How do you change brake pads on a GMC Sierra?
Remove the jack stands and lower the vehicle to the ground. Slowly apply brake pressure with the brake pedal until it is 2/3 of the way to the floor. Slowly release the brake pedal and wait 15 seconds. Repeat this process until the brake pedal is firm.
What should I do when I replace my radiator?
With all the hoses and bolts attached, fill the new radiator with coolant. Check oil and transmission fluid levels in case any was lost during the installation. This is an excellent time to flush your coolant system and replace the old coolant with new coolant.
How much does it cost to replace a brake rotor on a Sierra?
Upfront and transparent pricing. Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. GMC Sierra 1500 Brake Rotors/Discs Replacement costs $401 on average. What is the Brake Rotor/Disc all about?
Can a car jack be used to replace a radiator?
You’ll need to raise the vehicle so you can access your radiator. You can use a car jack and stands to keep the vehicle up, but remember to put a chock behind the wheels and engage the parking brake. Wait until the engine is cold before proceeding. This job can be dangerous, so be extra careful.
How long does it take to replace a radiator?
Replacing a radiator can take most of a day, but, with care and patience, it is is doable. In order to replace a radiator, you’ll need to drain the old radiator, detach any the parts keeping it in place, remove it, install a new radiator, re-install any parts that were removed, and add coolant.
You’ll need to raise the vehicle so you can access your radiator. You can use a car jack and stands to keep the vehicle up, but remember to put a chock behind the wheels and engage the parking brake. Wait until the engine is cold before proceeding. This job can be dangerous, so be extra careful.
How do you remove a radiator from a car?
Many radiators can be removed by lifting up and out of the vehicle, but some need to be removed from underneath the vehicle. Set the new radiator in place, and then reattach all the previously removed parts. Start with the radiator mounting bolts and finish with the radiator reservoir hose.
Is it dangerous to replace a radiator in a car?
Wait until the engine is cold before proceeding. This job can be dangerous, so be extra careful. You will encounter sharp edges and other circumstances that could cause injury. Protect yourself by wearing quality safety gloves and goggles. Be watchful of any moving items while working.
What happens when one brake is stuck on a GMC Sierra?
Pulling to one side – When one brake is stuck (particularly a front brake) the whole vehicle will pull in the direction of the bad brake. So if it is on the passenger side, your Sierra will feel like it is steering in that direction.
How to remove a GM 8.25 ” front differential?
Use some tie wire and tie the axles up, if they dangle and hang down it will make it more difficult to remove the diff. Unplug the actuator wiring harness and loosen the 3 clamps holding the harness. Unbolt the driveshaft and tie it out of the way. Loosen the upper mounting bolt and remove the nut, leave the bolt in place.
How do you turn off the wipers on a GMC Truck?
Turn it forward into the accessory position, but don’t start your truck. Turn on the power to your GMC truck’s windshield wipers. When the wipers reach their highest point on the glass, turn the ignition key back into the off position. Remove the ignition key and exit the truck.
Remove the jack stands and lower the vehicle to the ground. Slowly apply brake pressure with the brake pedal until it is 2/3 of the way to the floor. Slowly release the brake pedal and wait 15 seconds. Repeat this process until the brake pedal is firm.
What’s the best way to disassemble a Chevy differential?
It depends on your preference and tools available. The first step is to use a socket and ratchet or a wrench to remove the cover bolts. Use a soft mallet to break the seal or use a pry bar, but be careful not to damage the mounting surface of the center section.
How to remove pinion seal from Chevy differential?
Pinion Yoke Removal 1 Remove Pinion Nut A fair amount of torque is required for removing the pinion nut. 2 Remove Yoke A few blows with a soft hammer usually gets the yoke free from the splines. 3 Remove Pinion Seal (Special Tool)
What’s the first step in disassembling a Chevy?
The first step is to suspend the chassis and let the rear extend freely under the car. Use the properly rated floor jack to jack up the car and place the correct jackstands under the frame rails. Remove the lug nuts and take off the rear wheels. The shocks are fully extended and can be unbolted.
What kind of brake does a GM FWD vehicle use?
A prime example of this are GM FWD vehicles that are equipped with duo-servo rear drum brakes. Most FWD vehicles use a non-servo rear drum brake because of the braking balance of a FWD vehicle. These GM vehicles are “over-braked” in the rear which makes them very sensitive to rear brake problems.
How do I adjust the drum brake on my car?
To confirm your brakes are in good working order before you adjust them, check your vehicle for symptoms of a bad or failing drum brake. This article covers the adjustment process for drum brakes of the star wheel type. Step 1: Lift the rear end of the vehicle. Make sure the vehicle is in park and that the parking brake is set.
Can a out of round drum cause rear wheel lockup?
Brake drum condition should be factored in when determining the cause of rear wheel lockup. An out of round brake drum or drums that vary in diameter too much from side to side could cause a one wheel lockup condition (Figure 61.8). Measuring drum runout or out of roundness is not easy in the field.
How do you replace the brakes on a Chevy Silverado?
Use a large C-clamp. You put it on this end on the back of the caliper and on this brake pad and twist it in. This is going to push the caliper piston in and make it easier to pull the caliper up and off. Remove the large C-clamp, pull the caliper free, and set it aside. Pry up the brake pads.
Why are my brake pads sticking on my Silverado?
I just changed the rear brake pads on my 2002 Silverado. I put the new pads on and new hardware (sliders and clip in caliper) & greased them, put everything together and pushed the brake pedal to make sure is all okay and both calipers seem to refuse to release the pads as they should. I could barley turn the rear wheels.
What causes a brake caliper to not release?
A brake hose that is deteriorating on the inside can cause a caliper to not release too.
Where do you put the brake pads on a GMC Sierra?
Place new anti-rattle clips in position on the caliper bracket. Install the new brake pads onto the caliper mounting bracket. Place the pad with the squeal tab to the inside of the caliper.
What to do if you have a seized brake caliper?
Unsticking a Seized Brake Caliper If the cause of your brake issue is the parking brake cable/mechanism, a skewed pad, or the pads sticking to the disc, the remedy is fairly simple. Lubricating the parking brake system should fix that issue, and removing the pads and applying a small amount of grease to the edge should fix skewed pads.
What to do if your parking brake pads stick to the disc?
If the cause of your brake issue is the parking brake cable/mechanism, a skewed pad, or the pads sticking to the disc, the remedy is fairly simple. Lubricating the parking brake system should fix that issue, and removing the pads and applying a small amount of grease to the edge should fix skewed pads.
How do you install a caliper on a Honda Accord?
Rotate the caliper down and into position over the pads and the caliper bracket. Install the lower caliper bolt and torque it to 74 foot-pounds with a 3/8-inch torque wrench and socket. Install the tire onto the hub.