How do you test the ignition switch on a Honda Accord?
To test the ignition switch: Unplug the ignition switch’s 6 pin connector from the driver-side fuse/relay box. Place your multimeter in Ohms mode. Using the illustration below: Your multimeter should register continuity between. LOCK position: NO CONTINUITY between any terminal.
Why did my Honda Accord DX shut itself off?
A couple of years ago my 1998 Honda Accord Dx started shutting itself off at random times — on freeway onramps, while parked and idling, etc. — so I did some research and found that the electrical portion of the ignition switch had been recalled.
Why is the master switch on my accord not working?
This switch is prone to malfunction if the power wires connected to it are damaged, and no longer transmitting power. Among the Accord community, owners admit that damage to the master switch is largely attributed to spilled beverages, or if the windows are left open when it rains.
How many wires are in the Honda ignition switch?
These are: LOCK (Off), ACC, ON, and START. Although the ignition switch has slots for 6 wires… the switch itself only has 5 wires. In layman’s terms, the ignition switch simply ‘opens’ or ‘closes’ certain circuits (wires) together as you rotate the ignition key to crank and start your Honda.
What is the transmission solenoid on a 2002 Honda Accord?
Honda Accord 2002, Automatic Transmission Control Solenoid by Genuine®. If your transmission is in need of repair, don’t compromise the performance and safety of your car with suspect, off-brand replacement parts from the local auto… Honda Accord Automatic Transmission 2002, Automatic Transmission Oil Pressure Switch by World Source One®.
Where is the ignition switch on a Honda Accord?
Begin on the left side and gently pull it off, so that all of the retaining clips are released. The ignition switch can now be unplugged for testing. The switch connects to the rear of the driver’s side fuse panel. Shine a flashlight and find the connector highlighted in red.
Where is the shift release lock on a Honda Accord?
If you’re crunched for time and need a temporary fix, you can use the shift release lock next to the shift lever. It is located above and to the right of the the shift lever. Simply insert and push a flat head screwdriver or a key into the little slot.
This switch is prone to malfunction if the power wires connected to it are damaged, and no longer transmitting power. Among the Accord community, owners admit that damage to the master switch is largely attributed to spilled beverages, or if the windows are left open when it rains.
What should you know about a car diagnostic test?
Diagnostic tests can reveal problems within a car’s engine, transmission, exhaust system, brakes, and other major components, as well as performance issues with the fuel injector, air flow and coolant, ignition coils, and throttle. However, a common misconception about car diagnostic tests is…
When to do a TPMS re-calibration in Honda Accord?
A TPMS re-calibration is recommended when changing air pressure, rotating tires and replacing a tire or TPMS sensor. Direct TPMS system (2008-2012) requires TPMS scan tool with OBD module to connect to the vehicle’s DLC ( VT56 or VT46 brands), step by step relearn procedures are written in the tool.
How can I diagnose a Honda transmission problem?
A scanner that can diagnose Honda transmission problems. Here are a few popular choices. These scanners can read and clear fault codes from the transmission module. Locate the OBD-II port under the dashboard. Turn on the ignition. Allow your scanner to turn on. Select your Honda model, then go to the Control Unit.
Where is the diagnostic port on a Honda Accord?
For the 1990 to 1995 Honda Accords, the diagnostic port is located by the passenger’s side kick panel. To access the connector, remove the panel using a Phillips screwdriver. For the 1996 to 2002 Honda Accords, the diagnostic port is located just bellow the bottom edge of the driver’s side dash.
Why do I need a scan on my Honda Accord?
Scanners deliver expensive diagnostic reports every time the check engine light turns on, and lets you monitor the health of your car from the comfort of your own garage. These simple tools allow you to diagnose a problem as it arises.
Where can I find the DTC code on my Honda Accord?
On an OBD-I scanner, you will be able to retrieve codes through a series of flashes. Each DTC corresponds to a different problem in your vehicle. Search through the Honda Accord’s automotive repair manual or search online for the DTC to diagnose the exact problem, and then decide how to repair it. Figure 5.
What does a multimeter tell you about a Honda Accord?
CASE 1: Your multimeter registered 13.5 to 14.5 Volts. This is good and it tells you that the alternator is working and is charging the battery and providing enough juice for the electrical needs of your Honda Accord, or Odyssey or Prelude.