What are the OBD procedures for a Jaguar?

Welcome to the Jaguar onboard diagnostics OBD-II drive cycle information page. The procedures detailed below apply to many but not all 1996-newer Jaguar models. The steps should generally be the same but refer to an authorized Jaguar repair/service guide or possibly owners manual to confirm steps for your Jag.

What are the trouble codes for a Jaguar?

So to be 100% accurate you’ll need to refer to a service repair manual specific to your year/model/engine configuration such as Jaguar Technical Information System (JTIS) or possibly AllDataDIY. Other Jaguar-specific content on our site: Trouble codes that start with P0, P2, P34, B0, C0, U0, or U3 are all considered “generic”.

What is the Mil code on a Jaguar X350?

Jaguar X350 ECU1 ($FD20) ECU1 (FD00) Codes? Hi all and good afternoon from a cold and windy Northumberland. The MIL has suddenly started appearing on my 2005 X350. I plugged the iCarsoft in and on the Jaguar specific search it came back with “Fault in communication with vehicle ECU”.

What should the engine temperature be in a Jaguar OBD-2?

Oxygen sensor heaters: Start engine and bring to normal operating temperature > 82 °C (180 °F). Idle engine for 3 minutes. Start engine and bring to normal operating temperature > 82 °C (180 °F). Idle for a minimum of 10 minutes.

What kind of Diagnostic monitor does a jaguar have?

The diagnostic monitors for your Jaguar may include: Heated Oxygen Sensors Monitor Adaptive Fuel Monitor Misfire Monitor Catalyst Efficiency Monitor Evaporative System Monitor Exhaust Gas Recirculation Monitor Drive Cycle Comprehensive Component Monitor (Engine Management / Transmission)

When do you turn off the oxygen sensors on a Jaguar?

Upstream (Universal) oxygen sensors: Engine OFF; cooling fans inoperative > 20 seconds. Start engine and bring to normal operating temperature > 82 °C (180 °F). Drive the vehicle between 3000 – 4000 rpm at a steady speed. Lift foot completely off accelerator and coast to a stop within 30 seconds.

When to deactivate the check engine Mil in a Jaguar?

If on the first trip, the misfire is severe enough to cause catalyst damage (more severe than excess exhaust emission), the CHECK ENGINE MIL will flash while the fault is present and the individual cylinder DTC plus DTC P1313 (bank 1), DTC P1314 (bank 2) will be logged. When the fault is no longer present the MIL will be deactivated.

What are the drive cycle procedures for a Jaguar?

Using WDS, check for and clear flagged DTCs. Start engine and bring to normal operating temperature > 82 °C (180 °F). Drive the vehicle in 3rd gear at 2500 rpm. Maintain a steady speed for 1 minute, then lift foot completely off accelerator and coast for a minimum of 10 seconds. We do not have the procedures at this time.

How many points of Inspection does a Jaguar need?

There is a checklist of 165 points of inspection in place that has to be followed to the letter. This ensures your vehicle is in optimum electrical and mechanical condition. Using the very latest technologies, tools and diagnostic equipment, Jaguar technicians carry out these checks with the utmost rigor.

What does it take to become a Jaguar pre owned vehicle?

The inspection always includes paintwork, interior, a complete engine preparation, road test and a final inspection before the vehicle is personally signed off by a Jaguar Technician. All vehicles have to pass all 165 checks to become a Jaguar Approved Certified Pre-Owned vehicle.

What kind of warranty does a certified Jaguar have?

Each Certified Pre-Owned Jaguar vehicle is backed by an up to 7-year/100,000-mile limited warranty* — in what was recently named IntelliChoice’s Best Premium CPO Program. Find your next Jaguar vehicle today.

How does the EVAP system work in a Jaguar?

Drive vehicle to the road where the EVAP System Drive Cycle will be conducted. Stop vehicle and switch OFF the ignition. Leave ignition OFF for 30 seconds, then restart the engine. Accelerate briskly to 80 km/h (50 mph) ensuring that the engine speed reaches a minimum of 3500 rpm for a minimum of 5 seconds.

How to run an oxygen sensor in a Jaguar?

Downstream oxygen sensors: Start engine and bring to normal operating temperature > 82 °C (180 °F). Drive the vehicle steadily between 48 – 97 km/h (30 – 60 mph) for 10 minutes. Drive the vehicle above 3000 rpm in 4th gear at a steady speed. Lift foot completely off accelerator and coast for 30 seconds. Oxygen sensor heaters:

Where is the OBD2 port on Jaguar XK?

Where is the OBD2 port on Jaguar XK (1996 – 2015) ? Mode X column: A vehicle showing 00000000 on a mode means that no corresponding PID is active and that as a result the mode is supported but will not reply to any requests. None of the vehicles described below support mode 8.

What is the diagnostic code for a Jaguar check engine light?

Refer to our Generic OBD II code list for definitions on all other Jaguar diagnostic trouble codes. Manufacturer Specific Codes P1000OBD Systems Readiness Test Not Complete P1104Mass Air Flow Sensor Circuit Ground – Read Our Article On Automotive Circuit TestingFor Help With This Jaguar Check Engine Light Code P1111System Pass

Navigation