Do I need to replace both camshaft sensors?

Two on each head and one for each camshaft. I wouldn’t recommend replacing camshaft sensors without a thorough diagnosis. The 1200 camshaft code is a cam timing problem. It could be a mechanical problem with the chain or a problem with the system that adjusts the variable valve timing.

How much does it cost to replace a cam sensor?

To replace a camshaft position sensor, you can expect to pay anywhere from $95 to $200. Parts alone will run about $25 to $100. Labor costs will be in the range of $70 to $100 for professional replacement. Expect to pay more if you have a luxury vehicle or are having your local car dealership perform the replacement.

Does camshaft sensor affect performance?

When the camshaft sensor malfunctions, it can affect the vehicle’s performance, from engine speed to fuel economy. The camshaft sensor is an integral part of the engine’s operating system, and losing its functionality can be the tip of the iceberg for greater engine failure.

Can you drive with a bad cam sensor?

Yes, it is safe to drive with a bad camshaft sensor. However, the performance of your engine will not be as good and fuel consumption may increase. In some cases, the camshaft may need replacement if there are any other symptoms of failure on this component. …

Can camshaft sensor cause overheating?

Question: Can a faulty camshaft sensor cause engine to overheat? Answer: No, but this post might help: https://hubpages.com/auto-repair/What-Causes-a-Car…

Where is the camshaft sensor located on a 3800 V6?

On the 3800 V6, the camshaft position sensor is located behind the water pump pulley. If you were to look at the pulley straight on, it is at about the 9 o’clock position. Where is the crank sensor located at. The CKP- Crankshaft Position Sensor, is located behind the crank pulley, It will need to be removed to get to the sensor.

Where is the air temp sensor located on a 3800 V6?

That ambient air temp sensor is located on the front core support, in front of the radiator. Left or right side depending on make, model, and year vehicle. where is the cam shaft position sensor at. On the 3800 V6, the camshaft position sensor is located behind the water pump pulley.

Where is the speed sensor on a GM 3800?

Answer: In most cars, the vehicle speed sensor is located in the tail shaft housing of the transmission. This is where the axle comes out on the passenger side of the trans. On front wheel drive cars. Best viewed from under the car. Where is the map sensor on this 3800 GM v6?

Where is the temperature sensor on a LeSabre 3800?

The CKP- Crankshaft Position Sensor, is located behind the crank pulley, It will need to be removed to get to the sensor. Buick Lesabre 3800 v-6. Temperature gauge needle laying down to the right past the H.

Do I need to replace both camshaft sensors?

Where is camshaft position sensor a bank 1 located?

Beneath the timing belt cover is where the CMP Sensor is mounted. The camshaft position sensor can be found in the right side of the engine compartment at the rear of the valve cover.

What happens when a camshaft sensor goes bad?

Poor Drivability A failing camshaft position sensor begins losing its ability to quickly transfer data. Mismatched fuel delivery and ignition timing, even if off by a few milliseconds, will cause your vehicle to sputter, accelerate poorly, lack power, stall or even shut off.

Do cars have 2 camshaft sensors?

Your vehicle should be equipped with four different camshaft position sensors, one for each of the engine’s camshafts. They are mounted in the front of the cylinder heads, near the camshaft actuators, across from each other.

How much does it cost to replace a camshaft position sensor?

What is the typical cost for Camshaft Position Sensor Replacement? In most case, this is not a expensive repair. The sensor will cost somewhere between $50 and $100 depending on the manufacturer. Installation can vary depending upon the car, and will run from $40 to $200 depending upon the location.

What is the difference between crankshaft position sensor and camshaft position sensor?

The crankshaft position sensor monitors as a multifunctional sensor used to set ignition timing, detect engine RPM and relative engine speed. The camshaft position sensor is used to determine which cylinder is firing to synchronize the fuel injector and coil firing sequence.

Can you still drive with a bad camshaft position sensor?

Your car won’t fail right away if there’s a problem with your camshaft ignition sensor by any means. You can still drive without one, but the overall performance of your vehicle will degrade over time.

Navigation