How big is the brake bracket on a 15 Cherokee?
Welcome @Gripster ….i don’t own a ’15 Cherokee but confirm the following internet info with the factory service manual or FCA parts department: front caliper bracket is 129 ft/lbs and the rear caliper is 89 ft/lbs. The caliper guide pins are 32 ft/lb
What are the torque specifications of a Jeep Cherokee?
31.18 XJ – FRONT Brake Hose to Caliper Inlet Fitting Bolt Type: Bolt 27.12 XJ – Brake Pedel Pivot Pin Nut
Where are the brake pads on a 2015 Jeep Cherokee?
Remove the two old brake pads from the bracket and make a mental note of where the wear indicator or “squeal” bars are situated. On this 2015 Cherokee, the wear bars were situated at the bottom of both the inner and outer brake pads.
What kind of bolts are in a Jeep Cherokee?
27.12 XJ – Brake Pedel Pivot Pin Nut Type: 7.5 10.17 XJ – REAR Wheel Cylinder Mounting Bolts Type: Bolt 40.67 XJ – FRONT Caliper Mounting (Guide) Pins Type: Bolt 104.4 XJ – FRONT Caliper Achor Plate Bolts Type: Bolt 40.67 XJ – REAR Crossmember to Chassis Sill Bolts Type: Bolt
Welcome @Gripster ….i don’t own a ’15 Cherokee but confirm the following internet info with the factory service manual or FCA parts department: front caliper bracket is 129 ft/lbs and the rear caliper is 89 ft/lbs. The caliper guide pins are 32 ft/lb
31.18 XJ – FRONT Brake Hose to Caliper Inlet Fitting Bolt Type: Bolt 27.12 XJ – Brake Pedel Pivot Pin Nut
Remove the two old brake pads from the bracket and make a mental note of where the wear indicator or “squeal” bars are situated. On this 2015 Cherokee, the wear bars were situated at the bottom of both the inner and outer brake pads.
How much torque does a front brake caliper have?
Application Torque (Nm) Torque (FtLb) Notes Brake caliper bleed nipple 5 3.685 Front brake caliper mounting bolts 28 20.636 Front brake caliper pad retaining pin 18 13.266 I’ve attached the spec chart. Hope this is what you needed.
What kind of caliper mount does a jeep have?
Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37″ Toyo MTs.
Are there caliper mounting bolts for Jeep Liberty?
Caliper Mounting Bolts sets provide direct replacement for a proper fit every time. Our durable steel design helps to install the tool easily. Great parts!! Great parts!! The bolt is longer than he original bolt in my 2002 Jeep Liberty Limited. Website said this is an exact match.
What’s the name of the caliper bracket bolts?
On mine, the front 2 and rear 2 caliper bracket bolts are called a Torque-to-yield fastener. A torque to yield fastener (TTY) or stretch bolt is a fastener which is torqued beyond the state of elasticity and therefore undergoes plastic deformation, causing it to become permanently elongated. This is why they are a one time use.
How to remove the caliper mount on a jeep?
External Torx E-20 to remove (2) single use caliper bracket bolts–order (4 [to complete both sides]) 06510023AA From dealer in advance. Note: three of mine came out with my impact gun @ 90 psi.
Caliper Mounting Bolts sets provide direct replacement for a proper fit every time. Our durable steel design helps to install the tool easily. Great parts!! Great parts!! The bolt is longer than he original bolt in my 2002 Jeep Liberty Limited. Website said this is an exact match.
On mine, the front 2 and rear 2 caliper bracket bolts are called a Torque-to-yield fastener. A torque to yield fastener (TTY) or stretch bolt is a fastener which is torqued beyond the state of elasticity and therefore undergoes plastic deformation, causing it to become permanently elongated. This is why they are a one time use.
How big is the brake bracket on a 2011 Jeep?
My 2011 without a doubt is a typical 6 sided bolt head, holding the caliper bracket/adapter to the steering knuckle. Hmmm, mine had a normal bolt, a big one, but a normal six sided bolt head, every picture I’ve seen has normal bolt as well? I remember somewhere between 19mm to 22mm. Do you have an SRT with the Brembo Brakes?