How to change the brake light on a Jeep Liberty?
Brake light replacement. Needed: Sylvania 3157 bulb, 10mm socket, T-20 star bit. Wrench. I used a power wrench but a manual socket wrench works fine too. Takes 5 minutes. Same process works for changing amber light or tail light. This is a 2011 Jeep Liberty but the process is the same for 2008, 2009, 2010, 2011, and 2012 Jeep Liberty. Loading…
What kind of light bulb do I need for my Jeep?
Knowing your Jeep headlight bulb size makes it easy to change. Find the Jeep headlight bulb size you need for your low beam or high beam. Also, find your Jeep fog light bulb, reverse light bulb, turn signal bulb, brake light bulb and more.
Why is my brake light bulb not working?
Many cars feature a bulb that includes both a brake light and a tail light filament. This means that even if your brake light is on your tail light might not be working, or the opposite may be true. Brake light bulbs wear out over time, and if only one brake light comes on, the other should be replaced.
What are the warning lights on a jeep?
The following are warning lights and indicators found in vehicles built by Jeep. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are nearly 80 of them so be patient!
How to replace tail light bulb Jeep Liberty 2005-2007?
How to remove and replace tail light bulbs in a 2005 – 2007 Jeep Liberty. This is very easy to do and can be completed in a short amount of time. Buy your new tail light bulbs and then the only tool needed is a T20 Torx bit / screwdriver. Loading…
Where are the brake lights on a Jeep Cherokee?
There are usually three lights in the Jeep Cherokee rear taillight assembly and the top one is the brake light. Twist the back of the bulb counterclockwise to remove the bulb from the back of the assembly.
How do you put a brake light back together?
Twist the back of the bulb counterclockwise to remove the bulb from the back of the assembly. Pull the brake light out of the socket and insert the new bulb. Have a helper step on the brake pedal to ensure the light is working before putting the assembly back together.
Where can I change the brake light bulbs?
The bulbs are easy and quick to change and quite affordable at the auto parts store. Go ahead and change the brake lights yourself and save some money on labor charges. Lift up the rear hatch. Locate the two screws on the rail of the hatch at the side of the rear taillight assembly. Remove the two screws with the screwdriver.
What to do if your Jeep Liberty is having trouble stopping?
If your Liberty is having trouble stopping, or noticeably leaking fluid, don’t drive it. Just have it towed to a mechanic. If you mess up fixing your engine, the vehicle does not move. If you mess up fixing the brakes, it doesn’t stop.
Why is the brake light on in my Chevy Impala?
Either the brakes need bled, or there is a leak. Since you’ve already checked the emergency brake handle, now it’s time to check the master cylinder and see if the brake fluid is low or not. Now if it is low, but not empty, adding more may provide a temporary fix.
Why does my brake light only come on when I push the brakes?
If the brake light is only coming on when you push the brakes, that’s a definite indication that the pressure in the brake system is too low. Either the brakes need bled, or there is a leak. Since you’ve already checked the emergency brake handle, now it’s time to check the master cylinder and see if the brake fluid is low or not.
What are the symptoms of a bad brake light switch?
The most common symptom of a faulty brake light switch is when brake lights don’t come on or stay on all the time. A faulty brake light switch can cause many problems. If a switch is bad, the brake lights won’t operate and the transmission shifter will not come out of “Park” position.
Where is the brake light switch on a car?
January 30, 2017. Brake light switch is a small device attached to the brake pedal mechanism. Despite its small size, the brake light switch plays an important role in a modern car. Brake light switch is installed above the brake pedal.
How to replace a tail lamp brake light?
Make sure your lights are switched off and the key is not in the ignition before beginning the replacement. See your owner’s manual for proper bulb type and wattage. Loading…
Why does my brake light only work on one side?
Since the problem is only on one side, you can rule out the fuse and other parts of the circuit that are shared by both bulbs. I would look closely at the connector for the nonfunctional bulb, as it may be damaged or corroded. If the bulb looks OK, you’ll want to test for power and ground at the bulb.
Are there any problems with the Jeep Liberty?
Other Common Exterior Lighting related problems of Jeep Liberty Problem Category Number of Problems Headlight Switch problems 15 Tail Light Switch problems 12 Turn Signal problems 8 Fog Light Switch problems 4
Brake light replacement. Needed: Sylvania 3157 bulb, 10mm socket, T-20 star bit. Wrench. I used a power wrench but a manual socket wrench works fine too. Takes 5 minutes. Same process works for changing amber light or tail light. This is a 2011 Jeep Liberty but the process is the same for 2008, 2009, 2010, 2011, and 2012 Jeep Liberty. Loading…
How to remove and replace tail light bulbs in a 2005 – 2007 Jeep Liberty. This is very easy to do and can be completed in a short amount of time. Buy your new tail light bulbs and then the only tool needed is a T20 Torx bit / screwdriver. Loading…
Why is my passenger side brake light not working?
The brake light (passenger side) went out. I replaced the bulb and the other one while I was at it. But the passenger side brake light still doesn’t work. Even tried switching bulbs to use the one that I knew was working on driver’s side, but still wouldn’t work on passenger side. I see that there’s only one fuse control for both lights.
Why does my third brake light fall out?
Third brake light rust, due to poor seal and design. Cost hundreds of dollars in repairs, which is silent until the light falls out and damage is beyond a simple repair. I was alerted to this by the auto body shop, that told me it was common in Jeep Liberty, and did my research.
Why is the brake warning light on on my Jeep Liberty?
Doing so may lead to injury when the brakes fail. The brake warning light indicates that your Liberty has detected that one of its major brake components has failed, typically detected through a loss of pressure. You’ll feel a loss of pressure that manifests itself in the form of a “mushy” brake pedal.
If your Liberty is having trouble stopping, or noticeably leaking fluid, don’t drive it. Just have it towed to a mechanic. If you mess up fixing your engine, the vehicle does not move. If you mess up fixing the brakes, it doesn’t stop.
Why does my brake light only come on when I press the brake pedal?
You’ll feel a loss of pressure that manifests itself in the form of a “mushy” brake pedal. If the brake light is only coming on when you push the brakes, that’s a definite indication that the pressure in the brake system is too low. Either the brakes need bled, or there is a leak.
Why are the brakes on my Jeep sticking?
This happened several times. Does anyone have an idea on why it does this? Click to expand…