When did Jeep start making the Comanche SUV?
This structure was pioneered by AMC for the 1971 “Cowboy” compact pickup prototype. From 1986 to 1987, the Jeep Comanche grille had ten slots in a similar configuration to the 1984-1987 Cherokee XJ, while from 1988 to 1992, this configuration changed to eight slots to match with the SUV.
What kind of suspension did the Jeep Comanche use?
The Comanche used the XJ Cherokee’s “Quadralink” front suspension, with coil springs and upper/lower control arms on a solid axle. It was argued that the coil springs allowed for greater ride comfort and axle articulation during off-road excursions.
What’s the cargo capacity of a Jeep Comanche?
The package included heavier-duty leaf springs and wheels, larger tires, and upgraded the rear axle to a Dana 44, which increased the stock payload ( cargo) capacity from 1,400 to 2,205 pounds (635 to 1,000 kg), well above that of any other mid-size truck. The Metric Ton Comanche’s payload rating was higher than that of many full-size pickups.
What was the low gear ratio of a Jeep Comanche?
In 1986 Command-Trac transfer cases were model NP207 and Selec-Trac were NP228, both with a 2.61:1 low gear ratios. In 1987 the NP207 was replaced with the NP231 and NP228 was replaced with the NP242, both with 2.72:1 low gears.
When did the Jeep Comanche pickup truck come out?
Jeep Comanche. The Jeep Comanche (designated MJ) is a pickup truck version of the Cherokee compact SUV that was produced from 1986 to 1992.
The Comanche used the XJ Cherokee’s “Quadralink” front suspension, with coil springs and upper/lower control arms on a solid axle. It was argued that the coil springs allowed for greater ride comfort and axle articulation during off-road excursions.
What kind of grille does a Jeep Comanche have?
Up front, the Comanche was dominated by the classic Jeep’s signature grille and a set of square headlights which enhance the robust look of the truck. From 1985 to 1987, the grille had ten slots, but since 1988 the configuration changed to eight slots.
The package included heavier-duty leaf springs and wheels, larger tires, and upgraded the rear axle to a Dana 44, which increased the stock payload ( cargo) capacity from 1,400 to 2,205 pounds (635 to 1,000 kg), well above that of any other mid-size truck. The Metric Ton Comanche’s payload rating was higher than that of many full-size pickups.
What kind of Springs does a Jeep Comanche use?
For the rear suspension, the truck used leaf springs that are considerably longer than the Cherokee’s, which give Comanches good load-carrying capacity without creating a hard ride.
How old is the 1988 Jeep Comanche pick up?
1988 2WD Jeep Comanche Eliminator Pick-up. A 24 year old gem for the Jeep enthusiast. Daily driver. NO rot anywhere, EVER. Flo… more More on Oodle Classifieds Oodle Classifieds is a great place to find used cars, used motorcycles, used RVs, used boats, apartments for rent, homes for sale, job listings, and local businesses.
What kind of frame did a Jeep Comanche have?
Unlike other pickups of the time that used C-channel frames, the Comanche’s frame design (called a “Uniframe” by Jeep) under the cargo bed was fully boxed, with a large X structure centered over the rear axle.
What kind of transmission does a Jeep Comanche have?
1988 Jeep Comanche truck 2wd, a/c, 4 speed manual transmission, Has dents and rust. Frame is in great condition and Interior is okay. Engine jumped timing and I never drove the truck I bought it AS IS. 1989 Jeep Comanche This was my daily driver until I needed a heavier duty vehicle for towing. I had intended to convert it over to 4wd.
When was the Jeep Comanche bought by Chrysler?
After the Chrysler buyout of American Motors for $1.5 billion on March 9, 1987, designed to capture “the highly profitable Jeep vehicles and 1,400 additional dealers”, the Jeep Comanche, like the similar Cherokee, received only minor changes.
This structure was pioneered by AMC for the 1971 ” Cowboy ” compact pickup prototype. From 1986 to 1987, the Jeep Comanche grille had ten slots in a similar configuration to the 1984-1987 Cherokee XJ, while from 1988 to 1992, this configuration changed to eight slots to match with the SUV.
What was the horsepower of the 1987 Comanche?
The original 1987 model was rated at 173 horsepower at 4,750 RPM and 220 foot-pounds of torque at 2,000 RPM. The horsepower rating for this version was raised to 177 horsepower at 4,750 RPM and 224 foot-pounds of torque at 2,400 RPM for model years 1988 through 1990.
How big is a full size Jeep Comanche?
The Jeep Comanche (designated MJ) is a pickup truck variant of the Cherokee compact SUV (1984–2001) manufactured and marketed by Jeep for model years 1986-1992 in rear wheel (RWD) and four-wheel drive (4WD) models as well as two cargo bed lengths: six-foot (1.83 metres) and seven-foot (2.13 metres).
What kind of engine does a Comanche MJ have?
2.1L 4 cylinder Turbo Diesel – 85 hp, 132 ft lb torque. The transfer cases used are all chain driven with aluminum housings. NP stands for “New Process” which is the brand, if you will. Front Driveshaft – On 86-87 MJs (NP207 t-case) the front shaft is a “GKN” style shaft.
When did the Jeep Comanche Olympic edition come out?
The Olympic Edition is also a rare bird. Based on the Pioneer trim, this limited-edition model was sold during the 1988 model year to commemorate the 1988 Summer Olympics and Team U.S.A. Finally, there’s the Eliminator, a sporty trim offered from 1988 to 1992.
How big is a Jeep Comanche pickup truck?
Jump to navigation Jump to search. The Jeep Comanche (designated MJ) is a pickup truck variant of the Cherokee compact SUV (1984–2001) manufactured and marketed by Jeep for model years 1986-1992 in rear wheel (RWD) and four-wheel drive (4WD) models as well as two cargo bed lengths: six-foot (1.83 metres) and seven-foot (2.13 metres).
The original 1987 model was rated at 173 horsepower at 4,750 RPM and 220 foot-pounds of torque at 2,000 RPM. The horsepower rating for this version was raised to 177 horsepower at 4,750 RPM and 224 foot-pounds of torque at 2,400 RPM for model years 1988 through 1990.