What does p0017 mean on a GMC Acadia?
P0017 refers to which camshaft position sensor is out of time with the Crankshaft. In this case it’s sensor “B”, Sensor “A” throws P0016 P0017 Symptoms: GMC Acadia P0017 should be considered an important trouble code to diagnose and repair.
What causes a GMC Chevy 3.6L p0008 p0017 p0019?
In some instances these codes can also be caused by low or dirty oil or a plugged or failed valve valve timing solenoid when should be always be checked first. GM has extended the warranty on their timing chains to 120000 Miles and 10 years.
How much does it cost to diagnose GMC code p0008?
The cost to diagnose the P0008 GMC code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
What does trouble code p0016 p0017 mean?
In this case it’s sensor “B”, Sensor “A” throws P0016 P0017 should be considered an important trouble code to diagnose and repair. The crank and cam sensors work in tandem to produce the ideal air/fuel ratio for your engine.
P0017 refers to which camshaft position sensor is out of time with the Crankshaft. In this case it’s sensor “B”, Sensor “A” throws P0016 P0017 Symptoms: GMC Acadia P0017 should be considered an important trouble code to diagnose and repair.
What does the code p0008 mean on a car?
What Does the Code P0008 Mean? P0008 is the result of a test run by the engine control module to check for misalignment between the camshafts in engine bank one and the crankshaft. The misalignment for this code would be at an idler sprocket in the bank or at the crankshaft.
In this case it’s sensor “B”, Sensor “A” throws P0016 P0017 should be considered an important trouble code to diagnose and repair. The crank and cam sensors work in tandem to produce the ideal air/fuel ratio for your engine.
What kind of engine code is p0009?
Bank one is the engine is the bank that includes cylinder one. P0009 is the equivalent code for bank two. Although this code can be set by any OBD-II equipped vehicle, it is most common in Suzuki, GM, Cadillac, Buick, Holden, Chevrolet, and GMC vehicles.
What does the OBD code p0017 mean?
What the P0017 code means. P0017 is the OBD-II generic code indicating that the crankshaft and camshaft position sensor for bank 1 exhaust camshaft do not correlate signals with each other.
What kind of magnet is a p0017 GMC?
P0017 GMC Meaning The Crankshaft Position (CKP) sensor is a permanent magnet generator, known as a variable reluctance sensor. The magnetic field of the sensor is altered by a crankshaft mounted reluctor wheel that has seven machined slots, 6 of which are equally spaced 60 degrees apart.
How much does it cost to repair a p0017 GMC?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost of diagnosing the P0017 GMC code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.
What are the symptoms of engine code p0008?
If the Engine Control Module (ECM) detects that the bank 1 camshaft and crankshaft are not in the correct position, it will trigger code P0008. What Are The Symptoms Of Code P0008?* What Is The Cause Of Code P0008? How Serious Is Code P0008? – Severe This trouble code can cause the vehicle to be hard to start and run rough.
What does p0008 mean on an ECM?
It does this by monitoring them using the Camshaft Position Sensor (s) and Crankshaft Position Sensor. If the Engine Control Module (ECM) detects that the bank 1 camshaft and crankshaft are not in the correct position, it will trigger code P0008.
What to do if your check engine light says p0008?
Check to see if there are any other codes along with P0008 and clear your Check Engine Light with FIXD. Check the freeze frame data in order to pinpoint the issue. Check for any Technical Service Bulletins (TSB) General Motor vehicles (GMC, Chevrolet, Buick, Suzuki, Cadillac, Holden) specifically have a known issue with stretched timing chains.
What do you need to know about error code p0008?
For error code P0008, one or more of the below repairs may be needed to solve the underlying issue. For each possible repair, the estimated cost of repair includes the cost of the relevant parts and the cost of labor required to make the repair.
P0017 GMC Meaning The Crankshaft Position (CKP) sensor is a permanent magnet generator, known as a variable reluctance sensor. The magnetic field of the sensor is altered by a crankshaft mounted reluctor wheel that has seven machined slots, 6 of which are equally spaced 60 degrees apart.
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost of diagnosing the P0017 GMC code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.
How to diagnose a p0014 GMC code?
Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P0014 GMC code is 1.0 hour of labor.
Why does my Acadia not run when the crank is off?
The crank and cam sensors work in tandem to produce the ideal air/fuel ratio for your engine. When this timing is off, the engine will typically not run (or barely run). Here are the major symptoms of P0017 in the Acadia:
What happens if you misdiagnose the u0184 fault code?
Misdiagnosis has been known to occur if you diagnose the U0184 code before any of the basic codes have been thoroughly diagnosed and dismissed. If your scan tool can access fault codes and the only one you get from other modules is the U0184, try to access to the radio (Radio).
What does the trouble code OBD-II mean?
This is a generic communication system diagnostic trouble code that applies to most OBD-II vehicle makes and models. This code means that the Radio (Radio) and other control modules on the vehicle are not communicating with each other.
Are there any problems with the GMC Acadia?
Many of the secondary systems and other components of the GMC Acadia have faced problems over the years depending on the model year. The air conditioning system, for instance, was an issue for some drivers in 2012 and there were problems with it blowing hot air into the cabin.
The crank and cam sensors work in tandem to produce the ideal air/fuel ratio for your engine. When this timing is off, the engine will typically not run (or barely run). Here are the major symptoms of P0017 in the Acadia:
When to set DTC c0161 in Acadia?
• DTC C0161 will be set if the brake is applied for 60 seconds while at speeds greater than 10 km/h (6 MPH), such as a two footed driving. Note: If the ABS, and/or Traction Control indicators are ON with DTC C0161 set in history, perform the conditions for clearing the DTC and inform the customer that two footed driving set this DTC.
What does the DTC code p0017 stand for?
Code P0017 means that your car’s powertrain control module detects a misalignment between the crankshaft and camshaft positions. What Does the P0017 Code Mean? Diagnostic trouble code (DTC) P0017 stands for “Camshaft Position B – Camshaft Position Correlation (Bank 1).”
What causes the p0017 code on the ECM?
Technicians will use an oscilloscope to examine the crank and cam sensor pattern the ECM/PCM is reading while the engine is running. A damaged timing chain or belt can trigger code P0017. What are the Possible Causes of the P0017 Code?
Are there any recalls on GMC Acadia 2007?
After googling P0017 and seeing all the posts on the forum about the timing chain issues, it jogged my memory about the recall notice (for the extended warranty on the chains for the 2007 models) I received much earlier this year, but I can no longer locate. So I brought it in to the Dealership a few weeks ago.
Why does my GMC Acadia keep throwing code?
My basic mechanical understanding leads me to believe that the cam and crank shaft aren’t in time and that’s what’s throwing this code. Fast forward to now, a few weeks later, and suddenly the car is idling bad. At idle it will the engine RPMs are “surging”.
In some instances these codes can also be caused by low or dirty oil or a plugged or failed valve valve timing solenoid when should be always be checked first. GM has extended the warranty on their timing chains to 120000 Miles and 10 years.
My basic mechanical understanding leads me to believe that the cam and crank shaft aren’t in time and that’s what’s throwing this code. Fast forward to now, a few weeks later, and suddenly the car is idling bad. At idle it will the engine RPMs are “surging”.
How much does it cost to repair a p0008 GMC?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost of diagnosing the P0008 GMC code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.
What are the symptoms of engine code p0017?
Code P0017 may be accompanied by several different symptoms. These including: an engine that runs poorly, an engine that cranks but will not start and an illuminated check engine light. How do you troubleshoot code P0017 ? Perform a visual inspection of the sensors and connections. Many problems can easily be found in the harness and connectors.
What is the diagnostic code for a GM V6?
Crankshaft position (CKP)/Exhaust camshaft (CMP) correlation Bank 1 (RH) This code points to a misalignment between the exhaust camshaft on bank 1 and the crankshaft. Most probable cause is one or more stretched timing chains – Most likely being the bank 1 sub chain.
What to do if diagnostic code P008 is not present?
If codes P008 and P0009 are not present, you will need to connect factory equivalent scan tool to monitor camshaft position on the affected bank. You must then actuate the correct VVT solenoid with engine at idle. If idle does not change significantly, you likely have a VVT solenoid failure.
What does the p0018 code in OBD-II mean?
All our repairs are backed by our 12-month / 12,000-mile warranty. P0018 is the OBD-II generic code indicating that the camshaft position sensor A for bank 2 does not correlate to the signal from the crankshaft position sensor. What causes the P0018 code? The bank 2 intake camshaft is out of position compared to the crankshaft position.
What’s the difference between p0016 and p0018?
Code P0018 is the same as code P0016 except for the opposite side of the motor. If both codes are present then suspect the oil pressure is low or not getting to the OCV for both camshafts. Need help with a P0018 code? YourMechanic offers certified mobile mechanics who will come to your home or office to diagnose and repair your vehicle.
If codes P008 and P0009 are not present, you will need to connect factory equivalent scan tool to monitor camshaft position on the affected bank. You must then actuate the correct VVT solenoid with engine at idle. If idle does not change significantly, you likely have a VVT solenoid failure.