Is there a recall on my Turn signal?
FOR EVERYBODY SUFFERING FROM THE FAULTY TURN SIGNALS (SOMETIMES THEY WORK, SOMETIMES HEY DONT) THERE WAS A RECALL NOTICE SENT THROUGH THE MAIL STATING THAT THERE IS A FACTORY DEFECT IN THE WIRING SYSTEM OF THE TURN/HAZARD LIGHTS …
Why does my CLS 320cdi have no power loss?
Now there is no Engine management light on I have power loss (no turbo) and irrespective of how far I press down the accelerator and doesnt rev more than 30 rpm when in N / P but No warning light. Once you stop, turn the engine off for a little while and restart the problem goes away but comes back after car has warmed up some time later.
What’s the problem with Mercedes Benz check engine light?
Then when taken to another dealership the “problem” is diagnosed as another sensor or valve and once again we have been charged up to $2000. Mercedes Benz diagnoses of the check engine light are unreliable and many times we have been charged for repairs that do not resolve the problem.
Why is the NoX sensor on my Mercedes not working?
I thought that if you clear the code the car’s computer would determine if the NOx sensor is working properly… or not. Most of these problems are related to Mercedes and Bosch causing it to begin with. Mercedes and Bosch are going to lose more the a few billion dollars.
Why is my turn signal not working on my Mercedes?
1) Remove the console top cover and unplug the 8-pin plug from the emerg. switch. 2) Take a loop of wire and short out contacts 49 and 30 (next to each other) on the plug. Your indicators should now work normally. If not, then the problem lies either with the flasher unit (expensive) or the ind. switch on the column.
What to do if your turn signal stops working?
Check the emergency flasher switch on the center console. If that is between on and off or is broken it will cause your turn signals to act up. If the switch seems ok then unplug it and try the turn signals. The emergency switch is easily broken in that location (you’ll note the 124 chasis has the switch moved up to the top of the console.)
Do you need to replace the turn signal switch?
Take a look at the part inside the turn signal/combination switch that often fails. You can’t replace the internal part, therefore, the whole turn signal switch needs to be replaced. Click here to check prices on new & used Mercedes turn signal switches. Replace the turn signal switch.
Where is the turn signal switch on a Honda Accord?
The turn signal switch is part of the combination switch found in the steering column and is mounted right behind the steering wheel. You may also notice that the wiper switch is not working either. That’s because the turn signal switch and wiper switch are combined in one.
What kind of engine does a Pontiac Grand Am have?
My car is a 2004 Pontiac Grand AM with the 3.4 v6 engine/auto trans. It is throwing a po122 code which is throttle position sensor. I have changed that and still get the code.
What was the problem with my 2003 Pontiac Grand Am?
2003 Pontiac Grand Am.. I had the same issue, blinker going crazy when I pushed the blinker arm, until eventually the blinker light went out. Not the bulbs, got an entire new rear light box from a selvage yard and then installed. That was 2 years ago. Now, same problem.
FOR EVERYBODY SUFFERING FROM THE FAULTY TURN SIGNALS (SOMETIMES THEY WORK, SOMETIMES HEY DONT) THERE WAS A RECALL NOTICE SENT THROUGH THE MAIL STATING THAT THERE IS A FACTORY DEFECT IN THE WIRING SYSTEM OF THE TURN/HAZARD LIGHTS
My car is a 2004 Pontiac Grand AM with the 3.4 v6 engine/auto trans. It is throwing a po122 code which is throttle position sensor. I have changed that and still get the code.
2003 Pontiac Grand Am.. I had the same issue, blinker going crazy when I pushed the blinker arm, until eventually the blinker light went out. Not the bulbs, got an entire new rear light box from a selvage yard and then installed. That was 2 years ago. Now, same problem.