How do you install choke control on a car?
2. Place the choke control cable under the intake manifold from the front of engine (front pull choke). Insert the cable bowden wire into the choke control (front or reverse pull). Then place choke cable under the cable clamp. 3. Position the choke control so it bottoms, then pull it back approximately 1/16″ (1.5 mm).
What to do if your dirt bike only runs on choke?
If the leak is on the air boot to carburetor connection, then tighten that clamp. This should fix it unless there is a crack in the air boot. If there is a crack, you will need to replace the air boot. If the leak is on the vacuum lines, then it is easiest to just replace the offending line.
Where is the choke and throttle cable located?
Insert the control cable bowden wire in the proper hole of the engine control lever, which is located on the side of the carburetor air intake elbow.
2. Place the choke control cable under the intake manifold from the front of engine (front pull choke). Insert the cable bowden wire into the choke control (front or reverse pull). Then place choke cable under the cable clamp. 3. Position the choke control so it bottoms, then pull it back approximately 1/16″ (1.5 mm).
Where can I find a Suzuki motorcycle wiring diagram?
Suzuki TS185 TS 185 Electrical Wiring Harness Diagram Schematics HERE Suzuki TS250 TS 250 Electrical Wiring Harness Diagram Schematics HERE Suzuki VL1500 Intruder VL 1500 Electrical Wiring Diagram Schematics 1998 – 2004 HERE Suzuki VS1400 VS 1400 Electrical Wiring Harness Diagram Schematics 1996 1997 HERE
What kind of wiring harness does a Suzuki gsxr600 use?
Suzuki GSXR600 GSXR 600 Electrical Wiring Harness Diagram Schematic 2001 – 2003 HERE Suzuki GSXR750 GSXR 750 Electrical Wiring Harness Diagram Schematic 1991 1992 HERE
What kind of wiring harness does a Suzuki gv2500 use?
Suzuki GV1200 Madura GV 1200 Electrical Wiring Diagram Schematics 1985 1986 HERE Suzuki GZ250 Marauder GZ 250 Electrical Wiring Harness Diagram Schematics HERE Suzuki K50 K 50 Electrical Wiring Harness Diagram Schematics HERE
How to install a H-D Twin Cam camshaft?
Align timing marks and torque retaining bolts in the correct sequence as listed in manual. Install push rods adjust to the shortest length rocker arm end first. Rotate motor so pushrod is on the base circle and adjust pushrod to zero lash. Adjust pushrod per manufacturer’s specs and tighten jam nut (generally 2.5-4 turns depending on thread pitch).
What should I do if my choke does not work?
If the engine does not start when cranked over for a few seconds, release the key and press the accelerator to the floor one more time to evoke an additional accelerator pump shot. Most automatic chokes have a “clear flood” mode or “unloader” that is carburetor-linkage operated.
How to install a camshaft on a fuel Moto engine?
Make sure to align the timing marks on the cams Replace inner cam bearings and install the cam plate into the engine. Note: if you have not removed or serviced the oil pump from the cam plate you can simply re-install the camplate, however if you have removed or replaced the oil pump it will need to be aligned.
When to move throttle control to slow or fast?
Move the application throttle control to the slow position, then to fast. Check the engine control to assure it stops against the high idle RPM stop bracket. NOTE: When the application throttle control lever is in the slow position the engine governor spring must be free of tension or pushing pressure. A non- free spring can affect the RPM.
Where is the throttle cable in a car?
Position the application throttle control in the fast throttle position. Then move the throttle control back 3/16″ (4.75 mm). Insert the control cable bowden wire in the proper hole of the engine control lever, which is located on the side of the carburetor air intake elbow.
How do you put throttle control on a car?
Grasp the control cable and place it under the cable clamp. Pull until the cable is taut, then tighten the clamp screw. NOTE: The engine control lever should be against the high idle RPM stop bracket. 6. Move the application throttle control to the slow position, then to fast.
How to install a choke control on a carburetor?
Insert the cable bowden wire into the choke control (front or reverse pull). Then place choke cable under the cable clamp. 3. Position the choke control so it bottoms, then pull it back approximately 1/16″ (1.5 mm). Make sure that the carburetor choke is fully opened before tightening cable clamp. 4.
Move the application throttle control to the slow position, then to fast. Check the engine control to assure it stops against the high idle RPM stop bracket. NOTE: When the application throttle control lever is in the slow position the engine governor spring must be free of tension or pushing pressure. A non- free spring can affect the RPM.
How to adjust throttle control on a car?
Pull until the cable is taut, then tighten the clamp screw. NOTE: The engine control lever should be against the high idle RPM stop bracket. 6. Move the application throttle control to the slow position, then to fast. Check the engine control to assure it stops against the high idle RPM stop bracket.