Where are the 3 wire connectors on a GM PassLock?
2: Find the 3 wire ribbon cable, coming from the ignition switch, containing White, Black, Yellow (Sometimes White, Black, Black). These are THIN wires. 3: Locate the Black 6 position connector on the LEFT side of the steering column, right above the ignition switch position.
How do you wire a GM ignition switch?
7: Using the ohmmeter, measure from the Yellow wire (the end coming from the ignition switch), to the exposed Black wire and record the value. Measure more than once to assure you have the right value. 8: Acquire the same size resistor and 3 relays, and perform the connections shown in the diagram below.
Are there ground wires in a starter harness?
There are no ground wires in the harness that goes to the starter so if you somehow mistook a ground wire in the vicinity. helpful? I took starter off to clean connections and forgot where all wires went.
What is a wiring diagram for a Pontiac Grand Am?
Pontiac Grand Am Car Audio Wiring Diagram Whether your an expert Pontiac Grand Am mobile electronics installer, Pontiac Grand Am fanatic, or a novice Pontiac Grand Am enthusiast with a Pontiac Grand Am, a car stereo wiring diagram can save yourself a lot of time.
What do you need to know about the wiring on a Pontiac?
These Pontiac Wiring information / Aftermarket Autostart/Alarm Technical Wiring Diagrams are very useful, if not required, for the installation of alarms, autostart / alarms, remote starts, doorlock info and any other aftermarket installation that would require you to know the / Wire Information / Wiring Information of your Pontiac
What is the AMP wiring for a Pontiac G6?
Photo 1 Or Pontiac G6 Monsoon Amp Wiring – wiringall.com Cool Wiring Diagram For Pontiac G6 Gallery The Best Electrical Picturesque Monsoon Amp On All. Aug 17, ยท I would be interested in the wiring color and pinouts for the 09 Vibe with the Monsoon System.
Are there speaker wires on a Pontiac Trans Am?
Im about to work on my cousins pontiac trans am Has anyone had any luck tapping into the monsoon set up with Hi level (speaker wires to the amps. Seems to be one of the better diagrams out.
What’s the best way to wire a PassLock?
Orange/Black (or Black) and Yellow. 2: Cut the Yellow wire, and strip back some of the insulation from the Orange/Black (Or Black) wires. 3: Turn the ignition to the “Run” position ( don’t crank the starter). Measure and record the value measured from the KEY SIDE of the Yellow wire, to the Black/Orange wire.
What should I do if my PassLock light is flashing?
Connect the battery cable back to the battery. You are ready to perform the relearn procedure. Insert the Key into the ignition switch and try to start the car. It should start, and then stall, with the “SECURITY” light flashing.
How to bypass the PassLock on a GM car?
Passlock-I bypass procedure…. 1: Remove the top and bottom shrouds from the steering column. 2: Find the 3 wire ribbon cable, coming from the ignition switch, containing White, Black, Yellow (Sometimes White, Black, Black). These are THIN wires.
2: Find the 3 wire ribbon cable, coming from the ignition switch, containing White, Black, Yellow (Sometimes White, Black, Black). These are THIN wires. 3: Locate the Black 6 position connector on the LEFT side of the steering column, right above the ignition switch position.
Connect the battery cable back to the battery. You are ready to perform the relearn procedure. Insert the Key into the ignition switch and try to start the car. It should start, and then stall, with the “SECURITY” light flashing.
How often does a GM PassLock light flash?
You need a scan tool. If the signal is not correct, the PCM disables the injector and the starter and flashes the light once per second. If an illegitimate key is used or a system problem exists, the light flashes twice per second. This system allows starter operation, then kills the injectors 1-2 seconds after startup.
Orange/Black (or Black) and Yellow. 2: Cut the Yellow wire, and strip back some of the insulation from the Orange/Black (Or Black) wires. 3: Turn the ignition to the “Run” position ( don’t crank the starter). Measure and record the value measured from the KEY SIDE of the Yellow wire, to the Black/Orange wire.