How do you change the disc brake on a Honda Civic?
Remove the spindle nut. Use pliers to remove the retainer springs inside the drum brake assembly, and to safely unhook the emergency brake cable from the brake shoes. Once all the hardware is taken off, use a 12mm open-ended wrench to close the tangs at the end of the brake cable, and pull it from the drum assembly.
How do you replace the drum on a Honda Accord?
Thread two bolts–size 8 x 1.25 millimeters–into the brake drum’s threaded holes to remove the drum from the hub. Thread each bolt two turns at a time. Insert a small, thin piece of wood, like a paint stick or ruler, in between the wheel cylinder and the rear brake shoe.
What kind of brake cables do you need for a 1999 Honda Civic?
Use the 1999-2000 Civic Si e-brake cables. This model also comes with rear disc brakes, so this would be a nice upgrade over the drum brake setup. Skill Level – Difficult; you will need mechanical skills. Front: Take the Civic EX or Si’s knuckle with bearing and hub.
How do you jack up a Honda Civic?
Break loose the lug nuts before you raise the car. (Related Article: How to Jack Up Your Civic – Honda-Tech.com) Use an 8 x 1.25mm bolt and thread it into the drum brake holes. This will lift the drum covers up to reveal the braking assembly. Then, use a flat head screwdriver to remove the dust cap.
Remove the spindle nut. Use pliers to remove the retainer springs inside the drum brake assembly, and to safely unhook the emergency brake cable from the brake shoes. Once all the hardware is taken off, use a 12mm open-ended wrench to close the tangs at the end of the brake cable, and pull it from the drum assembly.
Break loose the lug nuts before you raise the car. (Related Article: How to Jack Up Your Civic – Honda-Tech.com) Use an 8 x 1.25mm bolt and thread it into the drum brake holes. This will lift the drum covers up to reveal the braking assembly. Then, use a flat head screwdriver to remove the dust cap.
How do you Bleed the brakes on a Honda Civic?
Open the bleed bolt on the caliper, place a clear vacuum hose on it, and then submerge the other end into a bottled filled with brake fluid. Pump and pedal, while checking the reservoir every several pumps to ensure it stays filled. Continue pumping the brake until it’s firm. Figure 10. Bleed the brakes.
What’s the best way to remove a brake drum?
Use a screwdriver to attach the brake drum puller’s screw tightly. Tighten the screw until the brake drum puller is securely fastened around the brake drum. Do not over-tighten the screw on the brake drum puller. Knock the back of the brake drum lightly with a hammer. Tap the hammer against the brake drum with an outward motion.
Open the bleed bolt on the caliper, place a clear vacuum hose on it, and then submerge the other end into a bottled filled with brake fluid. Pump and pedal, while checking the reservoir every several pumps to ensure it stays filled. Continue pumping the brake until it’s firm. Figure 10. Bleed the brakes.
How to install rear disc brake conversion kit?
Install the conversion bracket. Re-install the hub and torque the spindle down to 134 ft/lbs. Mount on the new rotors along with the caliper and brake pads. The new calipers will require a different brake hose. Disconnect the old hose from the chassis, and install a new one. The bracket that holds the hose will also need to be changed. Figure 8.
Which is better disc brakes or drum brakes?
Drum brakes are quickly becoming a thing of the past. Disc brakes offer better stopping performance for your car. This article will explain how to use a conversion kit to upgrade from drums to rear disc brakes. This article applies to the Honda Civic/Del Sol (1992-2000).
How can I get old brake fluid out of my Honda Civic?
This can be done using a vacuum brake bleeder or by sucking it out the old fluid from the reservoir with a turkey baster. This should remove any contaminated fluid. Afterwards, fill the master cylinder with enough new brake fluid to wash out the old fluid away. Figure 1. Siphon old brake fluid from the brake fluid reservoir.
Use a screwdriver to attach the brake drum puller’s screw tightly. Tighten the screw until the brake drum puller is securely fastened around the brake drum. Do not over-tighten the screw on the brake drum puller. Knock the back of the brake drum lightly with a hammer. Tap the hammer against the brake drum with an outward motion.
How do you adjust the brake drum on a car?
Place the brake drum onto the wheel hub. Pump the brake pedal several times. Insert a screwdriver into the hole located on the backing plate and turn the adjuster star wheel. Continuing turning the star wheel until the drum drags against the shoes, then back it off until it no longer drags.
Where does the bleeding start on a Honda Civic?
Siphon old brake fluid from the brake fluid reservoir. Brake bleeding begins with the rear passenger side wheel, followed by the rear wheel on the driver’s side. Then, the front passenger side wheel and lastly the drivers side wheel. Remove the cap from the brake bleeder valve and loosen it with a box end wrench. Do not open it.
How do you stop brake bleed on Honda Civic?
Figure 1. Siphon old brake fluid from the brake fluid reservoir. Brake bleeding begins with the rear passenger side wheel, followed by the rear wheel on the driver’s side. Then, the front passenger side wheel and lastly the drivers side wheel. Remove the cap from the brake bleeder valve and loosen it with a box end wrench. Do not open it.
When to change brake fluid in Honda Civic?
Once you finish bleeding the brakes, refill the brake master cylinder reservoir with brake fluid. Always ensure the master cylinder reservoir has the brake fluid. Honda motoring experts advise that brake fluid should be changed or flushed after around 30,000 miles.
Where is the brake line on a Honda Civic?
Locate the brake line that extends from the brake caliper. It is attached to the wheel bearing housing by two 10mm bolts; remove to free up the line for more room to move around later. Remove two 17mm bolts holding the brake caliper bracket.
How do you replace a brake line on a Honda Civic?
Disconnect line at all points. Try to keep the brake fluid from splashing onto the paint of your car. The fluid causes permanent damage to the finish. Loosely thread the new line into place. Using a new retaining clip, secure the line to the top mounting bracket.
Are there any parts to repair a Honda Civic?
As a result, we provide an extensive selection of high quality Honda Civic repair parts manufactured to restore your vehicle to like new condition at the most attractive prices. No matter whether you are changing an air filter or doing a routine brake job on your Honda Civic, we have everything for your repair and maintenance needs.
Where is the bleed screw on a Honda Civic?
Bleed screw is located on the caliper. Always keep an eye on the brake fluid reservoir. Never let this fall below half full when bleeding the brake system. (Related Article: How to Bleed Your Brakes – Honda-Tech.com) Attach your wheels back on, and tighten the lug nuts all the way down by hand.
How do you stop a foot bleed on a Honda Civic?
Tighten the screw back down, and have someone get in the car. To foot bleed, your helper needs to pump the brake pedal three times and hold it down to pressurize the hydraulic system. Loosen the bleed screw to relieve pressure, and allow the fluid to escape. Twist the screw closed to seal the system off again.
Drum brakes are quickly becoming a thing of the past. Disc brakes offer better stopping performance for your car. This article will explain how to use a conversion kit to upgrade from drums to rear disc brakes. This article applies to the Honda Civic/Del Sol (1992-2000).
Can a rear disc brake be converted on a Honda Civic?
Professional brake conversions are very costly, and this article will help alleviate the costs by showing you how to safely perform a rear disk brake conversion using a conversion kit on your Honda Civic. Use a lift, and raise the rear of the vehicle up.
How do you release the brakes on a Honda?
A caliper wind back tool is used to compress the brake piston back into the caliper. There is a manual release on the actuator if you don’t release the brakes using the button. It requires a E11 TORX socket.
How do you replace a Honda drum brake?
Comparison of worn and brand new shoes. Putting the e-brake clamp onto the new shoe. Use some pliers to squeeze the new shoe-horn clamp over the little bolt thingy. Presto! Grab some white grease and dab the 3 contact points on the mounting plate where each shoe will make contact.
How are rear disc brakes and drum brakes different?
On drum brakes the emergency brake job is done by the rear brake shoes. A mechanical activation system of the emergency brake uses the same principle of forcing the shoes outward against the drum helping to hold the car in place. Vehicles with rear disc brakes will use a smaller drum brake in the center of the rotor for the emergency brake.
What’s the best way to replace a drum brake?
Remove the spring and immediately hook it onto the new shoes exactly as you removed it. Inspect the brake wheel cylinder for any signs of leakage and replace if needed. Rebuild the new brake. The brake backing plates should be cleaned and lubed with a small amount of anti-seize on the slide points and anchor points.