What kind of brake pads does Mercedes GL450 use?
This article is relevant to 2007-2012 GL450 as well as GL320, GL350 and GL550. As for the parts, I used Zimmerman coated rotors, Jurid front pads and Textar rear pads. For some reason Mercedes used Jurid pads as OEM in the front and Textar in the back. Torque wrench. Torque angle wrench. C-Clamp.
How to remove brake rotor from Mercedes GL350?
Use a T30 bit to remove the brake rotor set screw. Remove and discard the brake rotor. If the rotor is rusted on to the hub, you will need to whack it with a hammer from the back a few times. 9. Once the rotor is removed, use a wire brush to clean the rust off the hub. 10. Lubricate the center of the hub with some anti-seize. 11.
Can you replace brake pads and rotors at the same time?
Many professionals and mechanics would recommend that both elements of the brake system be replaced at the same time, but occasionally the owner may be able to just replace the brake pads without the rotor if the rotor isn’t showing as much wear and tear.
What causes brakes to shimmy right after rotor and pad?
The shimmy feeling that comes from brakes is usually due to uneven friction material build-up on the rotor. This transfer from pad to rotor is supposed to happen, indeed it makes the brakes work better, which is why brakes function better after break-in.
This article is relevant to 2007-2012 GL450 as well as GL320, GL350 and GL550. As for the parts, I used Zimmerman coated rotors, Jurid front pads and Textar rear pads. For some reason Mercedes used Jurid pads as OEM in the front and Textar in the back. Torque wrench. Torque angle wrench. C-Clamp.
Use a T30 bit to remove the brake rotor set screw. Remove and discard the brake rotor. If the rotor is rusted on to the hub, you will need to whack it with a hammer from the back a few times. 9. Once the rotor is removed, use a wire brush to clean the rust off the hub. 10. Lubricate the center of the hub with some anti-seize. 11.
What to do if your brake rotor is worn out?
A worn out rotor will have a lip that will prevent the caliper from being removed. Use a C-Clam to compress the caliper pistons. Check your brake fluid level after compressing each caliper to make sure it doesn’t overflow. 6. To avoid damaging the brake hose, hang the caliper. 7. Remove the caliper bracket.
How do you change the brake caliper on a Mercedes?
1. Start out by jacking up the SUV, removing the wheels and safely supporting the SUV on the jack stands. 2. Unbolt the brake wear sensor connector from the caliper and disconnect the wear sensor. 3. Remove the brake caliper anti-rattle clip.
How to remove brake caliper from Mercedes GL350?
Start out by jacking up the SUV, removing the wheels and safely supporting the SUV on the jack stands. 2. Unbolt the brake wear sensor connector from the caliper and disconnect the wear sensor. 3. Remove the brake caliper anti-rattle clip. 4. Unbolt the two caliper guide pins and remove them from the bushing.
Do you need to replace brake pads on a Mercedes?
Install the new Mercedes wear brake sensor on the new pads. You can reuse old wear sensor if the sensor wires are not exposed. If the brake pad wear sensor wires are exposed or you had a warning on your instrument cluster stating “Brake pad wear”, you will need a new sensor. Install new Mercedes rear brake pads.
Can you change brake pads on a Japanese car?
Fits most European and Japanese cars… Once your pistons are pushed in, you can now replace the brake pads. Ensure you lubricate any moving parts and clean everything not to get stuck, so you have to redo the job soon. Replace any metal plates if you got them in the brake pads package.
When to change rotors on Mercedes Benz brakes?
Most MB dealers will recommend a rotor replacement when changing brake pads if they feel the wear on the rotors is at the point where the rotors will wear past their minimum limit BEFORE the replacement brake pads are worn because the brake wear warning on the cars only warns of worn brake pads.
When do you need to replace your brakes?
Most vehicles should have their tires rotated at least every six months, and that is a good time to have the brakes inspected, as well. A mechanic can check the thickness of the pads and the condition of the calipers or drum hardware to spot wear. Many cars have built-in wear sensors that scrape against a brake disc when the pads needed replacing.
Most vehicles should have their tires rotated at least every six months, and that is a good time to have the brakes inspected, as well. A mechanic can check the thickness of the pads and the condition of the calipers or drum hardware to spot wear. Many cars have built-in wear sensors that scrape against a brake disc when the pads needed replacing.
How many miles does a car brake pad last?
With all that in mind, brake pads typically last anywhere from 35,000 to 60,000 miles, depending on the above factors. What’s maybe more important to know, though, is the warning signs that you do need new brakes .
How much does it cost to change brake pads on a Mercedes?
The typical cost to change Mercedes-Benz rear brake pads yourself averages $100. The average cost to change the brake pads at an auto mechanic or dealer range between $250 and $500. If you plan to replace the rotors, the cost would be two to three times more than just changing the brake pads.
What should the torque be on a Mercedes brake pad?
The typical torque range is between 30 and 55 Nm and varies between models. Call your dealer to get the recommended torque specifications for your Mercedes-Benz. Connect the brake pad wear sensor.
How do you change the parking brake on a Mercedes?
If you are changing the rotors, remove the two 18 mm bolts that secure the rear wheel assembly’s bracket. Remove the T30 screw from the rotor. Release the rear parking brake. Once you remove the screw, you can remove the rotor. If the rotor is rusted, it may difficult to remove.
The typical torque range is between 30 and 55 Nm and varies between models. Call your dealer to get the recommended torque specifications for your Mercedes-Benz. Connect the brake pad wear sensor.
How to replace front brake pads and rotors?
Measuring rotor thickness. To make this how-to more organized, the front brake pad and rotor replacement will be covered first. Lift your vehicle up and support it on jack stands. Your W204 has several jacking points that can be used, including the rear differential, the front subframe and the side jack stand mount pads.
Where do you put the brake spreader on a Mercedes?
If your Mercedes-Benz has electronic parking brakes, you will need to place the rear brakes in service position via the instrument cluster. If you don’t have a brake spreader, use a flat head screwdriver to push the piston in, as shown in the picture below.
If you are changing the rotors, remove the two 18 mm bolts that secure the rear wheel assembly’s bracket. Remove the T30 screw from the rotor. Release the rear parking brake. Once you remove the screw, you can remove the rotor. If the rotor is rusted, it may difficult to remove.
If your Mercedes-Benz has electronic parking brakes, you will need to place the rear brakes in service position via the instrument cluster. If you don’t have a brake spreader, use a flat head screwdriver to push the piston in, as shown in the picture below.
The typical cost to change Mercedes-Benz rear brake pads yourself averages $100. The average cost to change the brake pads at an auto mechanic or dealer range between $250 and $500. If you plan to replace the rotors, the cost would be two to three times more than just changing the brake pads.
What are the common problems with the Mercedes GL450?
I am planning a purchasing a used GL450, but want to know what the common problems with the vehicle are. The SUV will be around 100k miles. If you can also give me an estimated price for the fixing of the common problems that will also be helpful.
How many miles is a Mercedes GL 450?
The SUV will be around 100k miles. If you can also give me an estimated price for the fixing of the common problems that will also be helpful. Also is it worth to get a third party used car warranty on it and if so what do you recommend. Estimate repair costs?
1. Start out by jacking up the SUV, removing the wheels and safely supporting the SUV on the jack stands. 2. Unbolt the brake wear sensor connector from the caliper and disconnect the wear sensor. 3. Remove the brake caliper anti-rattle clip.
A worn out rotor will have a lip that will prevent the caliper from being removed. Use a C-Clam to compress the caliper pistons. Check your brake fluid level after compressing each caliper to make sure it doesn’t overflow. 6. To avoid damaging the brake hose, hang the caliper. 7. Remove the caliper bracket.
What to do when the brake pad wear indicator warning light is on?
What to do when the brake pad wear indicator warning light is on. If the light comes on, you should bring the vehicle to a certified technician to have the brakes replaced. More than likely, the light will shut off with the new pads installed. However, any issues with the sensors themselves will cause the light to turn on.
Start out by jacking up the SUV, removing the wheels and safely supporting the SUV on the jack stands. 2. Unbolt the brake wear sensor connector from the caliper and disconnect the wear sensor. 3. Remove the brake caliper anti-rattle clip. 4. Unbolt the two caliper guide pins and remove them from the bushing.
Is it safe to drive with brake pad light on?
It is safe to drive with this light on for a short amount of time. As mentioned earlier, the light will come on when you still have some brake pad material left, but if you wait too long and continue driving, you will run out of material and damage the rotors.
What are the warning lights on a Mercedes Benz?
The following are warning lights and indicators found in vehicles built by Mercedes Benz. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are over 40 of them so be patient!
What to do when the brake pad wear indicator warning light is on. If the light comes on, you should bring the vehicle to a certified technician to have the brakes replaced. More than likely, the light will shut off with the new pads installed. However, any issues with the sensors themselves will cause the light to turn on.
How does the brake wear sensor work on a Mercedes Benz?
The brake wear sensors have two wires running to contacts embedded in plastic within them. The sensors are triggered when the pads (and thus the plastic of the wear sensors) wear down to the point where the two wires feeding into / out of them created a CLOSED circuit (or short) through the brake rotor.
It is safe to drive with this light on for a short amount of time. As mentioned earlier, the light will come on when you still have some brake pad material left, but if you wait too long and continue driving, you will run out of material and damage the rotors.