How do I remove the right rear interior panel without?
If you need to remove the rear blower motor follow these instructions:” (1) Disconnect and isolate the battery negative cable. (2) Remove the right quarter trim panel and right D-pillar trim panel from the quarter inner panel (Refer to 23 – BODY/INTERIOR/QUARTER TRIM PANEL – REMOVAL).
How do you remove trim from a door panel?
Let’s Get Started. 1. Remove Small Trim Pieces. Most door panels will have small trim pieces located at the top of the panel at either the right or left side. Use a small screw driver or trim removal tool and detach (pop off) any trim pieces above the door panel. Here is an upper trim piece to the left of the panel.
How to remove and refit interior trim panels?
12 Peel back the edges of the trim panel and remove it. 13 Refitting is a reversal of removal, but refit the windscreen as described in Section 20. 14 Remove the two seat belt anchorages from the pillar. 15 Pull off the weatherstrips from the door apertures. 16 Remove the upper trim panel from the pillar.
What to remove from the rear of a Honda?
Put on gloves to protect your hands. Take care not to bend or scratch the trim and panels. Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Remove these items: Rear door sill trim Cargo area floor mat, cargo floor lid, cargo storage bin Rear trim panel Tie-down hooks
If you need to remove the rear blower motor follow these instructions:” (1) Disconnect and isolate the battery negative cable. (2) Remove the right quarter trim panel and right D-pillar trim panel from the quarter inner panel (Refer to 23 – BODY/INTERIOR/QUARTER TRIM PANEL – REMOVAL).
Put on gloves to protect your hands. Take care not to bend or scratch the trim and panels. Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Remove these items: Rear door sill trim Cargo area floor mat, cargo floor lid, cargo storage bin Rear trim panel Tie-down hooks
How to remove the interior panels on a Honda?
Install the panel in the reverse order of removal, and note these items: Check the clips for damage or stress-whitening, and replace them with new one. Make sure there are no twists or kinks in the seat belt. Push the clips and hooks into place securely. Well I hope this was what your looking for if not im sure i can get you what you need
How to remove the trim from a Honda CRV?
-1 Open the lid (B) and remove the screw (C), then remove the cargo hook (D).-2 Release the hooks (E), then remove the jack cover (F).-3 Remove the clip (G), then pull the trim panel back by hand to detach the clips (H, I).-4 Release the hooks (J) from the C-pillar trim (K) and D-pillar trim (L), then pull the trim panel forward.
What should I do if my car is converted to carry passengers in the rear?
Additional seats should be fitted securely so that they are likely to remain in place in the event of an accident. We recommend that you seek the advice of a reputable garage or vehicle converter.
What are the regulations on carrying passengers in the rear?
However, Regulation 100 of The Road Vehicles (Construction & Use) Regulations 1986 (SI 1986 No. 1078) will apply. This requires: the number of passengers carried, and the manner in which any passengers are carried in or on a vehicle
How to replace your car door ( with pictures )?
1 Turn the car on and actuate all of the switches on the door to make sure they are all working. 2 Roll the window all the way up and all the way down. Make sure the new window has the entire range of motion that the… More …
How do you remove trim on a Subaru Liberty?
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2). Remove the quarter trim panel from the vehicle. Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
How to remove the interior panels from a Subaru wagon?
Remove the screws all the way at the back where the cargo cover hooks in when extended. Pop up the little beige hooks on the side of each wheel well hump and remove the screws in them. Remove the clip that attaches the trunk wall panel that you’re trying to remove to the rear door scuff plate.
How do you remove the cargo cover on a Honda Accord?
Pop off the oval trim panels on each side just underneath the metal things where the cargo cover mounts. Remove both of the screws under there. Push on the cargo hooks to make them go down, then remove the screws in there. Remove the screws all the way at the back where the cargo cover hooks in when extended.
What kind of tool do I need to remove trim from my car?
Use a Molding and Trim Remover Tool for Vehicle Work. Prevent unsightly damage by using a specialized tool to remove molding and trim. Specialized tools are useful for removing a dashboard, door panels, fasteners, molding, trim or wheel hubs.
Where to get the best molding and trim remover tools?
AutoZone offers the lowest prices on molding and trim remover tools. These tools can come in handy for a variety of vehicle repairs and modifications. Once you have a set of molding and trim tools, you can remove many different types of components in order to complete repair or maintenance tasks on almost any car or truck.