One Side with Clicking Sound. If you experience the symptom of the AC blowing hot or cold air on one side but not the other and it’s accompanied by a clicking or ticking sound, it probably means a gear in the temperature blend door actuator is faulty and the actuator needs to be replaced.
How can I tell if my blower motor has a problem?
Press and hold the OFF button and within 10 seconds press and release the Window Defogger button five times. The system enters the self-diagnostic mode and at the end of it, if there is a problem, the fault code will be displayed on the display.
Where is the blower motor resistor on a Mazda 5?
In many cars it’s fairly easy; the blower motor is located behind the glove box and held by 3-4 screws. In others it might be located inside the dash (e;g Mazda 5) which makes replacement difficult. If you need a proper diagnostic procedure, we posted several links where you can access a service manual for your car for a subscription fee.
How can I tell if my blower motor resistor is bad?
Attach the clip lead of the test light to a good ground like a bolt screwed into metal, and touch the sharp probe end to the terminals on the fuse. An indication of power at both terminals of the fuse determines that the fuse is good. If one of the terminals has power and the other does not, the fuse is bad. Replace the fuse as needed.
How to test Honda Accord blower motor resistor?
Testing Honda power transistor (blower motor control module). For example, in the 2009 Honda Accord, the service manual describes the procedure as follows: Turn the ignition to ON. Press and hold the OFF button and within 10 seconds press and release the Window Defogger button five times.
How does a blower motor resistor work in a car?
This is done, so the resistor or a control module is cooled down by passing air. In some older cars, a blower motor resistor was installed on the firewall with the access from under the hood. Problems with a blower motor resistor are common in many cars.
Where is the blower motor resistor located on a car?
It’s located inside the dash, often on the opposite side of the steering wheel or inside the engine compartment on the firewall. A blower motor resistor or a blower motor control module is the part that controls the speed of the blower motor.
Testing Honda power transistor (blower motor control module). For example, in the 2009 Honda Accord, the service manual describes the procedure as follows: Turn the ignition to ON. Press and hold the OFF button and within 10 seconds press and release the Window Defogger button five times.
How does a blower motor work in a car?
Carmakers use these three common wiring methods to supply power and ground to the blower motor in a manual system using a blower motor resistor. In one design, the car maker supplies battery power to the speed switch, which switches the power to the appropriate connection on the blower motor resistor.
What are the symptoms of a failed blower motor resistor?
Blower motor resistor problems. Problems with a blower motor resistor are common in many cars. The most common symptom of a failed blower motor resistor is when the heater fan only runs at high speed and doesn’t work at low speeds.
In many cars it’s fairly easy; the blower motor is located behind the glove box and held by 3-4 screws. In others it might be located inside the dash (e;g Mazda 5) which makes replacement difficult. If you need a proper diagnostic procedure, we posted several links where you can access a service manual for your car for a subscription fee.
The electronic module that controls the speed of the blower motor is called a blower motor control module. In some cars, the blower motor has only 4 or 5 fixed speeds. In this case, the speed of the blower motor is controlled by a blower motor resistor.
What are the symptoms of a worn out blower motor?
One of the symptoms of a worn out blower motor is that it can intermittently produce a loud screeching noise when running. How to test a blower motor? If the blower motor doesn’t work at all, the blower motor itself must be tested first. Typically it’s done by measuring the voltage at the blower motor connector when it’s turned on.
Where is the blower ground on a Chevy Colorado?
Pull the door sill panel, pull the kick panel cover, and it is right there. Test the voltage of the brown wire at both sides with the motor switch on 4 and see if you have 12v on both sides. The wire is the same color brown and gauge as the wire in the motor plug. Hit me up if you have any questions! Click to expand…
One of the symptoms of a worn out blower motor is that it can intermittently produce a loud screeching noise when running. How to test a blower motor? If the blower motor doesn’t work at all, the blower motor itself must be tested first. Typically it’s done by measuring the voltage at the blower motor connector when it’s turned on.
Pull the door sill panel, pull the kick panel cover, and it is right there. Test the voltage of the brown wire at both sides with the motor switch on 4 and see if you have 12v on both sides. The wire is the same color brown and gauge as the wire in the motor plug. Hit me up if you have any questions! Click to expand…