How to clean the Kia throttle body cleaner?
Tech Tip: Kia Throttle Body Cleaning 1 Remove the breather hose (A) and the air intake hose (B), to gain access to the ETC assembly ( see Fig. 2 ). 2 Disconnect the ETC connector (C) ( see Fig. 3 ). 3 Remove the four ETC mounting bolts as indicated and the ETC from the intake manifold ( see Fig.
Why does my Kia Theta engine not start?
Some Kia drivers may complain of an engine that is hard to start, or that won’t start at all. DTCs P2110, P2118 or P2119 (throttle valve stuck closed) may be present on Theta 2.0L/2.4L engine-equipped vehicles. The condition may occur from carbon deposits and/or fuel additives accumulated in the throttle body.
Is there a way to reset the throttle body?
This method is almost foolproof as long as all ECU control parameters are within their normal ranges. Resetting The Throttle Body Calibration (this step is conditional) A Rough Idle or a SES can sometimes be caused by a change in the throttle body position sensor calibration.
How do you change the throttle on a Kia Sorento?
Remove the screws securing the TPS using a Phillips screwdriver and pull the TPS from the throttle body. Install the new TPS onto the throttle body so its tabs insert into the slots on the throttle body valve. Tighten the TPS screws just until snug with a Phillips screwdriver. Plug the wiring harness into the TPS.
When to reset adaptive value on Kia throttle?
If the MIL is illuminated with DTC P0638 or P2110, follow this procedure to reset/relearn the adaptive value before replacing the ETC system or any related components.
How do you learn the throttle on a Kia?
If the vehicle is equipped with a push button start system, push the engine start button two times without depressing the brake pedal. This will allow the ECM to automatically learn the throttle valve position. Then wait for approximately five seconds.
What to do if your Kia throttle position sensor is not working?
Thereafter, take out the three bolts attached to the throttle body to disconnect it from the intake manifold. Finally, have the throttle body gasket removed and cleaned. If you face a problem with your Kia throttle position sensor, troubleshooting the component would be strongly recommended before starting to repair the issue.
If the MIL is illuminated with DTC P0638 or P2110, follow this procedure to reset/relearn the adaptive value before replacing the ETC system or any related components.
What can cause a 2004 Kia Amanti to have the code p1110?
What can cause a 2004 Kia Amanti to have the codes P1110, P1175 and P1196? A faulty electronic throttle system, a defective throttle blade, a bad throttle body or a failed throttle position sensor can cause this to happen. The best recourse would be to troubleshoot each of these possibilities and find out what is causing the problem.
What can cause a 2005 Kia Sorento to cut off on idle?
What can cause a 2005 Kia Sorento to cut off on idle despite replacing the throttle position sensor? A gummed up idle air control valve or a defective ignition switch can cause this problem. The best course of action would be to contact an Expert and have them troubleshoot to resolve the issue.
How do you change the throttle position on a Kia?
Then, unfasten the clamp and remove the air intake hose from the throttle body. Then, unplug the idle air control (IAC) valve connector and take out the screws of the accelerator cable bracket.
Can a faulty throttle position sensor cause a Kia Sportage?
Could a faulty throttle position sensor cause a Kia Sportage to frequently downshift and cease to operate on stopping? A faulty throttle position sensor could likely cause the issue described. However, in some situations, it could also occur from low line pressure in the transaxle or an engaged converter clutch.
What should I do if my fuse blows on my Kia?
If the replacement fuse blows, this indicates an electrical problem. Avoid using the system involved and immediately consult an authorized KIA dealer. Three kinds of fuses are used: blade type for lower amperage rating, cartridge type, and multi fuse for higher amperage ratings. same rating.
What causes a Kia to back off the throttle?
As the car moves off at some point it will elect to change into 2nd. This will happen ad quite low speed if using light accelerator pressure (about 5 or 6 mph IMO). To shift up the ECU will back off the throttle before switching clutches.
How do you replace a fuse on a Kia Sorento?
1. Turn the ignition switch and all other switches off. 2. Remove the fuse panel cover by pressing the tab and pulling the cover up. 3. Check the removed fuse; replace it if it is blown. To remove or insert the fuse, use the fuse puller in the engine compartment fuse panel.
As the car moves off at some point it will elect to change into 2nd. This will happen ad quite low speed if using light accelerator pressure (about 5 or 6 mph IMO). To shift up the ECU will back off the throttle before switching clutches.
Some Kia drivers may complain of an engine that is hard to start, or that won’t start at all. DTCs P2110, P2118 or P2119 (throttle valve stuck closed) may be present on Theta 2.0L/2.4L engine-equipped vehicles. The condition may occur from carbon deposits and/or fuel additives accumulated in the throttle body.