How do you replace the serpentine belt on a Toyota?

How do you replace the serpentine belt on a Toyota?

An adjustment bolt on the alternator provides belt tension on Toyota’s 1.8L engine. This belt is easier to replace than many, but does require that the alternator mounts are loosened up.

What should tension be on a serpentine belt?

2) Turn the adjustment bolt clockwise until the rearmost length of the thread matches up with mark on the paper made earlier. Check the tension on the belt. There should be 1/2″ of deflection at the midpoint of the longest straight run of the belt.

How do you replace a serpentine car battery?

There should be 1/2″ of deflection at the midpoint of the longest straight run of the belt. 3) Tighten the lower 14mm pivot bolt. 4) Tighten the upper 12mm mounting bolt, below the adjuster. 5) Re-connect the battery. 6) Test. Numerous boisterous screeching clamors or other general motor commotions can be followed back to your serpentine belt.

An adjustment bolt on the alternator provides belt tension on Toyota’s 1.8L engine. This belt is easier to replace than many, but does require that the alternator mounts are loosened up.

How is the tension set on a serpentine belt?

Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.

Where do I find the serpentine belt routing diagram?

Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.

What happens if a serpentine belt goes bad?

The serpentine belt in most modern vehicles transfers power from the crank pulley to the various accessories mounted on the engine. A worn or damaged serpentine belt can fail to adequately transfer the power, leaving your alternator, power steering, and air conditioning failing to function.

How to change the serpentine belt on a 2006 Pontiac G6?

Jack up the front of the 2006 Pontiac G6 and place the jack stands under the designated jacking points on both sides of the vehicle. Lower the vehicle onto the stands and leave the jack upright. Reach in behind the passenger side front tire and remove the plastic cover from the wheel well. The plastic cover is held on by small plastic clips.

What happens when you loosen a serpentine belt?

If your vehicle uses the alternator bracket to apply tension to the belt, loosen the two bolts that pass through the long eyelets on the bracket. As you loosen the bolts, the tension on the belt will likely move the alternator toward the engine and relieve the pressure. Loosen the bolts enough to move the alternator, but don’t remove them.

What kind of pulley does a serpentine belt use?

Determine if there is a belt tensioner pulley. Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times.

What’s the best way to replace a serpentine belt?

Auto tensioners have either a hole that will fit a half inch drive ratchet, or a bolt you can use a socket to apply pressure to. Insert the wrench or place the socket over the bolt on the tensioner and twist it away from the belt to relieve the tension on it.

How to loosen the belt on a Toyota Corolla?

To loosen an over tightened belt, loosen the lower 14mm bolt, loosen the upper 12mm bracket bolt and then rotate the long 12mm tensioner bolt a few turns in the counterclockwise direction. Be careful when touching the belt as it may have become hot from spinning.

What kind of belt does a Toyota use?

The Toyota engine uses a serpentine belt to rotate many of the accessories of the engine, such as the air conditioning compressor, the alternator, the power steering pump and the water pump.

What to do if your serpentine belt is still hot?

When you check on the serpentine belt, turn off the Toyota and let the engine cool. You don’t want to risk burning your hand by working near an engine when it’s still hot.

Where can I get a replacement belt for my Toyota Corolla?

Please verify the correct replacement belt part number for your Corolla by calling your dealership, consulting with an automotive parts store or by using the Amazon Part Finder website since it may vary by model year, trim level, engine type and whether it was built in North America (Canada) or in Japan.

The Toyota engine uses a serpentine belt to rotate many of the accessories of the engine, such as the air conditioning compressor, the alternator, the power steering pump and the water pump.

When you check on the serpentine belt, turn off the Toyota and let the engine cool. You don’t want to risk burning your hand by working near an engine when it’s still hot.

Use a drive socket wrench to release the tensioner pulley, which holds the old serpentine belt tight against the other pulleys. This is the hardest part of the process. You may need to use a lot of force to free the bolt that holds the tensioner pulley in place. Once it’s released though, the serpentine belt will easily slip off the other belts.

What should the back of a serpentine belt look like?

The back side of the belt runs against the tensioner, so it will appear more like a smooth roller than a pulley. Position the wrench or special removal tool on the tensioner, ensuring you have room to remove the tool once the tensioner is released.

Where is the serpentine belt on a power steering pump?

To remove the serpentine belt, loosen the tensioner pulley that is located on the left side of the motor (as you’re looking at the motor). Once the tensioner pulley is loose, you can slip the belt off rather easily. If your power steering pump is driven by the drive belt, you’ll have to remove this belt as well.

When did Toyota Camry stop using serpentine belt?

For this reason, the 2.5L I4 introduced in 2010 included electric power steering (EPS), thus eliminating a belt connection to a vane pump (the hybrid version of the 2.4L engine always used EPS). Because the space is so tight, replacing the serpentine belt in a Toyota Camry is a difficult chore.

What’s the best tool to replace a serpentine belt?

This tool pays for itself ten times over the first time you use it to replace your serpentine belt. The serpentine belt tool kit makes it easy to precisely position idler pulleys and get belts set to the perfect tension. Fits idler pulleys requiring 15mm or 18mm hex or 3/8 in. or 1/2 in. square drives

How often to replace serpentine belt Toyota Nation Forum?

Is yours a 4 cyl or v6 had no problems taking my tensioner off when changing the water pump to get better access to the bolts. Were you using deep sockets maybe? Is yours a 4 cyl or v6 had no problems taking my tensioner off when changing the water pump to get better access to the bolts. Were you using deep sockets maybe? Click to expand…

How does the serpentine belt work on a car?

As your engine runs, the spinning motion of the crankshaft is transferred to each of the accessory pulleys via the serpentine belt. If your vehicle is supercharged, the serpentine belt also powers the supercharger. Older engines have v-belts instead of serpentine belts.

Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.

How often should a serpentine drive belt be used?

The serpentine/drive belt on your car is a crucial consideration, and it should be inspected at every maintenance interval (every oil change). The belt is in use every single time you start your engine, and it is used for as long as the engine is running.

How to replace serpentine belt on Toyota Corolla?

1.8L Toyota Corolla S Serpentine Belt replacement. Get slack on the tensioner and pull the belt at the alternator, make a diagram of how the belt is routed so you refer back to it to get it back on. Take your time and work on it when the engine is cold cause it sucks to get burned.

How much does it cost to replace the drive belt on a Toyota Corolla?

Upfront and transparent pricing. Toyota Corolla Serpentine/Drive Belt Replacement costs $137 on average. What is a serpentine belt and how does it work? A serpentine belt is a relatively long, flat, multi-ribbed belt that is driven by the engine’s crankshaft pulley.

How to replace drive belt or serpentine belt?

How to replace drive belt or serpentine belt Toyota Corolla. VVT-i engine. Years 2000-2009. – YouTube

When to replace serpentine belt on Toyota Yaris?

An adjustment bolt on the alternator provides belt tension on Toyota’s 1.8L engine. This belt is easier to replace than many, but does require that the alternator mounts are loosened up. This engine was used from 2009 to 2013 and is also found on the Yaris, Matrix, Scion xD and Pontiac Vibe.

How do you remove a belt from an auto tensioner?

Hold the tension from the belt, and slip the belt off the auto tensioner pulley to remove the belt and pulley system. Slowly release the tension to avoid damage or injury, and then remove the tool from the belt auto tensioner.

How do you remove a pulley belt from a car?

With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well. Compare the new belt to the old one.

How to check the belts on a Toyota Echo?

Check the Belts: 2000-2005 Toyota Echo 1. Getting Started – Prepare for the repair 2. Open the Hood – How to pop the hood and prop it open 3. Check Belts – Determine the proper amount of ‘give’ 4. More Info. – Additional thoughts on checking the belts Share on Intl. Autoshelped make these videos Feedback Download Toyota owners manuals

How to setup drive belt or serpentine belt?

How to setup drive belt or serpentine belt Toyota VVT-i engine. VERY DETAILED INFO If playback doesn’t begin shortly, try restarting your device.

How to plug oil leak in Toyota Echo?

Plug the oil leak If you are leaking oil and parking on your oil spots each night, the oil is breaking down your tires’ rubber 2001 Toyota Echo 1.5L 4 Cyl. (4 Door) How to add transmission fluid If your transmission is running low on fluid, be sure to add some – find out how to do this here! 2001 Toyota Echo 1.5L 4 Cyl. (4 Door)

How to check the fuse on a 2001 Toyota Echo?

2001 Toyota Echo 1.5L 4 Cyl. (4 Door) Check power steering fluid level Power steering fluid is easy to check and many people (mechanics included) often forget about – learn how here 2001 Toyota Echo 1.5L 4 Cyl. (4 Door) Check for a blown interior fuse

What makes up the serpentine belt in a car?

A serpentine belt is a relatively long, flat, multi-ribbed belt that is driven by the engine’s crankshaft pulley. The belt drives many, and often all, of the engine accessories such as the alternator, air conditioning compressor, power steering pump, water pump, and air pump.

Where is the alternator on a Toyota Corolla?

Then move to the left (passenger) side of the engine bay and locate the alternator at the top of the engine. Unlike our 2005 Corolla which has a spring loaded automatic tensioner arm with the “fake bolt” for releasing the tension, the newer 09-13, 2014 & 2015 models use a long bolt in a bracket attached to the alternator for tensioning the belt.

What happens if the serpentine belt goes bad?

Serpentine belt problems that result in the alternator not charging may cause the battery to discharge, which will result in loss of electrical power to the vehicle. Additionally, if a deteriorated belt breaks and that belt drives the water pump, the engine will overheat in a matter of seconds.

How to replace accessory belt on Toyota Corolla?

Place the new belt down on to the left (passenger) side of the engine and wrap the ribbed side around the lowest large pulley near the rear of the engine. Then bring it upwards and wrap the smooth side over the tensioner pulley and continue to the upper pulley at the rear of the engine and wrap the ribbed side over it.

2) Turn the adjustment bolt clockwise until the rearmost length of the thread matches up with mark on the paper made earlier. Check the tension on the belt. There should be 1/2″ of deflection at the midpoint of the longest straight run of the belt.

There should be 1/2″ of deflection at the midpoint of the longest straight run of the belt. 3) Tighten the lower 14mm pivot bolt. 4) Tighten the upper 12mm mounting bolt, below the adjuster. 5) Re-connect the battery. 6) Test. Numerous boisterous screeching clamors or other general motor commotions can be followed back to your serpentine belt.