How do you hook up an existing sewer line?

How do you hook up an existing sewer line?

How to Tie Into Existing Drain Line

1. Step 1 – Cut Out Old Pipe. Remove a section of the existing pipe to the same size of the pipe you want to add in.
2. Step 2 – Insert Couplings. Slide a coupling onto both sides of the remaining pipe.
3. Step 3 – Lay in New Pipe.
4. Step 4 – Tighten Couplings.
5. Step 5 – Test for Leaks.

What is the old sewer pipe called?

Orangeburg
In older properties built before the 1950s, you might find clay pipe, cast-iron pipe, or a fiber conduit pipe called Orangeburg. Clay and cast-iron are older types of sewer piping and can remain in the ground as long as they are still moving the waste with no leaks.

What is a lateral sewer connection?

A private sewer lateral (PSL) is the pipe that connects your home’s plumbing to the publicly-owned sanitary sewer line, usually located under your street. This crucial pipe carries all of the waste water from your home to the sewer, including everything washed down your sink or flushed down your toilet.

What size are sewer laterals?

4 inches
The sewer lateral is a buried pipe (typically 4 inches in diameter) that connects a building’s plumbing system from the foundation to the public sewer main located in the street, an alley, or an easement.

What material is used for sewer pipes?

While that’s an important standard, there are other factors that determine what makes a great material for sewer pipes. The common materials used are concrete, steel, clay, and plastic (HDPE and PVC).

Where is the sewer lateral?

A sewer lateral is the section of pipe from the property line to the mainline sewer in the street. This section is sometimes referred to as the “public” side. The section of pipe between the property line and the structure is called the building sewer. This section is sometimes referred to as the “private” side.

What is side sewer?

A “side sewer” is a privately owned sewer pipe that carries wastewater from a building’s sinks, drains, and toilets to the public sewer mainline. If you own your home or building, you also own your side sewer up until the public sewer pipe under a street near your home.

How do you maintain sewer laterals?

7 Tips on How to Maintain Your Sewer Line

1. Tip #1 Limit Food Down the Kitchen Drain Line.
2. Tip #2 Properly Dispose of Non-Food Items.
3. Tip #3 Use One-Ply Toilet Paper.
4. Tip #4 Flush the Plumbing System.
5. Tip #5 Set Toilets to High Volume Flush.
6. Tip #6 Tend to Your Roots.
7. Tip #7 Naturally Clean Your Plumbing System.

How do you measure a sewer pipe?

A standard rule of thumb is that sewer pipes leading away from a toilet are 3 inches in diameter. Sewer drains from laundry sinks or washing machines are 2 inches in diameter and those from sinks in the kitchen, bathroom or powder room generally use a 1.5-inch pipe.

How are laterals made in a sewer line?

existing sewer line and a new wye/tee must be installed, lateral connections shall be made as follows: a. PVC Pipe Lateral connections shall be made with a saddle type connection. The hole for this saddle must be carefully cut into the existing line, making sure that the cut-out piece is not dropped into the pipe. All saddles shall be securely

What should be the slope of sanitary sewer laterals?

Sewer laterals shall be designed so that all units shall be served by a minimum 6-inch sewer lateral. Laterals shall be installed with a minimum 1% slope and shall include a watertight cap or stopper. All sanitary tees shall be set in accordance with the detail drawings using 6-inch bends. The invert elevation

What kind of tees are used for PVC laterals?

Lateral Connections to Existing Sanitary Sewer Lines Saddles used to connect laterals to existing PVC sanitary sewer lines shall be molded tees, gasket branch and gasket skirt and shall have two stainless steel straps. Saddle tees installed on PVC pipe shall be solvent-weld type saddles by GPK Products, Inc. or approved equal.