What to do if your Honda ABS light keeps coming on?
Turn the ignition switch off, remove the key and disconnect the jumper wire from the OBD connector. If the ABS light comes back on again after step #7, do the entire procedure again, it may take a few tries to get the fault codes to clear.
How to fault reset Honda ABS and VSA?
Honda ABS / VSA Fault Reset Procedure: Turn the Ignition switch OFF and take the key out. Short pins 4 and 9 on the OBD connector located under the dash on the driver side. Now put your foot on the brake pedal and hold it down lightly while turning on the ignition switch to position “II” (all the dash lights come on, but don’t start it).
Where are the short pins on a Honda dash light?
Turn the Ignition switch OFF and take the key out. Short pins 4 and 9 on the OBD connector located under the dash on the driver side. I used a paper clip, but any stiff (solid) light gauge wire will do. Click on the photo below right to expand and you can see the pin numbers marked in the plastic.
Can a Honda door open with the VSA light on?
If you turn the power door slide switch to OFF (see photo right), it is possible to manually open the door while the engine is running even with the ABS/VSA light illuminated. Note that the door will still close electrically with the engine running as long as the slide switch is ON.
When does the ABS warning light come on?
Anytime a problem occurs in the ABS brake system the warning light gets on. In fact, ABS light stays on unless you fix the core issue. Basically, the warning light alerts the driver that the safety system is no longer active.
What does a flashing ABS light on a motorcycle mean?
If you have a flashing ABS light on your motorcycle it’s not usually a big deal, it probably just means you have a sticking rear brake lever assembly. Clean…
Turn the ignition switch off, remove the key and disconnect the jumper wire from the OBD connector. If the ABS light comes back on again after step #7, do the entire procedure again, it may take a few tries to get the fault codes to clear.
Anytime a problem occurs in the ABS brake system the warning light gets on. In fact, ABS light stays on unless you fix the core issue. Basically, the warning light alerts the driver that the safety system is no longer active.
Honda ABS / VSA Fault Reset Procedure: Turn the Ignition switch OFF and take the key out. Short pins 4 and 9 on the OBD connector located under the dash on the driver side. Now put your foot on the brake pedal and hold it down lightly while turning on the ignition switch to position “II” (all the dash lights come on, but don’t start it).
If you have a flashing ABS light on your motorcycle it’s not usually a big deal, it probably just means you have a sticking rear brake lever assembly. Clean…
What are the warning lights on a Honda?
The following are warning lights and indicators found in vehicles built by Honda. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray).
Why does my ABS brake light keep coming on?
Adjust a few times and see if the light goes off. During your ABS brake light inspection, you will want to check the levels in your brake reservoir to see if it has lost a substantial amount of brake fluid. The warning light can come on from low levels of the fluid in the brake system.
What does the ABS warning light mean on my car?
What the ABS light means. If the computer notices any abnormal signals, or the lack of a signal from any of the sensors, it will turn the ABS light on, to alert the driver of an issue. In addition to monitoring the wheel speed sensors, the computer can turn the ABS light on for other reasons like low brake fluid levels or a blown fuse.
How do I clear trouble codes on my abs light?
Connect the scan tool’s data cable to the diagnostic data port. Power on the scan tool and choose “ABS” from the scan tool’s main menu. Choose “Trouble Codes” from the ABS menu. Select “Clear All Current and Stored Trouble Codes” from the Trouble Codes menu.
Why does the ABS warning light stay on?
In fact, ABS light stays on unless you fix the core issue. Basically, the warning light alerts the driver that the safety system is no longer active. So let’s find down how ABS system works and learn how to turn off ABS light now! How Does An ABS System Work? Anti-lock brake system (ABS) is very familiar to modern cars.
How is the ABS light different from the brake light?
The ABS light differs from the BRAKE light as it is usually controlled by a computer module. When this light is on, there are often trouble codes stored to help the owner or a technician diagnose the source of the fault in the anti-lock braking system. The BRAKE light on most vehicles is activated by…