How to replace the door lock actuator on a Mercedes Benz?

The first step in replacing the door lock actuator is to disconnect the battery. Remove the small plastic plate at the bottom of the rear passenger seat. Underneath is a 11mm nut holding the negative terminal from the battery to ground. Remove the nut and pull the cable off.

How to replace the lock actuator on a Mini Cooper?

Take off the cable from the door panel clips in order to put the cable into the door panel. Push the cable through the door panel hole, which was blocked by the rubber before. In order to remove the lock actuator with ease, the guide rail for the window nearest the actuator must be moved.

How does the front passenger door lock work?

Unlike the other three doors which has only two cable connections to the door lock actuator mechanism (one for the external door handle and one for the internal door handle and lock) the passenger side front has a third for the keyed door lock.

Where can I get Honda Odyssey door lock actuator?

Please narrow the Power Door Lock Actuator results by selecting the vehicle. A Honda Odyssey needs to be kept in good working condition in your vehicle. The online catalog we provide will get you through the ordering process safely and securely. All genuine Honda Door Lock Actuators from us are shipped directly from authorized Honda Dealer.

What is the purpose of door lock actuator?

A door lock actuator is responsible for locking and unlocking your doors. When the door lock switch is triggered, the actuator’s motor powers a set of gears that lock or unlock your door. When the actuator stops working, there is no communication between the door lock switch and the door locks, and you’ll be unable to lock or unlock the door.

What is a rear door actuator?

In an automotive context, a rear door actuator is a component that is used to lock and unlock a rear liftgate, hatchback, or other similar door. This term can also refer to actuators found in rear side doors, though those are more commonly called left rear or right rear door actuators.

What is an electric door lock actuator?

A door lock actuator is the component in electronic door locks that is responsible for locking and unlocking the vehicle’s doors.

How do you unlock a car door with an actuator?

There are a number of ways that you can unlock car doors that have door lock actuators, including: Using a key Pressing the unlock button inside the car Using the combination lock on the outside of the door Pulling up the knob on the inside of the door Using a keyless entry remote control Signaling from a control center

Why is my Mercedes ML320 door lock not working?

The Problem: The actuators for the individual doors get damaged and jammed thus not responding to the motor when it tries to lock or unlcok the door. When using the keyfob or the dash button for locking or unlocking the doors, the jammed door actuator tries times to complete the lock/unlock action.

Can a faulty door lock actuator be repaired?

The power door lock actuator can be integral to a car door lock repair. If a remote device or unlock switch fails, the actuator may be faulty. Car door lock actuators are designed to lock and unlock a door without the effort of pulling on a cable and rod.

How to replace the actuator on a Mercedes W210?

The first step in replacing the actuator is to disconnect the battery. Remove the small plastic plate at the bottom of the rear passenger seat. Underneath is a 11mm nut holding the negative terminal from the battery to ground. Remove the nut and pull the cable off. Remove the screw holding the door latch cover in place.

Why does my Mercedes Benz door not lock?

Unfortunately, as the cars age, the components of the vacuum system can deteriorate, eventually leading to leaks that will typically prevent one door from locking while the others lock with no problem.

How to replace door lock on Mercedes W210?

Remove the hook on the end of the inner door handle cable from the old door lock actuator. Pull the gasket out of the channel on the rear of the door. You want to find the small access hole inside the channel. This will allow you to access the small 4mm Allen bolt that retains the IR sensor/Door handle (green arrow).

Why is my driver’s side door lock not working?

Thanks to the good people here at Benzworld.org I was able to fix my driver’s side door lock without involving my mechanic or having to buy parts. This seems to be a huge issue with W202’s and something that many of you will also deal with. My driver’s side door lock stopped working.

How do you remove the door handle on a Mercedes C class?

Once done, remove the handle’s blanking plate and unscrew the T20 Torx that holds the outer door handle. Now, in order to remove the handle, first remove small part of the handle release by removing the previous T20 Torx. Next, slide handle to the left to release from vehicle.

How to replace the lock on a Mercedes C class?

Remove the T20 Torx and remove lock cover. Take care when levering off the cover from the door handle; you may need to shimmy it back and forth a bit. Now, remove the two Torx bolts under the handle cover. Figure 1. Lock mechanism mounting screws.

What kind of front latch does a Mercedes Benz have?

Current: 2003 SL55 Obsidian Black, 2007 ML500 Silver. Former: SL500, 560SEL, 450SEL, 300SEL 6.3 The lines are permanently attached to the cylinder and as Peter mentioned, you would have to trace it back to the pump, which is in the bottom left side of the trunk.

What kind of door lock does the Mercedes W210 use?

The W210 Mercedes was one of the last cars produced that still used the older, proven vacuum system before finally converting to electrically operated door locks.

When did Mercedes Benz start using vacuum operated locks?

Nowadays, electronics are nearly foolproof and are cheap enough to use in almost any application. Mercedes started using vacuum operated locks sometime in the 1970’s, when modern electronics were still expensive and not quite reliable enough to be used in a system that would be used so frequently.

How do you remove a door lock relay?

Step 1: Find the door lock relay. Go to the breaker panel on the wall next to the brake pedal. Using a diagram, locate the door lock relay. Step 2: Remove the old door lock relay. With a pair of needle nose pliers, pull out the relay.

What are the symptoms of a bad door lock relay?

Usually a bad or failing door lock relay will produce a few symptoms that can alert the driver of a potential problem that should be serviced. One of the first symptoms of a possible problem with the door lock relay are door locks that function intermittently.

What causes a door lock to stop working?

If the door lock relay has any internal or wiring issues, it can cause the door locks to function intermittently. The door locks may function correctly one moment, and in the next will cease to operate.

How to repair a door lock actuator step by step?

Part 4 of 6: Repairing the door lock actuator Step 1: Use a razor blade to open up the actuator.. Start on the corner by slicing your razor through the seam. Warning:… Step 2: Remove the electric motor from the actuator.. Pry up on the gear and pull it out. Then pry the motor up from its… Step …

How to replace lock actuator on Ford F250?

Lift the door panel up and off. Pry up the rubber plug in the side of the door. Unplug the courtesy light. Peel back the water shield. Roll your window all the way up. Remove the 10 mm bolt on the lock actuator. Disconnect the lock rod from the actuator. Remove the two 11 mm nuts with a socket and extension securing the handle.

What to do if your door lock actuator is broken?

If you pull up or push down on the lock post and it doesn’t “click” into the locked or click into the unlocked position, then the spring is broken. If your actuator makes the rapid up and down movement displayed in the video, then more than likely the actuator is OK and you just need to replace the spring.

How do you remove a car door holder?

Unbolt the door holder from the body of the car. Note: In some vehicles the door holder is an integrated piece on one or both of the door hinges. If you find this is the case, skip to the next step. Unbolt the hinges. Unbolt the hinges from the door. Remove the door. With the bolts removed, the door should basically fall away from the car body.

How can I adjust the fit of my car door?

Adjust door fit: Hinge bolts are the only way to adjust the door fit without serious body work. Loosen the door hinge bolts slightly, just enough to shift the door, try to move the door in the hinge bolt holes. (Not every car will be able to move the door within the bolt holes.

How do you reset adaptive shifting on a Mercedes Benz?

This procedure will reset the adaptive shifting points in your Mercedes-Benz automatic Transmission Control Unit (TCU). These simple do it yourself instructions take less than 5 minutes. No tools are required to perform this procedure and make your Mercedes-Benz shift like new.

How long does it take to shift a Mercedes Benz?

These simple do it yourself instructions take less than 5 minutes. No tools are required to perform this procedure and make your Mercedes-Benz shift like new. Try this if your car has been shifting sluggish recently. This will make your car fun to drive again, it’s like getting a free tune-up.

Where is the IR sensor on a Mercedes W210?

Pull the gasket out of the channel on the rear of the door. You want to find the small access hole inside the channel. This will allow you to access the small 4mm Allen bolt that retains the IR sensor/Door handle (green arrow). Carefully loosen the bolt until you can remove the IR sensor on the door handle.

Navigation