What to do when cylinder head is removed from Mazda 6?
The cylinder head and the camshaft caps are numbered to make sure they are reassembled in their original position. When removed, keep the caps with the cylinder head they were removed from. Do not mix the caps. Loosen the camshaft cap bolts in several passes in the order shown. Loosen the cylinder head bolts in several passes in the order shown.
How to install a cylinder gasket on a Mazda 6?
1. Set the cam position of the No.1 cylinder at the top dead center (TDC) and install the camshaft. 2. Temporarily tighten the camshaft bearing caps in two or three even movements. 3. Tighten the camshaft cap bolts in the order shown using the following two steps. TIMING CHAIN REMOVAL/INSTALLATION Warning Fuel vapor is hazardous.
How do you remove a camshaft cap from a car?
The cylinder head and the camshaft caps are numbered to make sure they are reassembled in their original position. When removed, keep the caps with the cylinder head they were removed from. Do not mix the caps. Loosen the camshaft cap bolts in several passes in the order shown. Loosen the cylinder head bolts in several passes in the order shown. 1.
What to do with a Mazda 6 engine?
1. Remove the timing chain. (See TIMING CHAIN REMOVAL/INSTALLATION.) 2. Remove the ignition coil. (See IGNITION COIL REMOVAL/INSTALLATION.) 3. Remove the high-tension lead. (See HIGH-TENSION LEAD REMOVAL/INSTALLATION.) 4. Disconnect the generator, but do not remove it from the vehicle.
How do you change a cylinder head on a Mazda 6?
1. Measure the length of each cylinder head bolt. Replace any that exceed maximum length. 2. Tighten the cylinder head bolts in the order shown using the following 5 steps. 1. Set the cam position of the No.1 cylinder at the top dead center (TDC) and install the camshaft.
What do you remove from a Mazda B2600?
Remove the alternator and accessory belts. Rotate the crankshaft to bring No.1 piston to TDC, on the compression stroke. Mark and remove the distributor. Remove the crankshaft pulley. Remove the water pump assembly. Remove the cylinder head.
1. Set the cam position of the No.1 cylinder at the top dead center (TDC) and install the camshaft. 2. Temporarily tighten the camshaft bearing caps in two or three even movements. 3. Tighten the camshaft cap bolts in the order shown using the following two steps. TIMING CHAIN REMOVAL/INSTALLATION Warning Fuel vapor is hazardous.
1. Remove the timing chain. (See TIMING CHAIN REMOVAL/INSTALLATION.) 2. Remove the ignition coil. (See IGNITION COIL REMOVAL/INSTALLATION.) 3. Remove the high-tension lead. (See HIGH-TENSION LEAD REMOVAL/INSTALLATION.) 4. Disconnect the generator, but do not remove it from the vehicle.
Why did my Mazda 6 diesel break down?
Oil level rises between services. Some is expected because of the DPF. – 32 000km car breaks down – oil warning light. Issue is very likely related to rising oil level. Car is towed to Mazda with no fault found – Oil level continues to rise so I do my own oil change at 37 000.
How often do I have to change the oil on my Mazda 6?
– 50 000 oil is dangerously high again, Mazda won’t agree to pay for the oil change. So as it stands I’m getting 4000km before the oil is at the X mark on the dipstick. This is nothing like the 10 000km interval. My driving is 40km commute twice daily on the freeway with flowing traffic.
How to record an oil change on a Mazda 3?
Record oil change in your records. (remember to keep your receipts for parts to ensure Mazda will honor the warranty in case you ever have a problem with the engine.) It looks like your drain plug already has a washer on it. Sometimes the washer is painted black from the factory as it appears in your picture.