Is there a problem with my Chevy Malibu?
God Bless Berger for his post!!! http://www.bergerweb.net/AleroSecurity/ 161 people found this helpful. This stinks because my car is doing this again and they have no record of a problem with the Malibu. They just don’t want to fix all our cars. They suck 28 people found this helpful. I am suffering the same problem.
What to do if anti theft light goes off?
Once ten minutes has passed come back and check the anti-theft light. If it has gone off, then turn the key back to the off position and remove the key. Wait for a couple of minutes to make sure that the system reset is finished. Then put the key back in and try to start the car.
Can a Chevy Malibu work in a sand rail?
I HAVE BEED TRYING TO BYPASS THE THIEF SYSTEM FOR A TIME. SO THE ENGINE AND TRANY WILL WORK IN A SAND RAIL AND NO LUCK. IM THINKING THAT NOW IT IS JUST BEST TO JUNK CHEVY’S AND STAY WITH FORD AND DODGE FOR TOY AND HOT RODS.
Bummer to read of the problem with your car. I am not sure what year Malibu you own as you have ignored the forum rules, but assuming 2013, sometimes repairs will be necessary on a 7 year old secondhand car. If that is hard to accept, a trade for a preferred vehicle is a great option.
What are the p0axx hybrid diagnostic trouble codes?
P0AA5 Hybrid Battery Negative Contactor Circuit Stuck Open P0AA6 Hybrid Battery Voltage System Isolation Fault P0AA7 Hybrid Battery Voltage Isolation Sensor Circuit P0AA8 Hybrid Battery Voltage Isolation Sensor Circuit Range/Performance P0AA9 Hybrid Battery Voltage Isolation Sensor Circuit Low
How to get diagnostic code for Toyota check engine light?
1 Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2 Turn the ignition on. 3 Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s).
Where do I find the trouble code on my Chevy?
These are listed in numerical order for easy searching. When retrieving Chevy trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.
What does DTC p0abd stand for on Malibu Eco?
Verify DTC P0ABB, P0ABC, or P0ABD is not set. ◊ If any of the DTCs are set Note: In High Voltage Disabling See: High Voltage System Disable / Enable, Hybrid > Procedures > High Voltage Disabling , perform the disabling procedure for servicing components within the A4 Hybrid/EV Battery Pack.
How to disable battery on Malibu Hybrid Eco?
The C4A Hybrid/EV Battery Section 1 and C4B Hybrid/EV Battery Section 2 will be disconnected as part of the disabling procedure. 1. Ignition OFF, disable high voltage at the A4 Hybrid/EV Battery Pack. Refer to High Voltage Disabling See: High Voltage System Disable / Enable, Hybrid > Procedures > High Voltage Disabling. 2.
What’s the fault code on my Malibu Hybrid?
Hi i have a malibu 2013 hybrid eco and tha battery light is on and the fault code is P0ABC Mechanic’s Assistant: Let’s get those codes to the mechanic so you two can figure this issue out ASAP. How many miles are on the car?
Is the battery light on on my Malibu?
I have a malibu 2013 hybrid eco and tha battery light is on… Hi i have a… Hi i have a malibu 2013 hybrid eco and tha battery light is on and the fault code is P0ABC Mechanic’s Assistant: Let’s get those codes to the mechanic so you two can figure this issue out ASAP.