Can a shower drain be moved?
Sometimes moving a shower drain requires removing a concrete floor. Many bathroom remodeling jobs involve moving or replacing the shower stall. This often requires moving a drain connection that penetrates a concrete floor.
How do you remove old lead and oakum joints?
Remove all of the Oakum using pliers, scrapers or a rotary tool. (Because Oakum will burst into flame if you get it hot and expose it to air, it’s covered in tar after all…) At this point you can use a small blowtorch to slowly melt the remaining lead.
How much does it cost to move shower plumbing?
If you’re relocating the shower, expect to pay an extra $900 – $1,200 (same as the toilet). There are specific codes that plumbers must follow to make sure drains and vents are correctly angled and securely fitted.
Does the shower drain have to be centered?
The shower drain has to be at the lowest point of the shower floor, and so the floor has to slope down toward the drain from all directions. For showers that have a bench built in, placing the drain under the bench will keep it out of the way.
Can I cut cast iron with an angle grinder?
A circular or miter saw with a metal cutting blade. The angle grinder is probably going to be your best bet for making cuts in the cast iron piece. The grinder offers the best option for getting the cuts where you want them and keeping them relatively smooth.
Can a Dremel cut cast iron?
Cutting Cast Iron Pipes with Dremel A dremel is a kind of oscillating tool that contains a round shaped blade. It swings very fast and cuts the cast iron pipe. A 1/8 inch tungsten carbide carving bit is the best weapon for cutting, smoothing, and shaping such materials.
How do I remove a shower drain without caulking?
How to Remove the No-Caulk Shower Drain Cover:
- Use a screwdriver for the removal.
- Place the end of the screwdriver under the notched area of the strainer.
- Apply light upward pressure while being careful to not damage the finished surface.
- No-caulk shower drain cover should release from shower base.
Can I unscrew my shower drain?
Unscrew the knob on the top of the drain stopper to see if there is a set-screw underneath. If your drain stopper has a set-screw, use a small screwdriver or a hex key to unscrew it. Twist the entire stopper counterclockwise until it pulls free from its mounting post.
Where do you attach a P-trap to a shower drain?
Attach it to the 2-inch shower line in the wall with a reducer, directly below the shower line. Install the P-trap at the end of the feeder pipe closest to the new drain. Run the feeder pipe to the new drain hole location, attaching a vertical pipe segment here.
What’s the best way to reposition a shower drain?
How to Reposition Your Shower Drain Step 1 – Remove the Old Tub and Shower Pipe Step 2 – Mark the Existing Shower Drain and New Drain Hole Step 3 – Measure From the Old Drain to the New Drain Step 4 – Cut the Subfloor to Install the Feeder Pipe Step 7 – Attach the Feeder Pipe to the Drain and Shower Lines Step 8 – Lay the New Shower Floor
Where does a cast iron drain pipe go?
But It was common in previous generations for builders to rout (usually cast iron) drain pipes from ground-level outside of a building into the building, under the basement floor slab, and out to the municipal sewer system. These drains were used to receive roof gutter drainage and dispose of it into the city sewers.
What makes a cast iron sewer line leak?
Stains on the upper section of piping indicate that this drain system has been leaking. Our photograph above shows three clamp-on connectors joining cast iron and plastic drains to the cast iron sewer line. Our photograph shows an odd double-hub connection on a vertical section of cast iron drain piping in a 1935-built home in poughkeepsie, NY.
Are there p traps in the shower drain?
When it comes to shower P-traps, a lot of homeowners don’t even know what they’re for, if their shower drains are built with them, and how to replace them. If you’re unfamiliar with the P-trap, then read on. You’ll be glad you did.
Is there a way to install a shower drain from the top?
A special drain assembly mounts from the top and clamps onto the shower pan. If you have a leaky shower drain and don’t want to cut open a finished ceiling to get at it from below, consider using a special drain such as the WingTite Drain, which can be installed from above if the drain is in a plastic or fiberglass shower base.
What makes a cast iron drain pipe improper?
Improper cast iron pipe connections or retrofit connections (see our photo just below), including poorly-prepared lead hub joints as well as use of improper clamp on or hubless connectors
Can you replace cast iron drain pipe with ABS?
Here I will be replacing the cast iron drain system to the master bathroom with ABS drain piping. I will be cutting the cast iron out from the base at the foundation and joining the old to the new. ALWAYS CONSULT A PROFESSIONAL PLUMBER BEFORE ATTEMPTING REPAIR. Loading…