What are the P codes for bank 2?
P0018 Crankshaft position/camshaft position, bank 2 sensor A -correlation Wiring, CKP sensor, CMP sensor, mechanical fault P0019 Crankshaft position/camshaft position, bank 2 sensor B -correlation Wiring, CKP sensor, CMP sensor, mechanical fault
What are the P codes for mechanical fault?
P0016 Crankshaft position/camshaft position, bank 1 sensor A -correlation Wiring, CKP sensor, CMP sensor, mechanical fault P0017 Crankshaft position/camshaft position, bank 1 sensor B -correlation Wiring, CKP sensor, CMP sensor, mechanical fault
What are the P codes for an engine?
P0012 Camshaft position (CMP), intake/left/front, bank 1 timing over -retarded Valve timing, engine mechanical fault, CMP actuator P0013 Camshaft position (CMP) actuator, exhaust/right/rear, bank 1 -circuit malfunction Wiring, CMP actuator, ECM
What are the P codes for fuel metering?
P0XXX Codes Trouble Code Fault Location Probable Cause P0000 – P0099 (Fuel and air metering and auxiliary emission control) P0000 No fault P0001 Fuel volume regulator control -circuit open Wiring, regulator control solenoid P0002 Fuel volume regulator control -circuit range/performance Wiring, regulator control solenoid
What are the symptoms of a p2a00 code?
Symptoms of a P2A00 code may include: 1 Diminished fuel efficiency 2 A lack of general engine performance 3 Other related diagnostic trouble codes may also be stored 4 Service engine soon lamp illumination
What to do if your p2a00 sensor is intermittent?
Proceed by retrieving all stored trouble codes and freeze frame data by connecting the scanner to the vehicle diagnostic port. This information may be helpful if the P2A00 proves to be intermittent, so write it down. Clear the codes and test drive the vehicle to see if the P2A00 is immediately reset.
What does it mean when a Land Rover has a p2a00 code?
In my experience, when an OBD-II equipped vehicle has stored a P2A00 code, it means that the powertrain control module (PCM) has detected a malfunction in the upstream (or pre catalytic converter) oxygen (O2) sensor or circuit.
What does the sensor code p0641 stand for?
The sensor in question is typically associated with the automatic transmission, transfer case, or one of the differentials. This code will almost always be accompanied by a more specific sensor code. The P0641 adds that the circuit is open.
What does Bank 1 Bank 1 p0011 stand for?
P0011 – Intake Camshaft Position Timing – Over-Advanced (Bank 1) Description: The powertrain control module (PCM) monitors the variable camshaft timing (VCT) position for an over-advanced camshaft timing. The test fails when the camshaft timing exceeds a maximum calibrated value or remains in an advanced position. Possible Causes:
What does p0016 stand for in Powertrain Control Module?
P0016 – Crankshaft Position – Camshaft Position Correlation – Bank 1 Sensor A Description: The powertrain control module (PCM) monitors the variable camshaft timing (VCT) position for a misalignment between the camshaft and crankshaft. The test fails when the misalignment is greater than 1 tooth. Possible Causes:
What is the OBD 2 fault code p0107?
OBD II fault code P0107 is defined as “ Manifold Air Pressure/Barometric Pressure Circuit Low Input”, and is set when the PCM (Powertrain Control Module) detects a signal from the MAP (Manifold Air Pressure Sensor) that falls outside of the expected value for the reigning engine load or throttle position,…
What does the code p0107 on a Tahoe mean?
2008 Chevy Tahoe code P0107. Multi codes + multi abnormalities My chevy tahoe 5.8 4WD Indicating: – TPS light – Check Engine light – TC light – Stabilitrak light Also, cylinders 1 & 4 misfire, error code P0107 refers to MAP low voltage The car vibrates, gas smell when started, exhaust smoke when sharply accelerating.
What does lean fault code p0171 mean on a car?
Your car or truck has either a P0171, P0174 lean fault code or both stored in the pc, these codes derive from Oxygen Sensor (O-2) readings. A lean code or codes suggest that there surely is too-much air in the exhaust.
What causes a p0107 DTC to be set?
A P0107 DTC is set when the PCM sees that the MAP signal voltage is less than .25 volts which is too low. Anytime the MAP sensor signal is low the vehicle will likely have a very difficult time starting. Other symptoms may include: MIL (Malfunction Indicator Lamp) illumination