What kind of key does a Pontiac G6 have?
Pontiac non-transponder keys are metal keys that have no chip in them. Therefore, no programming is needed. The Pontiac G6 has none of this key type – the only Pontiac G6 key has a chip and needs to be programmed. These keys, also known as remote smart keys, intelligent keys or key fobs, and transponder keys, have a security chip.
Why does my G6 not start when I turn the key?
This just means that the engine doesn’t move when you turn the key. The second way that your G6 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own. When the engine isn’t turning over at all, that’s a bit easier to diagnose than when it is cranking but not firing.
When did the Pontiac G6 model come out?
Pontiac G6 was introduced in 2005. This model has one type of key: Transponder Chip Key: 2005-2010 – One type of key. Please keep in mind that some keys/remotes may look the same but they have different capabilities/frequencies/keyways and therefore it is important to have the right key/remote.
Do you need a transponder for a Pontiac G6?
None – The only Pontiac G6 key is a transponder and needs to be programmed. Keys in this category, such as remote smart keys, intelligent keys or key fobs, as well as transponder keys, have a security chip in them, which requires programming.
What’s the ignition code on a Pontiac G6?
Pontiac G6 P1682 ignition circuit code SOLVED! – YouTube Pontiac G6 P1682 ignition circuit code SOLVED! If playback doesn’t begin shortly, try restarting your device.
How does the ignition switch work on a GM car?
In this vintage, GM uses the ignition switch as a signaling device to tell the body control module the position of the lock cylinder. There’s one voltage when the key is in the lock position, another when it’s in the START, and a third when it’s in the RUN position. But the BCM should never see voltage when the key is in the ACC position.
How long do you leave ignition key on while programming?
Connect a battery charger to the battery to ensure power is available while programming. Both the BCM and PCM must be working and communicating with each other. Insert ignition key and turn to the “ON” position. Do not attempt to start the engine. Leave the key in the “ON” position for approximately 11 minutes.
What to do if you lost your Pontiac G6?
Generally speaking, you have three options: First, call an automotive locksmith that offers a mobile service for Pontiac G6 cars. We can help you with this option. Second, have your car towed to an official dealer. Third, order a key online and have the dealer or locksmith cut and program it (if necessary) for you.
How to program a replacement key fob for a 2007 Pontiac G6?
I was just curious if anybody here has experience in reprogramming a key fob for a 2007 Pontiac G6. The car seems to have a Vehicle Theft Protection system, because it engages when I lock up the car, but it doesn’t trigger when I mess with the door handle, not sure if thats important but I’m throwing it in there.
What’s the problem with my 2007 Pontiac G6?
2007 Pontiac G6 Convertible issue, driver’s side middle latch won’t open. Any way to have HVAC remember the setting used for Vent or Recirculate? Torque Damper!!!! 2008 G6. Need help on how to remove hood emblem.
What does mall stand for in Pontiac G6?
Pontiac called it MALL/PGM in the grand prix/sunfire/sunbird, etc… in the G6 apparently changed names… I found online a guy claims the MALL/PGM stands for “Multifunction Alarm Lock and Lighting” and PGM = “Programming”… that said in our cars, as you found no such label…
How to program a new car key fob?
Refer to Electronic Diagnosis in Body and Chassis. Turn the ignition lock cylinder to the ACC position. Turn the ignition lock cylinder OFF, then back to ACC within 1 second. Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode.