How do I reset my Dodge Ram 1500?
To reset the computer in your RAM 1500, take the following steps:
- Identify your battery’s negative cable.
- Disconnect the negative cable from the battery.
- Wait 20 minutes so that all systems have shut down.
- Reconnect the negative cable.
Where is the code reader on a Dodge Ram?
The 2019 Dodge Ram 1500 OBD location is in the driver’s footwell. It has a standard 16-pin connector on the front of the dash, behind a removable square panel.
What does P0403 code mean?
engine exhaust gas recirculation
P0403 is an OBD-II generic code that indicates that the engine control module (ECM) has detected the engine exhaust gas recirculation (EGR) circuit has malfunctioned. The ECM detected a short or open circuit in the EGR vacuum control solenoid or wiring to the solenoid.
How do I find OBD 1 codes?
The diagnostic connector is located under the dash panel by the driver side. To get the check engine codes to flash in your dash panel, use a jumper wire or a paper clip and connect terminals A and B of the diagnostic connector. Turn your ignition key on with engine off and the codes should start to blink.
How do you reset a PCM on a Dodge?
Dodge technicians often debate as to when and if you even need to reset the PCM.
- Open the hood of the Durango.
- Locate the battery and remove the black-wired negative terminal from the battery.
- Turn the ignition key to the “on/crank” position for 30 seconds, then replace the ignition key to the “off” position.
How do you reset the PCM?
Press and hold the PCM info button for approximately 10 seconds until the PCM reboots. Immediately select the following from the PCM CAR > OPTION > Set PCM System > Reset PCM > Vehicle Handover > Yes > Yes.
Why is my check engine light on in my Dodge Ram 1500?
When your check engine light comes on, this could be as simple as tightening or replacing your gas cap. One of the most normal and many cause is that your Ram 1500 gas cap is loose, damaged or missing.
Where is the OBD2?
Where is the OBD2 port? The OBD2 port location can vary depending on your car model. However, it is usually found within reach of the driver, underneath the steering wheel.
How do you read an error code on a Dodge truck?
In order to read the error code, the following procedure must be performed: Turn the ignition off. After 5 seconds, turn on the ignition, immediately turn it off, turn it on again, turn it off and on again. (Remember that ignition does not mean starting the engine).
What is the oxygen sensor code for a Dodge check engine?
P1196O2 Sensor 2/1 (Bank 2, Sensor 1) Slow During Catalyst Monitor – Read Our Article on Oxygen Sensor CodesFor Help With This Dodge Check Engine Light Code P1197O2 Sensor 1/2 (Bank 1, Sensor 2) Slow During Catalyst Monitor – Read Our Article on Oxygen Sensor CodesFor Help With This Dodge Check Engine Light Code
What are the codes for a Dodge OBDII?
OBDII Dodge Code Definitions. 1 Dodge Codes 2 Trouble Code 3 P0171 4 P0300 5 P0301 6 P0340 7 P0420 8 P1000 – P1099 (Fuel and air metering and auxiliary emission control) 9 P1200 – P1299 (Fuel and air metering – injector circuit) 10 P1300 – P1399 (Ignition system or misfire)
Where to find check engine light codes on Dodge?
These are listed in numerical order for easy searching. When retrieving Dodge check engine light codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located near the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.