What are the fault codes for Suzuki motorcycles?
The CKP sensor wiring and mechanical parts. (CKP sensor, wiring/coupler connection) c13 Intake air pressure sensor malfunction The sensor produces following voltage. (0.5 V < or = sensor voltage < 4.85 V) Without the above range, c13 is indicated.
Why is my throttle position sensor not working?
The reason this happens is that the ECM doesn’t get correct information from the TPS as to how much to throttle the car. Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS.
How much does it cost to replace a throttle position sensor?
If you need to have your throttle position sensor replaced, the cost will depend on the type of car you have. But the average cost of this replacement job isn’t that expensive. The parts will cost you between $75 and $130 on average. The labor costs will be anywhere between $60 and $90, depending on the hourly rate of the mechanics.
Can a bad check engine light be a bad TPS?
The check engine light will randomly turn on and off even if the car is running smoothly without any jerks and stalling. This is often the first ever symptom of a bad TPS. Using a code reader, you should be able to confirm whether a faulty TPS is the culprit or a different component.
What causes a bad throttle position sensor to malfunction?
In short, incorrect amounts of air and fuel means problems for the engine. While the throttle position sensor makes sure the engine gets the correct amount of air, it is common for it to malfunction. Learn bad throttle position sensor symptoms now so that you can take care of this engine problem as soon as it arises.
How often should a throttle position sensor be replaced?
They are built into the sensor so they can not be replaced like those of a flashlight. Hence, it is recommended by car manufacturers to replace TPS sensors every 5 years to enjoy safe and hassle-free driving. Do not leave it until you’re encountering faulty throttle position sensor symptoms.
What happens when the throttle gets stuck in an open position?
When the throttle gets stuck in an open position than your vehicle will receive too much air and cause it to have a high or fluctuating idle. What are signs of a bad Throttle Position Sensor? Acceleration issues: A bad TPS may cause all sorts of power issues. Your engine may start up but it will have little to no power and it causes it to shut off.
Can a bad TPS cause an engine to shut off?
Acceleration issues: A bad TPS may cause all sorts of power issues. Your engine may start up but it will have little to no power and it causes it to shut off. Unstable Engine Idle: Faulty position sensors can cause sporadic idle conditions due to fluctuating airflow.
What does c00 mean on a Hayabusa diagnostic plug?
If you have the jumper wire making a good connection between the red/white and black/white wires/pins of the white diagnostic plug, then you should see “C” and a 2 digit number where it says “CHEC”. C00 means no codes are present. The code will only be present when the FI light is on. The ecu does not/cannot store codes.
What is the fault code for the GSXR ECU?
TP sensor, wiring/coupler connection. The sensor voltage should be the following. (0.15 V < or = sensor voltage < 4.85 V) Without the above range, c15 is indicated. ECT sensor, wiring/coupler connection. The sensor voltage should be the following. (0.15 V < or = sensor voltage < 4.85 V) Without the above range, c21 is indicated.
What is the fault code for the IAP sensor?
IAP sensor, wiring/coupler connection. The sensor produces following voltage. (0.2 V < or = sensor voltage < 4.8 V) Without the above range, c14 is indicated. TP sensor, wiring/coupler connection. The sensor voltage should be the following. (0.15 V < or = sensor voltage < 4.85 V) Without the above range, c15 is indicated.
If you have the jumper wire making a good connection between the red/white and black/white wires/pins of the white diagnostic plug, then you should see “C” and a 2 digit number where it says “CHEC”. C00 means no codes are present. The code will only be present when the FI light is on. The ecu does not/cannot store codes.
The CKP sensor wiring and mechanical parts. (CKP sensor, wiring/coupler connection) c13 Intake air pressure sensor malfunction The sensor produces following voltage. (0.5 V < or = sensor voltage < 4.85 V) Without the above range, c13 is indicated.
What is the F1 code on a Suzuki GSXR?
It is is small white connector that does not plug into anything, and has a rubber cap on one end. Click to expand… This is weird, after riding my 2002 GSXR-1000 over 19,000 miles I get the F1 code C46.
Why does my Suzuki GSXR have a Fi warning?
Originally when the full exhaust Yosh RS-3 was installed all was done was the black/brown wire from the ECU input will prevent that “Fi” warning message from appearing in your instrument panel. That was the only wire cut, that’s it.