What does it mean when SRS warning light stays on?

SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system. It is very unlikely that your airbags are going to deploy randomly, but the concern is that they may not deploy…

What does the SRS light mean on a Mercedes Benz?

What does SRS light mean? SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system.

Why is the SRS light on my car yellow?

The connectors of an airbag system are often yellow. When you are moving the seats forward and backwards the connectors will move a little bit everytime, and it may cause bad connections between the airbag control unit and the airbags/seatbelt airbag and it will cause an error code.

Is there a SRS light on my Honda Landrover?

This May Fix it! – MG Rover Landrover Freelander Honda? – YouTube SRS Light On? This May Fix it! – MG Rover Landrover Freelander Honda? If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

Is there a way to reset the SRS light?

You can’t rest the airbag SRS light with a simple OBD II scanner which gives you the check engine light codes. You will need a more advanced scan tool to reset the airbag light. For around $110-150, which is how much a diagnosis costs anyway, you can get your airbag reset tool.

What does the SRS light on new Rover 400 mean?

For the EC3 system on New Rover 400, the airbag warning light has the following meaning. Warning light behavior when ignition is switched on. Comes on then goes off after 3 seconds. For the Honda SRS system used on Rover 600 and New Rover 400, the airbag warning light has the following meaning. Warning light behavior when ignition is switched on.

What does the red warning light mean on a Land Rover?

Engine Temperature WARNING LIGHT (RED) This dashboard symbol illuminates due to the engine temperature being too high. A message on the display centre will read ENGINE OVERHEATING. Stop the vehicle as soon as possible as engine damage is likely to occur.

Can a MOT fail if the SRS light stays on?

It was changed so if the light comes on and stays on during the test then it will be an mot fail but it can’t be failed for the sequence of the light ie start car light stays on for 5s then goes out so if you take the bulb out you can’t fail it but im pretty sure that the abs light is different and must show the correct sequence.

What does it mean when your SRS light comes on?

When your SRS light occurs, it means that you have an error stored in your airbag system and you have to fix it as soon as possible. Your airbag system contains an airbag control unit, several crash sensors and several airbags. The crash sensors are mounted in the front and the side of your car, some cars have more crash sensors.

Is it safe to drive with SRS light on?

While you can certainly drive while your SRS light is on, it isn’t safe. You should get your vehicle to a service center as soon as possible so that a technician can inspect your SRS computer.

Which is the best scanner to reset the SRS light?

Our favorite scanner that will read and reset your SRS / airbag light is the iCarsoft i980 for Mercedes-Benz which will retrieve the SRS light but also the check engine.

Why does my car not start after shorting out the SRS light?

To make a long story short my car wouldn’t start after shorting out the SRS light when you short the SRS it fries your main control module under the steering wheel which will cause your car to not start. Never Short out anything Electronic it will not fix the problem it will make the situation worse. Was this answer helpful?

How to turn off the ” maint reqd ” light?

Turning Off “MAINT REQD” Light Toyota Sienna, Corolla, etc. – The MAINT REQD light goes on (first blinking, then persistent) to indicate it’s time to change the engine oil. However, after changing the engine oil, the light stays on. I thought the act of changing the oil was enough to reset the warning, but not so.

When does the maint REQ’D light go out?

When the mileage driven reaches between 8,000 to 10,000 miles, the MAINT REQ’D light will illuminate for 2 seconds and then blink on and off for 10 seconds then it’ll go out. When the mileage driven exceeds 10,000 miles the MAINT REQ’D light will illuminate and stay on as long as the ignition switch is in the ON position.

How to reset maintenance required light ( 2001-2005 )?

If the lights are on, the MAINT REQ’D light will not reset. If your Civic is equipped with daytime running lights (DRL), the DRL must be disabled so the MAINT REQ’D light can be reset. These are the steps: Turn the ignition switch to the OFF position.

Is there a scanner that reads the SRS light?

Here is a scanner that works with Mercedes-Benz and will rear fault codes and reset the AirBag, ABS and check engine light. Our favorite scanner that for an in-depth Mercedes-Benz troubleshooting is the iCarsoft MB II. Not only does it read the SRS light (Airbag Control Unit) but also every control unit in your Mercedes-Benz.

How long does it take for the SRS light to flash?

The SRS light will flash for exactly seven seconds. Once it turns off, immediately switch your ignition off. Wait for three seconds and then turn on your ignition again. Repeat the entire process for two or three more times. If successful, your SRS light will start flashing.

What is SRS light?

The SRS light is a warning light for your supplemental restraint system (airbags). An SRS light means that there is a problem in the system.

What does SRS light mean?

An SRS light means that there is an error stored in your airbag system. Your airbag system will be out of function if your SRS light is on and will not deploy in case of an accident. Always fix your airbag system as soon as possible.

What is a SRS code?

This is important because the ABS system helps assist your vehicle with maintaining control during stops. The SRS system is the system in your vehicle that deals with Airbags for your safety. An SRS code can be vital in telling you if your Airbags are working in the event of an accident.

What does it mean when SRS light is on?

The SRS light indicates a problem with the seatbelt or the airbag system. If you drive it with the light on, chances are that the airbags will not deploy if an accident were to happen. Airbags can reduce the force and slow down the impact. However, they are useless if they don’t deploy.

Why does the SRS / airbag light stay on?

Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Install a new battery; Reset SRS/ Airbag light.

How can I get rid of the SRS light?

You can get rid of the SRS light in one of the following ways: If you do not like the idea of taking your car to a mechanic then you can buy a scanner with SRS capability and use it to reset the light. Make sure to find a tool that supports this feature as not all OBD-II devices may have this option.

How do you remove an SRS airbag warning light?

Hold the center section of the wheel in place — where your airbag is located — and locate the screws. Unscrew them. Step 3: Once the screws have been unscrewed, pull the airbag towards you and remove the connectors. Use a pick to slide the yellow clips out in order to remove the connector. You can now remove the airbag.

What does the warning light SRS mean?

The SRS light is a warning light that indicates an issue with the airbags system. Since it’s linked to the airbags, it’s also commonly known as the airbag light. In most cars, it looks like a side view of the driver or passenger in a seat with the seat belt on.

What does it mean when the SRS warning light comes on?

The SRS light is a warning light for your supplemental restraint system (airbags). An SRS light means that there is a problem in the system. This is a air bag fault light .it comes on when you have a fault in the air bag system. The SRS light is for the “Safety Restraint System” (Airbags).

What caused the SRS light to come on?

There are a few reasons why the SRS light turns on. One of the most common reasons the airbag light turns on is because there is an interference happening with the seat belt and the sensor. This causes the warning light to falsely come on. The next reason the SRS light might be on has to do with the passenger’s seat.

Why does the SRS light stay on?

If you see the SRS light on, you must work to know why. It can be due to a variety of reasons including: The malfunctioning of airbag sensors: It is common for the sensors to fail. This may cause the sensor to activate all of a sudden for no reason, causing the airbag light to stay on. Replacing the sensors may do the job.

Where is the SRS restraint system dash light located?

This warning has reappeared one other time and I repeated the cleaning process with the same result. This connection is quite sensitive and since it is located right at the front of the seats and just off the floor, it is very vulnerable to foot traffic and thus dust/dirt.

What does the SRS light mean on a Honda Accord?

The SRS light is a warning light for your supplemental restraint system (airbags). An SRS light means that there is a problem in the system. The first thing I would check is the fuse for the SRS unit. The only way to check this is with a scan tool of some sort. I used a Solus Pro.

Where is the SRS light on the dash?

If the red SRS lamp on the dash is accompanied by the orange airbag lamp next to the transmission shifter is lit, the fault is commonly connected to the passenger seat sensor.

What does SRS malfunction mean?

HI, SRS malfunction means that a fault has been detected in the Safety Restraint System by the SRS control module. The system continuously goes through a series of checks and when a fault is detected in the system it will turn the warning light on. This system includes your seat belts and air bags.

Why does the airbag light stay on?

Light stays on and warning for airbag service on reader board. If the airbag light stays on after it completes it’s “check light” process then there is a fault in the air bag system. It could be anything from a bad sensor (there are 3 of them) to a wire that has become unplugged. This problem should be repaired as soon as possible because…

What does the SRS light mean on Mercedes?

SRS stands for Supplemental Restraint System . If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system. It is very unlikely that your airbags are going to deploy randomly, but the concern is that they may not deploy at all in a case of an accident.

Where is the reset button on a SRA?

Use a narrow, straight object, like a straightened paper clip or a toothpick, to press and hold the reset button on the SRA appliance for five to ten seconds. The reset button is in a small hole next to the console port.

What to do when the SRS light stays on?

If your SRS light stays on because of an issue with the airbags themselves, an experienced technician will scan the computer system in your car to find the exact problem and repair the broken or malfunctioning parts. The experienced technicians at My Auto Solutions can fix any problem that is causing your SRS light to stay on.

What does the SRS light on airbags mean?

What does the SRS light on a Honda do?

The secondary restraint system, or SRS, is a safety system in your Honda that controls the airbags, among other things. You would imagine that when the SRS light comes on, that it would be a big deal and need to be checked out immediately.

What do you need to know about SRS system?

Airbags contain perchlorate material which required special handling. Air bags and Emergency Tensioning Devices (ETD) are designed to function one time only. Once these systems deploy they must NOT be reused. If you work on the SRS system, you should disconnect the battery. Do not use seat covers unless approved by Mercedes-Benz.

Is it safe to drive with the SRS light on?

Can You Drive With the SRS Light On? Your vehicle will still operate with the SRS light on. However, it’s not safe to drive with a malfunction in the airbag system. We recommend getting to the service station immediately to find out what the problem is.

Why is the SRS light blinking after ignition?

SRS light is blinking after ignition. The SRS light indicates a problem with the seatbelt or the airbag system. If you drive it with the light on, chances are that the airbags will not deploy if an accident were to happen. Airbags can reduce the force and slow down the impact. However, they are useless if they don’t deploy.

Where is the reset SRS light on a Mercedes Benz?

Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver’s side of the car.

Why does my SRS light keep going on?

When does the SRS airbag light come on?

The airbag light will be blinking for seconds after the ignition if there is any trouble. This system is working to check the airbags for drivers, passengers and sides airbags, including the modulator, inflation, and wiring.

What causes the SRS warning light to come on?

The SRS computer in your vehicle has a backup battery that enables it to retain its data, even when your vehicle’s power is cut off. A low or drained car battery can cause the SRS backup battery to get too low. When this happens, the warning light will come on.

How does SRS improve deliverability of applicable messages?

This SRS change improves deliverability of applicable messages that pass Sender Policy Framework (SPF) checks when they arrive from the original sender but that then fail SPF at the final external destination after they are forwarded. SRS rewrites the P1 From address in the following scenario:

How is an email address rewritten in SRS?

The address is rewritten by using the following pattern: In order to receive NDRs for relayed messages that are rewritten by SRS, a mailbox (either hosted or on-premises) must be created by using the username of “bounces” and by having the domain be set as the default Accepted Domain of the customer.

What to do if your SRS is not working?

There is a malfunction in the left-hand and/or right-hand window curtain air bag. The warning lamp also lights up in the instrument cluster. •► Visit a qualified specialist workshop. In the event a malfunction of the SRS is indicated as outlined above, the SRS may not be operational.

What happens when your gas gauge is not working?

The gas gauge tells you how much fuel is in your gas tank and alerts you when it’s time to refuel. If your gas gauge is not working, the inaccurate information it provides may cause you to run out of gas unexpectedly.

How does the fuel gauge on a jeep work?

The fuel gauge on your Jeep is powered by the fuel sensor relay. If the fuel gauge in your Jeep stops working, the relay has gone bad and needs to be replaced. The fuel sensor relay is responsible for powering the sensors that, in turn, relay information to your fuel gauge.

What does a gas gauge tell you about a car?

Benjamin Jerew is an ASE-certified Master Automobile Technician with over a decade of experience in auto repair, maintenance, and diagnosis. The gas gauge tells you how much fuel is in your gas tank and alerts you when it’s time to refuel.

How does the resistance of a gas gauge change?

The fuel float contacts run on a potentiometer, or variable resistor, whose resistance changes depending on float level, effecting a change in output voltage. Some systems are wired so that high fuel level contacts the low-resistance section, gradually increasing resistance as fuel level drops.

How to troubleshoot Mitsubishi SRS airbag warning light?

Turn on the ignition and allow the scanner to power on. Select your Mitsubishi model and year. For example, in 2017, Lancer. Select SRS / Airbag Control unit from the main menu. Select Read Fault Codes. Write down all the codes and also make sure they are NOT PRESENT.

What does the SRS light on the airbag mean?

What is SRS light? In the simplest term, SRS light or the light for Supplemental Restraint System is a sensor working to indicate the status of the safety airbags in cars. The airbag light will be blinking for seconds after the ignition if there is any trouble.

What happens when the SRS light goes out?

When the vehicle is first started, the SRS light should illuminate for 1 to 5 seconds while the system goes through a self-test sequence. If the light goes out, then the system is ready. If the light stays on, there is a fault somewhere in the SRS system.

Why does the Mitsubishi SRS warning light stay on?

Mitsubishi airbag warning light stays on to notify the driver that the airbags may not deploy if you get in an accident. Airbag or SRS light stays on when the Supplement Restraint System (SRS) detects a malfunction. If the airbags don’t deploy during an accident, you or your passengers may suffer serious injuries.

Why is the SRS system called a passive restraint system?

The computer also tightens the seat belts to protect the vehicle occupants from physical harm during an impact caused by a collision. The SRS system is also referred to as a passive restraint system because the vehicle occupants do not need to do anything in order to activate the SRS system when the enabling criteria—speed and deceleration—are met.

What does the warning light at the instrument cluster mean?

What you need to know…it’s a safety issue.. Have you ever had that annoying light illuminated at your instrument cluster and wondered what it meant? The SRS warning light refers to the Supplemental Restraint System (SRS) and is most commonly known as the airbag system light.

Is the Mercedes W211 SRS restraint system defective?

Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later. Hidden Functions Mercedes.

Why is the SRS warning staying on on a Mercedes Benz?

Why is the SRS warning staying on? Here is a list of some of the most common problems with the SRS system on a Mercedes Benz. Seat Occupancy Senor in the passenger seat. Low voltage in the electrical system. Battery issue or charging. Seat belt latch. Damaged Wire Contacts at the doors. Defective, damaged or loose contact at the impact sensors.

Do you need to disconnect seat covers for SRS?

Air bags and Emergency Tensioning Devices (ETD) are designed to function one time only. Once these systems deploy they must NOT be reused. If you work on the SRS system, you should disconnect the battery. Do not use seat covers unless approved by Mercedes-Benz. Seat covers can restrict the proper operation of the airbags integrated into the seats.

What does SRS stand for in car category?

SRS is short call of Supplemental Restraint System.The SRS Airbag System is designed to supplement the seatbelt system and improve occupant protection in certain type of crushes.

What causes a change in resistance on a SRS?

A change in resistance as small as a couple tenths of an ohm could readily be caused by temperature. A changed seat position or a missing passenger could cause a resistance variant that’s the difference between the indicator lamp being on or off. For this reason you should never dismiss a resistance value that’s close to being out of spec.

How can I clear code on SRS restraint system?

Once reconnected, I was able to use the i980 unit to clear the code. This warning has reappeared one other time and I repeated the cleaning process with the same result.

What does SRS stand for on a car dashboard?

Older vehicles used the simple Supplemental Restraint System acronym, SRS. And there’s still another… Yet another version, used by some European manufacturers, is a simple Air Bag text symbol, as shown at left. All versions warn of a failure in one of the air bags, which can only be repaired by your dealer or authorized service center.

What does the SRS air bag indicator symbol mean?

Either of these warning lights indicate that a problem exists with one of the many airbags in the vehicle, which should be taken to the dealer or authorized service center as soon as possible. The picture symbol has been described as a beach ball on a lap. But first, is one of these truly your symbol?? If yes, continue on below.

What does the SRS light on the dashboard indicate?

But one of the most important signals may be a mystery until it is lit up on your dashboard: the SRS light. WHAT IS THE SRS LIGHT? The Supplemental Restraint System (SRS) is the technical name for the system that controls the airbags and automatic seatbelt restraints.

How long does the SRS warning light stay on?

While your car will run with this light on, it is important that you diagnose this problem as soon as possible. Under normal operations, when you first turn the ignition and start the car the light stays on for about 5 seconds and then turns off.

How does the SRS warning system work in a car?

SRS Warning System. The SRS system checks the operation of several components in your car such as: Airbags. Airbag control unit. Crash sensors. Emergency Tensioning Devices. Belt force limiters. Child occupancy sensor in front passenger seat.

How to read and reset SRS / airbag light?

Battery dying. How to read and reset SRS/ Airbag light? Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it.

What does SRS warning light on dashboard look like?

The SRS warning light on the dashboard usually looks like a side view of a person sitting in a seat with a seat belt on, with a large circle (the airbag) in front of the person.

How do you reset the SRS light on a Toyota?

Take a paperclip and unfold it. Jump the wire by attaching one end of the paperclip to each of the two terminals. This will reset the SRS light. Put the yellow electrical connector back in place and close the panel cover.

What does the SRS light on my SL500 mean?

Your vehicle’s restraint systems control module sits atop the transmission tunnel, and wired to it are a device in each seat for tensionsing the seat belts in the event of an accident (“ETR ignition squib”). The fault code you have indicates there is a problem with the wiring or the “driver” seat tensioning device.

Why is my SRS light on in my Mercedes C class?

A malfunctioning seat belt could cause the SRS light in your Mercedes-Benz C-Class to display on the dashboard. The same is true even if the air bags in your vehicle are safe to deploy in a crash. If your C-Class is under warranty, the dealer will replace the malfunctioning seat belt (s) at no cost to you.

What should I do if my SRS light comes on?

If you need a scanner that will also troubleshoot Transmission, ESP, ABS and any other control unit on your Mercedes-Benz, check out the iCarsoft MB II, a powerful diagnostic scanner for Mercedes-Benz cars. Want to know why the SRS light came on?

What does SRS warning light on Mercedes W204 mean?

Here’s what a solid SRS warning light could mean for your vehicle. This article applies to the Mercedes-Benz w204 (2007-2014). The supplemental restraint system (SRS) light in your vehicle will illuminate whenever there is a problem with your air bags or seat belt fasteners.

What happens when the restraint system malfunctions?

The damage was superficial -no airbag deployment but the driver’s seat belt restraint system did operate. The consequence is : 2.the driver’s seat belt buckle has shortened -part of the tensioning process. I shall get the seat belts removed.checked and repaired.

What does the power steering system warning light mean?

What the power steering system warning light means This warning light tends to be in the shape of a steering wheel, sometimes with an exclamation mark. For cars with electric power steering, the light may say EPS, for electric power steering. Either way, the warning light will be yellow or red in color.

Why is the SRS light on my front seat yellow?

A really common case is the connectors under your front seats. The connectors of an airbag system are often yellow. When you are moving the seats forward and backwards the connectors will move a little bit everytime, and it may cause bad connections between the airbag control unit and the airbags/seatbelt airbag and it will cause an error code.

How do you reset the SRS light on a Silverado?

How to Reset the SRS Light on a Silverado. Turn the ignition off. Open the hood. Lift up on the tab on the side of the fuse cover to remove it. The fuse block is on the driver’s side of the engine compartment. Pull out the SRS fuse.

Why does the SRS light flash when I Turn on the car?

You will typically see the SRS light on your dashboard. As you turn on your vehicle, the light will flash for a few seconds. However, a problem with the SRS light occurs when it stays on when you are driving. This can be annoying at first, but there could be a much bigger problem going on.

Why does the SRS warning light come on?

SRS light is on. There are a few reasons why the SRS light turns on. One of the most common reasons the airbag light turns on is because there is an interference happening with the seat belt and the sensor. This causes the warning light to falsely come on. The next reason the SRS light might be on has to do with the passenger’s seat.

Why is my Mercedes S430 showing a suspension warning light?

If your Mercedes S430 is showing a suspension warning light, the time to get that car to the shop and fix it was yesterday. Unfortunately, suspension issues are all too common among owners of these vehicles.

Why does my Mercedes S430 sag when coming to a stop?

The first is that the car sits unevenly or too low when parked. Sometimes this will mean one corner of the S430 is lower than others. However, the most common sign is when the rear of the Mercedes is sagging down. When coming to a stop, does your S430 “crouch” forward? If so, it means that at least the front air suspension is worn out.

How often does the slip indicator light blink?

When one of the ESP® systems other than ABS is activated, the SLIP indicator light in the instrument cluster blinks 5 times per second. CAUTION: If the SLIP indicator light comes on and stays on while driving, there may be a malfunction of the ESP® systems (other than ABS). You should have the systems inspected by an authorized SUZUKI dealer.

How does the SRS light work on a car?

When one sensor detects a collision, it will send a signal to your airbag control unit to deploy the airbags. When the airbag control unit gets that information it sends a signal to your airbags, which are mounted in several places in your car. All of this happens in the time of milliseconds.

Can a failed ABS sensor trigger the Bas light?

If you have an ABS sensor that has failed, it will also trigger the ABS, ESP, BAS light. Because the ESP system depends on the ABS system to function properly, the ESP system will also get disabled.

What kind of fuses are in a 1998 SL500?

Electrical components such as lights, heated seats and radios all have fuses in your 1998 Mercedes-Benz SL500 5.0L V8. This free video shows you how to replace a blown interior fuse on a 1998 Mercedes-Benz SL500 5.0L V8 About Us Maintenance Parts & Tools Contact English SpanishFrench Search Home Mercedes-Benz SL500 1998

Where are the fuses in the SL R230?

SL R230 Fuse Box Locations in the engine bay on driver’s side in the engine bay on passenger’s side in the passenger compartment fuses box in the rear trunk

What does the SRS light on a 3000GT mean?

Chances are, if you’ve owned a 3000GT/Stealth for over a year you’ve probably seen this indicator light. What is it, you ask? The Supplemental Restraint System (or SRS) is the system that controls your airbags. Unfortunately, there are MANY things that trigger this annoying light, and making it go away can cause plenty of headaches.

What does SRS stand for in airbag system?

SRS stands for Supplemental Restraint System. In other words, it is a part of your airbag system. Some manufacturers use an airbag light and some use the SRS light. It is the same thing with different names.

What to do if your car has a bad SRS light?

Take your car to a mechanic: Take your vehicle into your local service shop or dealership service center to be seen by a certified mechanic. They can diagnose and resolve the problem, ensuring that your vehicle is safe to drive again.

Why is my anti lock brake light still on?

If you know your car’s anti-lock brake system is in good condition and the light is still on, there are some steps you can take to reset the light. The problem most likely lies in the car’s central computer or ABS sensor, but it can also be from something else in the brake or electrical system.

Why does the SRS light stay on after an accident?

If the car has been in an accident and the air bags went off will the srs light stay on simply because they didn’t reset the system or would it most likely be that the scum dealer I bought this pos from didnt even replace the air bags or anything from the accident…

When does the ABS warning light come on?

Anytime a problem occurs in the ABS brake system the warning light gets on. In fact, ABS light stays on unless you fix the core issue. Basically, the warning light alerts the driver that the safety system is no longer active.

How to get and erase ABS trouble codes?

Our mission is to provide you with information that can help you solve your car problem quickly. How to Get and Erase ABS Trouble Codes! An error occurred while retrieving sharing information. Please try again later.

How much does it cost to fix an ABS light?

The cost to repair ABS system varies based on severity of your problem along with the make, model and year of your car. ABS control modules cost anywhere from $200 up to $600 each, while ABS wheel sensors run from $100 to $200 each. Therefore, how to fix ABS light is actually spending from $100 to over 800$. 5.

What causes an ABS sensor to short out?

Damaged ABS Sensor The ABS wheel sensor monitors the wheel rotation, controlled by its computer. This sensor works as a conjunction with the wheel stator attached to axle brake rotor, bearing hub or CV joint. With time, these sensors may short out as they are subject to vibration or road conditions. 3. Faulty ABS Computer Module

Why does my SRS light keep coming on?

Your SRS Light may indicate a more serious problem that should be evaluated by your local Authorized Honda/Acura Technician. Remember, that airbag may save your life or the life of someone you care about so don’t disregard that indicator light unless you are sure that it triggered for some other reason.

Why is my SRS light not working on my Honda Civic?

I recently had this issue with my 1999 Civic SiR, and it turned out the issue was that the internal contact points of the car horn had corroded. Replacing the car horn, and then resetting the SRS light by disconnecting the battery for about 10 or so minutes fixed things.

Navigation