Are there any Windows gauges or interior lights?

Us too any solution. 2008 f150 ford. Also bulb. Now no windows gauges etc… Fuses look good and replaced. 8 people found this helpful. More than likely cluster fuse is bad I had the same problem and the guy said in the post above yours it was F 21 cluster fuse and it says cluster keep a lab in the manual that is it

Why is my power window not working on my Oldsmobile Intrigue?

The problem is likely to be a bad connection at the fuse box or ignition switch. What would cause no power to the rear right window of a 2000 Oldsmobile Intrigue? GMC power window troubleshooting for this problem will require a voltmeter. On the switch for this window, check for battery voltage at the purple and light green wires.

How can I tell if my GMC power window is working?

On the switch for this window, check for battery voltage at the purple and light green wires. If there is power, then check the dark blue wires at pin B of the window switch for voltage. If no voltage is detected on any or some of the wires, the wiring in the door jamb should be wiggled while the voltage is monitored to see if the is a fluctuation.

What happens if your power window is not working?

This is just one example of how technology has made life so much more convenient for drivers. However, there is one downside to having power windows. If there is ever an electrical problem with your vehicle or the electric motor inside the door fails, you will not be able to open and close your window until you get the problem fixed.

What happens when your fuel gauge stops working?

All of a sudden my power windows, radio, and fuel gauge stopped working. I have checked all fuses and even replaced a sudden my power windows, radio, and fuel gauge stopped working..fuses… Vocational, Technical or Tra… 2004 Ford Escape with shift on column. Heard a pop. Smoke 2004 Ford Escape with shift on column. Heard a pop.

What kind of problem is a lost gauge?

First instinct would be a ground problem but from your description it sounds like a Class2 data line problem and not an easy fix without some advanced knowledge and a scantool.

What to do if your power window is not working?

Repair or replace wires if faulty. Replace MPX module (Figure 5) if no current is shown on your voltmeter. If module shows current but the motor doesn’t, replace the Window motor (Figure 6). Figure 5. MPX module. Figure 6. Window motor.

Why are my gauges not working on my GMC Sierra?

Of course they couldn’t read it with a scanner when it wasn’t working, there was no communication on the Class2 data line. This isn’t something you’re going to fix poking and prodding, and you may even do more damage. The dealer is the best bet to diagnose this, it could by any of the dozen or so modules causing this problem or any of the wiring.

What causes the cluster gauges to stop working?

In one of the youtube videos I watched, the guy mentioned that there are also three small surface mount resistors that control power to the entire cluster, and his were causing the entire gauge cluster to go dead. He reflowed them and corrected the issue. I had a issue pretty similar to this as well.

What to do if your YouTube gauges are not working?

Easy fix. How to reset. – YouTube Gauges not working? Instrument cluster not working ? Easy fix. How to reset. If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

Why are the gauges on my Dodge Grand Caravan not working?

If you own a 2001 or later Dodge Grand Caravan or Chrysler Town & Country van and your gauges are dead, the most common cause is a bad module that’s mucking up the digital data on the vehicle’s data bus. Start by performing a self test on the cluster. Ignition switch should be in the locked position.

Why is my Cluster gauge on my Tahoe Yukon not working?

After a little research it turned out to be a common problem where the seven little surface mount resitors that power the display overheat and break the solder connections. It was simple to reflow the solder with a little flux and a drop of fresh solder.

What to do if your dome light goes bad?

Some folks found a short in headlined to the dome light. If that fuse is blown or even if it isnt but your batteries are dead in the morning, remove the domelight housing and check voltage at bulb. If bad or off from what everything else gets, remove the whole housing to reveal a shorted wire.

Why do I have trouble shooting my gauge cluster?

I have been trouble shooting my instrument cluster for months! My gauge cluster, windows, radio would all come and go as they pleased for any amount of time you can think of. Seconds, minutes or days. It would happen in every circumstance you can think of; key on engine off, engine running at idle, left turn, right turn, braking, or accelorating.

Why are all of my gauges not registering?

The sending unit wire could be bad or broken, or the circuit from the gauge to the sender is incomplete. Without a ground, the gauge will not register. It is highly unlikely that all the sender units are bad, so we can rule that out. Of course, it is also possible that all the gauges are malfunctioning.

What should I do if my dash gauges are all out?

Dash gauges are all out and no power windows and no blower for air and heater and its as something shot or blew but the two places that I checked the fuses are not blown. What else might I do to see if the problem can be fixed without going into the shop? have the same problem? Will the vehicle start and run?

Why are the interior lights and radio not working?

the mechanic was looking to fix the interior light when the door is open (above ur head) he must have triggered a fuse which stoped clock and radio and all the interior lights to work also the dimmer for the dash isnt working on the fullest when set to highest level.

Why are my tach and Speedo radios quitting?

Other problems I have seen is a corroded connector on the ABS module, corroded wiring in the rocker sill harness, rodent damage, and even faulty radios. Why the tach and speedo would quit is a mystery, those are basically hard wired between the ECM and the cluster but anything is possible.

Why do my car gauges turn off and on?

Now the gauges turn off and on, is says damaged keys. Window wont come up, says pass door is open. Headlights flicker, turn signals dont work, inside lights come on and off, and now push start wont work. I can work on the mechanical but don’t know much on the electrical.

Why did my fuel gauge stop working on my explorer?

I hooked up a trailer that was wired incorrectly and it blew the trailer battery power fuse. At the same time, the fuel gauge seemed to st … read more Today, all the sudden, the fuel gauge, power windows and radio, all stopped working on my 2004 ford explorer. everything else seems to work fine.

What does it mean when your temperature gauge is not working?

The temperature sensor/sending unit is faulty. If this is the case your sensor will be reading the coolant temperature incorrectly and sending the wrong signal to the gauge. This could work in either direction and read as cool when it’s running hot or hot when it’s running cool. A malfunctioning circuit in the temperature gauge

When to troubleshoot a Peterbilt instrument panel?

If you’re experiencing problems with your instrument panel or sensors, troubleshooting your electrical panel is the first place to begin looking for a solution. Reset your circuit breaker. If you have an outage in your dashboard, like a radio that won’t play, you may need to reset your circuit breaker in the electrical panel.

Why are there no windows and no radio?

However, as a consequence, I’m left with no power to my windows, overhead interior lights, radio, and the dash gauges no longer work. The dash, still displays my air bag yellow symbol, because the wires are disconnected under the drivers seat, it blinks then stays on.

What to look for in your car’s electrical panel?

Check for corrosion. Corroded wires can lead to problems like alarms going off without cause or dashboard lights flashing on and off uncontrollably. Check for leaking around the electrical panel, which could be coming from the windshield or the pass-through holes that feed the wires into the electrical panel.

How to turn on / off comfort turn signals?

Turning On/Off the feature is found in Adaptation. Select “Lights: Comfort Turn Signals” from the drop down list, choose 0 = Comfort Turn Signals inactive -OR- 1 = Comfort Turn Signals active.

Do you need a turn signal on a VW Golf?

The headlights must be turned on and the steering wheel must be in the turning direction. The headlights must be turned on and the turn signal must be on in the turning direction. Also see Byte 17, Adaptive Light/Cornering Light Variant.

First instinct would be a ground problem but from your description it sounds like a Class2 data line problem and not an easy fix without some advanced knowledge and a scantool.

Where does power come from to window fuse 601?

620 I jumped hot wire to window fuse 601 & they worked, where does power come from to it? their is another fuse box under the hood on drivers side fender well.has the big amp fuses and relays in it.one thing check ecm or pcm fuse in box inside cab.

What do you do when your instrument cluster doesn’t work?

Also when you drive the car, the speedometer and the rpm gauge doesn’t move. Everything light wise works. Everything works except the rpm, speedometer, temperature and gas gauge. All fuses and relays are good. I’ve even changed the instrument cluster and the BCM. Still none of the gauges work.

Can a Metra Install Kit work on a radio?

I used the metra install kit for the radio and the radio works fine exvept it does not turn on in the accessory position of the key. Does anybody have any suggestions that I can try or have a wiring diagram for the wiring harness in the audio system?

Why is my test light not working on my GMC Sierra?

Of course it would cause it to quit, the test light would pull the data line down and kill communication. Of course they couldn’t read it with a scanner when it wasn’t working, there was no communication on the Class2 data line. This isn’t something you’re going to fix poking and prodding, and you may even do more damage.

Navigation