What does code p0720 mean on Transmission Control Module?
What Does Code P0720 Mean? The TCM (transmission control module) or PCM (powertrain control module) has received an input signal from the transmission OSS (output speed sensor) or VSS (Vehicle speed sensor) that is erratic.
What causes the p0720 Ford output shaft sensor to malfunction?
P0720 FORD Possible Causes 1 Faulty Output Speed Sensor (OSS) 2 Output Speed Sensor harness is open or shorted 3 Output Speed Sensor circuit poor electrical connection 4 Faulty Powertrain Control Module (PCM) More …
Where is the p0720 sensor located on a PCM?
You’ll commonly see this sensor mounted near the output shaft on the transmission. The P0720 code is activated when the PCM detects insufficient input from the OSS. This code is similar to P0721, P0722, and P0723.
How much does it cost to fix a p0720 code?
The cost of diagnosing the P0720 code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0720 code detected?
What is OBDII trouble code p0720?
What the P0720 code means. The P0720 code is a standard OBD-II trouble code that detects an issue with the output speed sensor circuit. The powertrain control module (PCM) relies on a signal from the output speed sensor, so that it can determine the correct shift strategy and send that information to the transmission.
What does p0720 mean on your Dodge OBD?
P0720 is a generic OBD II trouble code, which means that it has the same meaning for your Dodge Dakota as it would any other vehicle. It indicates that your Dakota’s OSS (Output Shaft Speed Sensor) is reporting a malfunction. It’s typically caused by a bad OSS, or a wiring problem.
What would cause a p0720 code?
There are a handful of different issues that can result in the P0720 code, including: Malfunctioning output speed sensor. Malfunctioning input speed sensor. Damaged or corroded wires, or loose connectors. Contaminated or low transmission fluid. Faulty engine drivability sensors. Malfunctioning shift solenoids.
What is a transmission output sensor?
Transmission Output Speed Sensor . An output speed sensor of a car, truck, or SUV measures the rotational speed of the output shaft in RPMs. This is not the same as the measurement of the vehicle speed, which is measured by the vehicle speed sensor, or by the wheel speed sensors.
How to diagnose p0720 output shaft speed sensor malfunction?
Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded terminals. The cost of diagnosing the P0720 code is 1.0 hour of labor.
When does the output shaft speed sensor malfunction?
If no signal from the Output Shaft (Countershaft) Speed Sensor is received for a set period of time, the ECM detects a malfunction, and a Diagnostic Trouble Code (DTC) is stored. Need more information on how to fix the P0720 HONDA code?
What should I do if my Ford F250 has p0720?
You should notice symptoms when your F250 has P0720. Since the code is transmission related, your engine should run fine. The concern will be how the transmission behaves without the signal from the OSS. In very rare cases the vehicle may misfire or even die when stopping.
P0720 FORD Possible Causes 1 Faulty Output Speed Sensor (OSS) 2 Output Speed Sensor harness is open or shorted 3 Output Speed Sensor circuit poor electrical connection 4 Faulty Powertrain Control Module (PCM) More
What does p0720 mean on a car computer?
Your car computer may display Code P0720 if it detects a problem with the output speed sensor. What Does the P0720 Code Mean? Diagnostic trouble code (DTC) P0720 stands for “Output Speed Sensor Circuit Malfunction.”
You’ll commonly see this sensor mounted near the output shaft on the transmission. The P0720 code is activated when the PCM detects insufficient input from the OSS. This code is similar to P0721, P0722, and P0723.
How much does it cost to diagnose Ford p0720 code?
The cost to diagnose the P0720 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
What Does Code P0720 Mean? The TCM (transmission control module) or PCM (powertrain control module) has received an input signal from the transmission OSS (output speed sensor) or VSS (Vehicle speed sensor) that is erratic.
Why is the speed sensor not working on my Ford p0720?
OBD2 CAN bus reader scanned P0720 for transmission output shaft speed sensor circuit failure. The check engine light was illuminated, the speedometer was not working and upshifts were slow and sluggish. The green overdrive off light was flashing.The OSS measures driveshaft rotations for spedo and odometer. Shaft RPM also controls shifting.
The cost of diagnosing the P0720 code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0720 code detected?
How to diagnose a p0720 output shaft malfunction?
Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded terminals. The cost of diagnosing the P0720 code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type.