What does code p1259 mean on a Honda?
As stated elsewhere, code P1259 refers to an electrical issue in the VTEC control system, and all diagnostic procedures for this code should start with a thorough visual inspection of all associated wiring and connectors. Nonetheless, some other common causes of code P1259 could include the following-
Where is the p1259 sensor located on a Honda Civic?
It should be noted though while that code P1259 specifically refers to a problem in the VTEC systems’ control/signal/monitoring circuit, some mechanical failure modes can contribute to this code being set and stored. Where is the P1259 sensor located? The image above shows the location of the VTEC oil control solenoid on a Honda Civic engine.
What is the OBD 2 fault code for Honda?
OBD II fault code P1259 is a manufacturer specific code that is defined by carmaker Honda as “VTEC System Circuit Fault (Bank 1)”, and is set on these applications when the PCM (Powertrain Control Module) detects a defect, malfunction, or failure in the electrical control/monitoring system of the VTEC mechanism on Bank 1.
What is the trouble code for Honda VTEC?
P1259 – VTEC system malfunction (Honda) Trouble Code Fault Location Probable Cause P1259 VTEC system malfunction Wiring, VTEC solenoid/pressure switch, E
What does the p1259 Honda engine code mean?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P1259 HONDA code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
It should be noted though while that code P1259 specifically refers to a problem in the VTEC systems’ control/signal/monitoring circuit, some mechanical failure modes can contribute to this code being set and stored. Where is the P1259 sensor located? The image above shows the location of the VTEC oil control solenoid on a Honda Civic engine.
OBD II fault code P1259 is a manufacturer specific code that is defined by carmaker Honda as “VTEC System Circuit Fault (Bank 1)”, and is set on these applications when the PCM (Powertrain Control Module) detects a defect, malfunction, or failure in the electrical control/monitoring system of the VTEC mechanism on Bank 1.
Where is the VTEC system malfunction code p1259?
Re: VTEC System Malfunction code P1259 has appeared. (… Check your variable valve timing oil pressure switch, it’s located on the passanger side just before the intake manifold, also the solenoid may be dirty or bad. some people say to clean the screen but that requires removing the entire assembly where these two units are… Good luck
As stated elsewhere, code P1259 refers to an electrical issue in the VTEC control system, and all diagnostic procedures for this code should start with a thorough visual inspection of all associated wiring and connectors. Nonetheless, some other common causes of code P1259 could include the following-
Re: VTEC System Malfunction code P1259 has appeared. (… Check your variable valve timing oil pressure switch, it’s located on the passanger side just before the intake manifold, also the solenoid may be dirty or bad. some people say to clean the screen but that requires removing the entire assembly where these two units are… Good luck
How much does it cost to diagnose the p1259 Honda code?
What does this mean? The cost of diagnosing the P1259 HONDA code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P1259 HONDA code detected?
What does OBD 2 fault code p1259 mean?
What Does Code P1259 Mean? OBD II fault code P1259 is a manufacturer specific code that is defined by carmaker Honda as “VTEC System Circuit Fault (Bank 1)”, and is set on these applications when the PCM (Powertrain Control Module) detects a defect, malfunction, or failure in the electrical control/monitoring system of the VTEC mechanism on Bank 1.
What causes a VTEC system error code p1259?
This error code can be caused by multiple of factors, such as: 1 Low oil pressure or low engine oil level 2 Defective VTEC solenoid 3 Open or shorted VTEC harness 4 Poor electrical connections in the VTEC circuit 5 Defective VTEC oil pressure switch More …
Why does my Honda have a trouble code p1259?
Honda assumes you’ve used the correct oil viscosity. If you use a heavier or lighter weight oil, it may change the operation of the VTEC mechanism and result in a P1259 trouble code. The VTEC phasing device contains a filter screen to prevent sludge and particles from damaging the mechanism.
What does a p1259 VTEC malfunction code mean?
A P1259 VTEC malfunction code will set if the computer doesn’t detect the intended result after commanding a change in valve timing. Honda assumes you’ve used the correct oil viscosity. If you use a heavier or lighter weight oil, it may change the operation of the VTEC mechanism and result in a P1259 trouble code.
What does p1259 stand for in immobilizer code?
There are no codes directly related to P1259. Any problem such as abnormal input or system voltages, intermittent faults, or high resistances in any part of the immobilizer control circuit will set code P1259. Below are some examples of definitions of code P1259 that do not relate to the anti-theft system.
What does a p1259 code mean?
Error Code P1259 is defined as VTEC System Malfunction. This error code is a manufacturer-specific trouble code, meaning it does not apply to all vehicles makes. Rather, it applies only to specific vehicle makes, such as Honda, Acura, etc. Specification of the definition, troubleshooting, and repairs still vary from one make and model to another.
What does check engine code p1259 mean?
P1259 is a code for vtec malfunction usually cause by a bad vtec solenoid, vtec pressure sensor, low oil level, bad connection.
What is a civic p1259 check engine code?
In the Honda Civic, P1259 means that there is a malfunction in the VTEC system. It is a manufacturer specific code, which means that it means the same thing for all vehicles manufactured by Honda. The VTEC system is an integral part of your Civic’s engine It stands for Variable Valve Timing and Lift Electronic Control System.
What does p1259 failure mean?
Code P1259 is for a VTEC system failure. This is usually caused by low engine oil…….the VTEC system runs off oil pressure and if the oil is low this code will set.